Flowserve Centrifugal Pump M-TN User manual

USER INSTRUCTIONS
MHP-TN centrifugal pump
Single-stage, axial suction, vertical discharge type
centrifugal pump
PCN=71576313 – 02/07 (E)
Installation
Operation
Maintenance
These instructions must be read prior to installing,
operating, using and maintaining this equipment.

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 2 of 28 flowserve.com
CONTENTS Page
1 INTRODUCTION AND SAFETY .........................4
1.1 General........................................................4
1.2 CE marking and approvals............................4
1.3 Disclaimer.....................................................4
1.4 Copyright......................................................4
1.5 Duty conditions.............................................4
1.6 Safety...........................................................5
1.7 Nameplate and safety labels.........................8
1.8 Specific machine performance......................8
1.9 Noise level....................................................9
2 TRANSPORT AND STORAGE ......................... 10
2.1 Consignment receipt and unpacking ...........10
2.2 Handling.....................................................10
2.3 Lifting..........................................................10
2.4 Storage.......................................................11
2.5 Recycling and end of product life ................11
3 PUMP DESCRIPTION...................................... 11
3.1 Configurations............................................11
3.2 Nomenclature.............................................12
3.3 Coverage charts.........................................12
4 INSTALLATION................................................. 13
4.1 Location......................................................13
4.2 Foundation.................................................13
4.3 Grouting.....................................................14
4.4 Initial alignment...........................................14
4.5 Piping.........................................................15
4.6 Electrical connections.................................16
4.7 Final shaft alignment check.........................17
4.8 Protection systems.....................................17
5 COMMISSIONING, START-UP, OPERATIONAND
SHUTDOWN....................................................... 17
5.1 Direction of rotation.....................................17
5.2 Guarding.....................................................17
5.3 Priming and auxiliary supplies.....................17
5.4 Starting the pump........................................18
5.5 Running the pump ......................................19
5.6 Stopping and shutdown...............................20
5.7 Hydraulic, mechanical and electrical duty....20
5.8 Pumps for Food Use or Potable Water........21
Page
6 MAINTENANCE................................................21
6.1 General...................................................... 21
6.2 Maintenance schedule................................ 22
6.3 Spare parts................................................. 24
6.4 Recommended spares and consumable items
........................................................................24
6.5 Disassembly............................................... 24
7 FAULTS; CAUSES AND REMEDIES.................25
8 PARTS LISTAND DRAWINGS..........................26
8.1 Sectional drawings..................................... 26
8.2 Sectional drawings part list.........................27
8.3 General arrangement drawing.................... 27
9 CERTIFICATION...............................................27
10 OTHER RELEVANT DOCUMENTATION AND
MANUALS ...........................................................27
10.1 Supplementary User Instructions.............. 27
10.2 Change notes........................................... 27
10.3 Additional sources of information.............. 27

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 3 of 28 flowserve.com
INDEX Page
Additional sources (10.3).....................................27
Alignment of shafting (see 4.2, 4.4 and 4.7)
ATEX marking (1.6.4.2).........................................7
CE marking and approvals (1.2).............................4
Certification (9)....................................................27
Change notes (10.2)............................................27
Cleaning prior to operation (5.8.1) .......................21
Commissioning, start-up, operation (5).................17
Compliance, ATEX (1.6.4.1)...................................6
Configurations (3.1).............................................11
Copyright (1.4).......................................................4
Coverage charts (3.3)..........................................12
Direction of rotation (5.1)......................................17
Disassembly (6.5)................................................24
Discharge piping (4.5.3) ......................................16
Disclaimer (1.3).....................................................4
Dismantling (see 6.5, Disassembly) .....................24
Drawings (8.1).....................................................26
Duty conditions (1.5)..............................................4
Electrical connections (4.6)..................................16
End of product life (2.5)........................................11
Faults; causes and remedies (7)..........................25
Final checks (4.5.4) ............................................16
First pump start up (5.4.2) ...................................18
Foundation (4.2)..................................................13
Forces and moments (see 4.5.1)..........................15
General arrangement drawing (8.3) .....................27
Gland packing (6.2.4)...........................................23
Grouting (4.3) ......................................................14
Guarding (5.2).....................................................17
Handling (2.2)......................................................10
Hydraulic, mechanical and electrical duty (5.7).....20
Inspection (6.2.2 and 6.2.3).................................22
