Flair 58x User manual
What’s Included in Your Flair 58x Flair 58x Quick Setup Instructions
Watch our full online tutorials via the QR Code! Filling Your Flair 58x with the Valve Plunger Preheating Your Flair 58x
Filling Your Flair 58x with the Valve Plunger
(a) Fill brew cylinder to rim with water (b) Raise lever enough to
unseat stem and open valve allowing water to ll head space below
(c) Continue to raise lever slowly, and water will pass through the
valve and into the brewing chamber (d) Top-o chamber through
opening made between stem and plunger once lever is fully raised
(a)
(c) (d)
(b)
1 22
(a)
(b)
3
Bolt base & lever
assembly together
rmly
Remove preheat cap & install brew
cylinder onto brew base. Rotate
counterclockwise to lock
Align (a) plunger
stem tabs to slots on
valve plunger. Rotate
(b) stem to lock.
Gauge will face front
What’s Included:
1) Lever
2) Lever Assembly
3) Pressure Gauge
4) Plunger Stem
5) Lever Hook
6) Valve Plunger
(in Brew Cylinder)
7) Brew Cylinder
8) Brew Base
9) 58mm Portalter
10) Base
11) Drip Tray
12) Tamper
13) Kettle Preheat Cap
14) Puck Screen
1)
3)
4) 5) 6)
7)
8)
11)
12)
13)
2)
9)
14)
10)
(a) Raise lever & unlock and lift lever hook (b) Remove the brew
head by turning clockwise with gauge in place (c) Add Open Preheat
Cap onto bottom of brew head (d) Lift kettle top and replace with
brewhead (e) Turn plunger stem counterclockwise until two tabs
align with openings in plunger, leave in place to act as a release valve
(f) Boil water to preheat
(a) (c)
(d)
(b)
(e) (f)
*NOTE: If the brew head does not t on your kettle, preheat
your chamber with boiled water and the valve plunger
lowered. Purge and repeat as necessary.
4
Lower lever hook and
connect to plunger
stem
QUICK START GUIDE - The Flair 58x
Video Tutorials: https://airespresso.com/air-58x-tutorials/
Contact Flair: service@airespresso.com
Watch Our Training Videos Online! Brewing with Your Flair 58x Cleaning Your Flair 58x
Video Tutorials
#1 - Prepare the Flair
(a) Boil water and preheat your Flair 58x brew cylinder via the described
method (b) Grind 18-20 grams of freshly roasted beans with burr grinder
#2 - Prepare the Portalter & Brew Head
(a) Add fresh grounds to portalter and tamp (b) Add puck screen on
top of tamped grounds (c) re-attach preheated brew head to brew base
and (d) insert portalter by aligning it with the brew base and rotating the
portalter handle counterclockwise until it is rmly in place, at roughly the
4 o’clock position (Do not over-rotate) (e) Fill your brew head using the
valve plunger
#3 - Brew your Espresso
(a) Slowly lower lever to build pressure and begin brewing (b) Target a
shot duration of 30-35 seconds at 6-9 BAR (c) When desired shot weight/
volume is reached, or lever is fully lowered, raise the lever to start position
#4 - Purge your System
(a) Place an empty cup on drip tray (b) Expel remaining brew water by
lowering lever all the way down and allow the remaining liquid to drain
(c) Rotate portalter clockwise to remove for cleaning
*Use the QR code to watch simple brewing tutorials online!
28 Hammond Street, Suite B
Irvine, CA, 92618 USA
© Intact Idea, All Rights Reserved
Flair is a trademark of Intact Idea, LLC
Designed in California
Made in China
1. Use the stem to pull out
plunger while brew cylinder
is installed on base.
3. For more thorough
cleaning, place a cup
beneath your Flair 58x
and ush with cool water
before wiping.
2. Use damp cloth to wipe
the inside and bottom of
the brew head. Also wipe
the plunger.
Before cleaning, always ensure that your Flair 58x’s brew head has cooled
and never immerse the brew head in water.
No Soap Needed!
Keep Outside
Surface &
Wires Dry!
See our online tutorials for more information on cleaning and storing
your Flair 58x via the QR code on this manual.
Scan for Tutorials
Other Flair Coffee Maker manuals
