Flip File Displays A2 Landscape User manual

A2 Landscape - Metal Swing Wall Displayer
Consists of…..
2x Metal Wall Brackets
5x Metal Poster Frames
5x A2 Landscape Acrylics
A2 Landscape Acrylics - Sizes
Height = 426mm x Width 618mm
A2 Landscape Frame - (When Assembled) - Sizes
2x Wall Brackets =
170mm x 30mm x 30mm
Frame protrusion = 651mm (approx)
Frame when opened like a book
Takes up = 651mm + 651mm = 1302mm (approx)
plus 2x wall holes of 15mm = 1302 + 30 =
W1332mm

Assembly Steps:
Step 1 - The Frame
4x Rod Lengths
4x Rod Corner Supports
4x Rod to Acrylic Holders
Supplied pre-assembled, as this picture >>>
5x Pre-assembled Frames supplied
Step 2 - The Acrylic
1. Acrylic Panels x 5 Units
2. Due to the nature of acrylic……
3. Acrylic is supplied separately
Why? -
1. If supplied pre-assembled there is a…..
2. High Risk of acrylic damage - hence……..
3. You will need to connect the acrylic
4. Don't worry its very easy - see 'Step 3'
Step 3 - The Assembly
1. Rod / Acrylic Corner Supports x4
2. Present acrylic to the metal frame
3. Front opening of acrylic facing you!
4. Now undo supports & slide onto the acrylic
5. Secure 2x Top Supports onto the Rods
6. Secure 2x Top Supports onto the Acrylic
7. Do not over-tighten to the acrylic!
8. Repeat 4,5,6,7 for the Bottom
9. Acrylic is now connected to the frame
10. Repeat all steps for remaining 5x frames
11. Now go to 'Step 4'

Step 4 - Wall Assembly
1. Wall Brackets supplied x 2 Units
2. Each Wall bracket has 5x Holes - Used for connecting the rods
3. Each Wall Bracket has 2x Holes - Used for connecting bracket to the wall
Connecting:
1. Decide the wanted height of the bottom of the display i.e. bottom wall bracket
2. Using a spirit level and a pencil hold bracket to wall and mark the 2x holes
3. Drill and raw-plug 2x holes, now secure bottom wall bracket to the wall
4. Now using a plumb-line, lightly mark 2x pencil marks up your wall
5. Assistant Required - Place first frame into first hole of bottom bracket
6. Now place the top bracket over the top of frame & first hole
7. Leave a space so the frame can be lifted upwards to remove in the future
8. Using a spirit level, lightly mark with a pencil underneath the top bracket
9. Now repeat step 3 - You should now have 2x wall brackets connected
Image 1 Image 2 Image 3
Step 5 - Completed Display
1. When all completed
2. You should have this all assembled >>>>
Step 6 - Adding Documents
1. Slightly bend forward the acrylic
2. Best to place documents back-to-back
3. Now slide document's) into acrylic

Individual Specs - Measurements:
Acrylics: 5x A2 Landscape Acrylics
Height 426mm x Width 618mm
Moulded acrylic with front acrylic slightly narrow
front acrylic allows for grippers to be attached on both sides
Wall Brackets: 2x Wall Brackets
170mm x 30mm x 30mm
L-Shaped with 2x Holes for wall attachment
L-Shaped with 5x Holes for 5x frames to be attached
Colour - Black
Metal Frames:
Metal Steel 6mm rods
Top & Bottom 6mm Rods
Top and bottom rods = 628mm
When attached to both end holders = 651mm
Side 6mm Rods
Side rods = 593mm
5x Frames equal
10x Rods at 593mm
10x Rods at 628mm
Supports:
Corner Supports = 15mm x 15mm
20x Corner Supports
Acrylic Supports = 24mm x 15mm
20x Acrylic Supports
Pre-assembled:
6mm Rod Frames are supplied "Fully Assembled"
Acrylics:
1. These are not supplied fully assembled
2. Why?
3. High risk of damage whilst in transit!
4. Please refer to page 2 - Step 3
Parcels: 2x Parcels are supplied with this order
1x Parcel contains = All Metalwork
1x Parcel contains = All Acrylics