Installation (4)......................................................13
Internal coating (6.2.5).........................................23
Lifting (2.3)..........................................................10
Location (4.1).......................................................13
Maintenance (6)...................................................21
Maintenance schedule (6.2).................................22
Nomenclature (3.2)..............................................11
Nameplate (1.7.1)..................................................8
Operating limits (see 3.1).....................................12
Ordering spare parts (6.3.1).................................24
Parts lists (8.2).....................................................27
Piping (4.5)..........................................................15
Protection systems (4.8)......................................17
Pump masses (2.2.2) ..........................................10
Receipt and unpacking (2.1)................................10
Recommended spares (6.4).................................24
Recycling (2.5).....................................................11
Replacement parts (see 6.3 and 6.4)...................24
Running the pump (5.5).......................................19
Safety action (1.6.3)...............................................5
Safety labels (1.7.2)...............................................8
Safety markings (1.6.1)..........................................5
Safety, protection systems (see 1.6 and 4.8)
Page
Sectional drawings (8.1)...................................... 26
Sound level (see 1.9, Noise level).......................... 9
Sources, additional information (10.3).................. 27
Spare parts (6.3).................................................24
Specific machine performance (1.8)...................... 8
Standard maintenance (6.2.1) ............................ 22
Starting the pump (5.4)........................................18
Stop/start frequency (5.5.5).................................20
Stopping and shutdown (5.6)............................... 20
Storage, pump (2.4)............................................ 11
Storage, spare parts (6.3.2).................................24
Suction piping (4.5.2) .........................................15
Supplementary manuals or information sources.. 27
Thermal expansion (4.4.1) .................................. 14
Transport and storage (2) ................................... 10
Trouble-shooting (see 7)..................................... 25
Vibration (5.5.4)................................................... 19

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 4 of 28 flowserve.com
1 INTRODUCTION AND SAFETY
1.1 General
These instructions mustalways be kept
close to the product's operating location or
directly with the product.
Flowserve products are designed, developed and
manufactured with state-of-the-art technologies in
modern facilities. The unit is produced with great
care and commitment to continuous quality control,
utilizing sophisticated quality techniques, and safety
requirements.
Flowserve is committed to continuous quality
improvement and being at service for any further
information about the product in its installation and
operation or about its support products, repair and
diagnostic services.
These instructions are intended to facilitate
familiarization with the product and its permitted use.
Operating the product in compliance with these
instructions is important to help ensure reliability in
service and avoid risks. The instructions may not
take into account local regulations; ensure such
regulations are observed by all, including those
installing the product. Always coordinate repair
activity with operations personnel, and follow all plant
safety requirements and applicable safety and health
laws and regulations.
These instructions must be read prior to
installing, operating, using and maintaining the
equipment in any region worldwide. The
equipment must not be put into service until all
the conditions relating to safety noted in the
instructions, have been met.
1.2 CE marking and approvals
It is a legal requirement that machinery and
equipment put into service within certain regions of
the world shall conform with the applicable CE
Marking Directives covering Machinery and, where
applicable, Low Voltage Equipment, Electromagnetic
Compatibility (EMC), Pressure Equipment Directive
(PED) and Equipment for Potentially Explosive
Atmospheres (ATEX).
Where applicable the Directives and any additional
Approvals cover importantsafety aspects relating to
machinery andequipment and the satisfactory
provisionoftechnical documents andsafety
instructions.Where applicable this document
incorporates information relevant to these Directives
and Approvals.
To confirmthe Approvalsapplying andif the product is
CE marked,checktheserial number plate markings
andthe Certification. (See section9,Certification.)
1.3 Disclaimer
Information in these User Instructions is believed
to be reliable. In spite of all the efforts of Flowserve
Corporation to provide sound and all necessary
information the content of this manual may appear
insufficient and is not guaranteed by Flowserve as
to its completeness or accuracy.
Flowserve manufactures products toexacting
International Quality Management System Standards
as certifiedandaudited by externalQuality Assurance
organizations. Genuine parts and accessories have
been designed,tested andincorporatedinto the
productsto helpensure theircontinuedproduct quality
and performance inuse. As Flowserve cannot test
parts andaccessoriessourcedfromother vendors the
incorrect incorporation of such parts andaccessories
may adversely affect the performance and safety
features of the products. The failureto properly select,
install or use authorized Flowserve parts and
accessories is considered to be misuse. Damageor
failure causedby misuse is not covered by the
Flowserve warranty.In addition, any modificationof
Flowserve products or removaloforiginalcomponents
may impairthe safety of these products intheir use.
