Fleece FPE-CRR-20-0806 Service manual

FPE-2018-15
October, 2018
Page 1 of 3
SUBJECT: CUMMINS REGULATED RETURN FUEL DISTRIBUTION BLOCK
FITMENT: 2007.5 –2018 6.7L Dodge Cummins
KIT P/N: FPE-CRR-20-0806
ESTIMATED INSTALLATION TIME: 1.5 Hours
KIT CONTENTS:
Item
Description
P/N
Qty
1
Fuel Distribution Block with Integrated
20PSI Regulated Return
FPE-34123
1
2
½” Push Lock CP3 Feed Fittings
FPE-CP3-FEED
2
3
-6AN to M12 Fittings
FPE-306-06-M12DBK
4
4
-6AN 120° to Push Lock Fitting
FPE-436-12006DBLK
1
5
-6AN 90° to Push Lock Fittings
FPE-436-9006DBLK
6
6
-6AN 45° to Push Lock Fitting
FPE-436-4506DBLK
1
7
-6AN Straight to Push Lock Fitting
FPE-436-0106DBLK
1
8
-8AN Straight to Push Lock Fitting
FPE-436-0108DBLK
1
9
-8AN 90° to Push Lock Fittings
FPE-436-9008DBLK
1
10
-8AN 45° to Push Lock Fitting
FPE-436-4508DBLK
2
11
-6 to 9/16”-18 Straight Male Fittings
FPE-AN920-06DBK
5
12
-8 to 3/4”-16 Straight Male Fittings
FPE-AN920-08DBK
4
13
-6AN (3/8”) Push Lock Hose
FPE-436-06BLK-6.0
6 ft
14
-8AN (1/2”) Push Lock Hose
FPE-436-08BK-4.0
4 ft
15
0 - 60 PSI Stainless Steel-Case Liquid-Filled
Gauge with 1 ½” dial
ASH-BY10YPE8CW
1
16
M8x1.25 x 55mm Stainless Steel Socket
Head Cap Screws
MMC-91292A156
2
17
12mm Sealing Washers
FPE-DW-12
2
18
1/8”NPT Hex Socket Plugs
FPE-AN932-02DBK
3
19
¾”-16 Hex Socket Plug w/ O-ring
FPE-814-08SDBK
1
CAUTIONS:
VERIFY THAT YOUR FUEL PUMP/LIFT PUMP CAN OPERATE AT 20+ PSI CONTINUOUSLY OR DAMAGE MAY OCCUR!
DO NOT USE THE FACTORY RETURN LINE TO RETURN FUEL TO THE TANK. IT IS TOO RESTRICTIVE.
USE TEFLON TAPE OR ANTISIEZE ON THREADS WHEN INSTALLING A GAUGE IN THE 1/8” NPT PORT(S)
WARNINGS:
Use of this product may void or nullify the vehicle’s factory warranty.
User assumes sole responsibility for the safe & proper use of the vehicle at all times.
The purchaser and end user releases, indemnifies, discharges, and holds harmless Fleece Performance Engineering, Inc.
from any and all claims, damages, causes of action, injuries, or expenses resulting from or relating to the use or installation
of this product that is in violation of the terms and conditions on this page, the product disclaimer, and/or the product
installation instructions. Fleece Performance Engineering, Inc. will not be liable for any direct, indirect, consequential,
exemplary, punitive, statutory, or incidental damages or fines cause by the use or installation of this product.

FPE-2018-15
October, 2018
Page 2 of 3
Visit https://fleeceperformance.com/resources for the latest instructions and videos.
For Technical Assistance contact Fleece Performance Engineering at 855-839-5040.
CP3 Low Pressure Feed
CP3 Return
Rail Return –Applicable only with regulated return distribution block
Head/Injector Return

FPE-2018-15
October, 2018
Page 3 of 3
Push Lock CP3 Fittings with
integral sealing washers (item 2)
-6AN to M12 Fitting (item 3)
-6AN 90° to Push Lock Fittings (item 5)
-6AN 120° to Push Lock Fitting (item 4)
-6AN to M12 Fitting (item 3)
-6 to 9/16”-18 Straight Male Fittings (item 11)
-8 to 3/4”-16 Straight
Male Fittings (item 12)
¾” Hex Plug (item 19)
or -8 to 3/4”-16 Straight
Male Fittings (item 12)
1/8”NPT Plugs (item 18),
Pressure Gauge (item 15),
WIF or other sensors
Visit https://fleeceperformance.com/resources for the latest instructions and videos.
For Technical Assistance contact Fleece Performance Engineering at 855-839-5040.