Fleet Complete MGS150 User manual

MGS150 KIT
INCLUDES
MGS Device
Mounting Cradle
Power Harness
5 Zipties
1 Blue Terminal Ring
FLEET TRACKER MGS150
Hardwire Installation
v. 11/17/15
Scan the code for video installation instructions
or go here fleetcomplete.com/mgs150hardwire

MGS150 WIRING SCHEMATIC
OVERVIEW OF THE MGS150 LEDS
The MGS150 LED indicator lights have been designed to provide a
simple visual reference regarding the device’s current status. The
table describes each status and the respective LED indications.
Green LED Red LED
OFF Power down mode ON External power issue
3 times No GPRS / No GPS ON Internal battery issue
2 times No GPRS / Fix GPS 1 time Shutdown / Standby mode
1 time GPRS OK / No GPS 2 times Idle / Sleep
INSTALLATION
1. Run the ground (black) wire to a suitable
chassis ground by using the crimp ring
terminal.
2. Run the positive (red) wire to the
constant power (+12 volts DC at all
times) and splice an in-line fuse holder to
the end. This is to protect the wire run.
3. Run the ignition switch input wire (white)
to the primary ignition wire in the vehicle.
Locate the appropriate wire under the dash.
When the ignition key is turned to the “On
or Run” position, this will show +12 Volts DC.
Installation Guide: MGS150 Hardwire
For technical support call 1 800 220 0779 | support@fleetcomplete.com

4. Run up to 4 zipties on the bottom of the
modems’ cradle. Snap the modem into the
cradle and secure it with a ziptie across the
top and around the cradle.
5. Connect the power harness to the modem.
6. Turn on the ignition. On the modem, switch
the back-up battery power switch to ON (I).
7. Mount the device in a location with least
amount of exposure to damage by people
or objects. Possible mounting locations are
under the central console, behind the dash
or behind the glove compartment.
8. Validate that the unit is setup in the Fleet
Complete Application by logining into your
account. Your account login is sent to the
main contact listed on the account at the
time of purchase.
9. Update the asset in Fleet Complete with corresponding Device
IMEI Number, Vehicle ID, VIN and Odometer reading.
There are two acceptable methods of making a wire connection:
• Solder the 12v Constant Power and Ground cables to the vehicles
power center.
• Splice and weave wires to 12v Constant Power and Ground cables.
Important: Hardware warranty will be voided if the device is
not installed according to the instructions.
For technical support call 1 800 220 0779 | support@fleetcomplete.com

Where in a truck is the best place to
install MGS150?
The best places to hardwire an
MGS150 in a vehicle are under the
center console, inside the dashboard
or under the glove compartment. Be
sure the device is not obstructed by
metal to avoid signal interference.
Can I install the modem outside
of the vehicle?
No. MGS150 is not weatherproof
and must be installed in a dry lo-
cation.
Can I wire the modem to the back
of the car radio or with other ac-
cessories?
No, you will not get proper idle
reports because the modem will
not be able to monitor the igni-
tion status properly. Ignition wire
must always be connected to the
vehicle’s ignition.
Where is the best place to get a
proper power and ignition?
Use the proper power or ignition
wire directly from the ignition
switch or behind the fuse box.
Do not use the intermittent pow-
er sources such as brakes power
wires, lights, radio or other acces-
sories. The modem will not receive
correct reading of the ignition
status and will cause “Movement
without ignition errors” and im-
proper idling report.
What is the best way to connect
the wires?
There are two acceptable methods
of making a wire connection:
soldering the wires with the
soldering iron or weave and crimp
the connectors with the use of the
proper crimping tool. DO NOT use
t-tap connectors. Always tape the
connections after soldering.
Can additional sensors, such as
door or temperature sensor, be
installed with the MGS150?
Yes, the power harness provided
with the kit allows up to 4 sensor
inputs, such as temperature, door,
PTO and other sensors.
What is the Default Data Settings
(DDS) for MGS150?
The DDS for MGS150 is to record 1
position every 2 min and transmit
location data to the server every 6
min. DDS Settings can be adjusted
in the Fleet Complete application
under Asset Settings.
What data is collected and trans-
mitted by the MGS150 device?
Date, time, location - address and
coordinates, speed, direction of
travel, ignition status, battery lev-
el, odometer, sensor status.
FAQ
1 800 220 0779 | fleetcomplete.com