1.4 Copyright
All rights reserved. No part of these instructions may
be reproduced, stored in a retrieval system or
transmitted in any form or by any means without
prior permission of Flowserve.
1.5 Duty conditions
This product has been selected to meet the
specifications of your purchaser order. The
acknowledgement of these conditions has been sent
separately to the Purchaser. Acopy should be kept
with these instructions.
The product must not be operated beyond
the parameters specified for the application. If
there is any doubt as to the suitability of the
product for the application intended, contact
Flowserve for advice, quoting the serial number.
If the conditions of service on your purchase order
are going to be changed (for example liquid pumped,
temperature or duty) it is requested that the user
seeks the written agreement of Flowserve before
start up.

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 5 of 28 flowserve.com
1.6 Safety
1.6.1 Summary of safety markings
These UserInstructions containspecific safety
markings where non-observance of aninstruction
would cause hazards. Thespecific safety markings are:
This symbol indicates electrical safety
instructions where non-compliance will involve a high
risk to personal safety or the loss of life.
This symbol indicates safety instructions where
non-compliance would affect personal safety and
could result in loss of life.
This symbol indicates “hazardous substances
and toxic fluid” safety instructions where non-
compliance would affect personal safety and could
result in loss of life.
This symbol indicates safety
instructions where non-compliance will involve some
risk to safe operation and personalsafety and would
damage the equipment or property.
This symbol indicates explosive atmosphere
zone marking according to ATEX. It is used in safety
instructions where non-compliance in the hazardous
area would cause the risk of an explosion.
This symbol is used in safety instructions to
remind not to rub non-metallic surfaces with a dry
cloth; ensure cloth is damp. It is used where non-
compliance in the hazardous area would cause the
risk of an explosion.
This sign is not a safety symbol but indicates
an importantinstructionin the assembly process.
1.6.2 Personnel qualification and training
All personnel involved in the operation, installation,
inspection and maintenance of the unit must be
qualified to carry out the work involved. If the
personnel in question do not already possess the
necessary knowledge and skill, appropriate training
and instruction must be provided. If required the
operator may commission the manufacturer/supplier
to provide applicable training.
Always coordinate repair activity with operations and
health and safety personnel, and follow all plant
safety requirements and applicable safety and health
laws and regulations.
1.6.3 Safety action
This is a summary of conditions and actions to
prevent injury to personnel and damage to the
environment and to equipment. For products
used in potentially explosive atmospheres
section 1.6.4 also applies.
NEVER DO MAINTENANCE WORK
WHEN THE UNIT IS CONNECTED TO POWER
GUARDS MUST NOT BE REMOVED WHILE
THE PUMP IS OPERATIONAL
DRAIN THE PUMP AND ISOLATE PIPEWORK
BEFORE DISMANTLING THE PUMP
The appropriate safety precautions should be taken
where the pumped liquids are hazardous.
FLUORO-ELASTOMERS (When fitted.)
When a pump has experienced temperatures over
250 ºC (482 ºF), partial decomposition of fluoro-
elastomers (example: Viton) will occur. In this
condition these are extremely dangerous and skin
contact must be avoided.
HANDLING COMPONENTS
Many precision parts have sharp corners and the
wearing of appropriate safety gloves and equipment
is required when handling these components. To lift
heavy pieces above 25 kg (55 lb) use a crane
appropriate for the mass and in accordance with
current local regulations.
THERMAL SHOCK
Rapid changes in the temperature of the liquid within
the pump can cause thermal shock, which can result
in damage or breakage of components and should
be avoided.
NEVER APPLY HEAT TO REMOVE
IMPELLER
Trapped lubricant orvapor could cause anexplosion.
HOT (and cold) PARTS
If hot or freezing components or auxiliary heating
supplies can present a danger to operators and
persons entering the immediate area action must be
taken to avoid accidental contact. If complete
protection is not possible, the machine access must
be limited to maintenance staff only, with clear visual
warnings and indicators to those entering the
immediate area. Note: bearing housings must not be
insulated and drive motors and bearings may be hot.
If the temperature is greater than 68 °C (175 °F)
or below 5 °C (20 °F) in a restricted zone, or
exceeds local regulations, action as above shall
be taken.

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 6 of 28 flowserve.com
HAZARDOUS LIQUIDS
Whenthe pump is handling hazardous liquids care
must be takento avoidexposure to the liquid by
appropriate sitting of the pump, limitingpersonnel
access and by operator training. If the liquidis
flammable and/or explosive, strictsafety procedures
must be applied.
Gland packing must not be used when pumping
hazardous liquids.
PREVENT EXCESSIVE EXTERNAL
PIPE LOAD
Do not use pump as a support for piping. Do not
mount expansion joints, unless allowed by Flowserve
in writing, so that their force, due to internal
pressure, acts on the pump flange.
ENSURE CORRECT LUBRICATION
(See section 5, Commissioning, startup, operation
and shutdown.)
START THE PUMP WITHOUTLET
VALVE PART OPENED
(Unless otherwise instructed at a specific point in the
User Instructions.)
This is recommended to minimize the risk of
overloading and damaging the pump motor at full or
zero flow. Pumps may be started with the valve
further open only on installations where this situation
cannot occur. Pump outlet valve shall may need to
be adjusted to comply with the duty following the run-
up process. (See section 5, Commissioning start-up,
operation and shutdown.)
NEVER RUN THE PUMP DRY
INLET VALVES TO BE FULLY OPEN
WHEN PUMP IS RUNNING
Running the pump at zero flow or below the
recommended minimum flow continuously will cause
damage to theseal.
DO NOT RUN THE PUMP AT
ABNORMALLY HIGH OR LOW FLOW RATES
Operating at a flow rate higher than normal or at a
flow rate with no backpressure on the pump may
overload the motor and cause cavitation. Low flow
rates may cause a reduction in pump/bearing life,
overheating of the pump, instability and
cavitation/vibration.
1.6.4 Products used in potentially explosive
atmospheres
The followinginstructions for pumps andpump
units when installed in potentially explosive
atmospheresmust be followed to help ensure
explosion protection.
The terminology and procedures ensure that the
installed pump is in compliance with theEuropean
Directive 94/9/EC, known as the ATEX Directive, which
is mandatory in Europe and may also be specifiedin
other countries.Whereapplicable, both electricaland
non-electricalequipment must meet the requirements
94/9/EC.
Evenif the installationis in a regionwhere ATEXis not
theapplicable regulation, the general measures
describedshall be followed toensure safeoperation.
The measures are explained under the headings of:
Avoiding excessive surface temperature
Preventing build up of explosive mixtures
Preventing the generation of sparks
Preventing leakages
Maintaining the pump to avoid hazard
1.6.4.1 Scope of compliance
Use equipment only inthe zone for whichit is
appropriate. Always check that the driver, drive
coupling assembly, seal and pump equipmentare
suitably ratedand/orcertifiedfor the classificationofthe
specific atmosphere in whichtheyare to beinstalled.
Where Flowserve has supplied only the bare shaft
pump, the Ex rating applies only to the pump. The
party responsible for assembling the pump setshall
select the coupling, driver andany additional
equipment, with the necessary CE Declaration of
Conformity establishing it is suitable for the area in
which it is to be installed.
The output froma variable frequency drive (VFD)can
cause additional heating affects in the motor andso, for
pumps sets witha VFD, the ATEX Certificationforthe
motor muststatethat it iscovers the situationwhere
electricalsupply is from the VFD. This particular
requirementstill applies even if the VFD is in a safe
area.

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 7 of 28 flowserve.com
1.6.4.2 Marking
An example of ATEX equipment marking is shown
below. The actual classification of the pump will be
engraved on the nameplate.
II 2 GD c IIC 135 ºC (T4)
Equipment Group
I = Mining
II = Non-mining
Category
2 or M2 = High level protection
3 = normal levelof protection
Gas and/or Dust
G = Gas; D= Dust
c = Constructional safety
(in accordance withEN 13463-5)
Gas Group (Equipment Category 2 only)
IIA– Propane (typical)
IIB – Ethylene (typical)
IIC– Hydrogen (typical)
Maximum surface temperature (Temperature Class)
(seesection 1.6.4.3)
1.6.4.3 Avoiding excessive surface temperatures
ENSURE THE EQUIPMENT TEMPERATURE
CLASS IS SUITABLE FOR THE HAZARD ZONE
Pumps have a temperature class as stated in the
ATEX Ex rating on the nameplate. These are based
on a maximum ambient of 40 °C (104 °F); refer to
Flowserve for higher ambient temperatures.
The surface temperature on the pump is influenced
by the temperature of the liquid handled. The
maximum permissible liquid temperature depends on
the temperature class and must not exceed the
values in the table that follows.
The temperature rise at the seals, bearings and due
to the minimum permitted flow rate is taken into
account in the temperatures stated.
Temperature
class to
EN 13463-1
Maximum
surface
temperature
permitted
Temperature limit of liquid
handled (* depending on
material and construction
variant - check which is
lower)
T6
T5
T4
T3
T2
T1
85 °C (185 °F)
100 °C (212 °F)
135 °C (275 °F)
200 °C (392 °F)
300 °C (572 °F)
450 °C (842 °F)
Consult Flowserve
Consult Flowserve
115 °C (239 °F) *
180 °C (356 °F) *
275 °C (527 °F) *
400 °C (752 °F) *
The responsibility for compliance with the
specified maximum liquid temperature is with the
plant operator.
Temperature classification “Tx” is used when the
liquid temperature varies and the pump could be
installed in different hazardous atmospheres. In this
case the user is responsible for ensuring that the
pump surface temperature does not exceed that
permitted in the particular hazardous atmosphere.
If an explosive atmosphere exists during the
installation, do not attempt to check the direction of
rotation by starting the pump unfilled. Even a short
run time may give a high temperature resulting from
contact between rotating and stationary components.
Furthermore, confinement of liquid in the pump and
pipes must be avoided (valve closed). If the liquid
heats up this may cause excessive pressure and
lead to bursting of pump components.
Where there is any risk of the pump being run against
a closed valve generating high liquid and casing
externalsurface temperatures it is recommended that
users fit anexternalsurface temperature protection
device.
Avoid mechanical, hydraulic or electrical overload by
using motor overload trips, temperature monitor or a
power monitor and make routine vibration monitoring
checks.
In dirty or dusty environments, regular checks must
be made and dirt removed from areas around close
clearances, bearing housings and motors.
1.6.4.4 Preventing the build up of explosive
mixtures
ENSURE PUMP IS PROPERLY FILLED AND
VENTED AND DOES NOT RUN DRY.
Ensure pump and relevant suction and discharge
pipeline system is totally filled with liquid at all times
during the pump operation, so that an explosive
atmosphere is prevented. In addition it is essential to
make sure that seal chambers, auxiliary shaft seal
systems and any heating and cooling systems are
properly filled.
If the operation of the system cannot avoid this
condition the fitting of an appropriate dry run
protection device is recommended (eg liquid
detection or power monitor).
To avoid potential hazards from fugitive emissions of
vapor or gas to atmosphere the surrounding area
must be well ventilated.

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 8 of 28 flowserve.com
1.6.4.5 Preventing sparks
To prevent a potential hazard from mechanical
contact, the coupling guard must be non-sparking.
To avoid the potential hazard from random induced
current generating a spark the ground contact on the
baseplate must be used.
Avoid electrostatic charge: do not rub non-
metallic surfaces with a dry cloth, ensure cloth is
damp.
Where applicable the coupling must be selected to
comply with 94/9/EC and correct alignment must be
maintained.
Additional requirements for metallic pumps on
non-metallic baseplates
When metallic components are fitted on a non-
metallic baseplate they must be individually earthed
(grounded).
1.6.4.6 Preventing leakage
The pump must only be used to handle liquids
for which it has been approved to have the correct
corrosion resistance.
Avoidentrapment of liquid in the pump and associated
pipingdue toclosingof suctionand dischargevalves,
which could cause dangerous excessive pressuresto
occurif there is heat input to the liquid. Thiscanoccur if
the pump is stationary or running.
Bursting of liquid containing parts due to freezing
must be avoided by draining or protecting the pump
and ancillary systems.
Where there is the potential hazard of a loss of a
seal barrier fluid or external flush, the fluid must be
monitored.
If leakage of liquid to atmosphere can result in a
hazard, the installation of a liquid detection device is
recommended.
1.6.4.7 Maintenance to avoid the hazard
CORRECT MAINTENANCE IS REQUIRED
TO AVOID POTENTIAL HAZARDS WHICH GIVE A
RISK OF EXPLOSION
The responsibility forcompliance with
maintenance instructions is with the plant operator.
To avoid potential explosion hazards during
maintenance, the tools, cleaning and painting
materials used must not give rise to sparking or
adversely affect the ambient conditions.
Where there is a risk fromsuch tools or materials;
maintenance must be conducted in a safe area.
It is recommended that a maintenance plan and
schedule is adopted. (See section 6, Maintenance.)
1.7 Nameplate and safety labels
1.7.1 Nameplate
For details of nameplate, see the Declaration of
Conformity, or separate documentation included with
these User Instructions.
1.7.2 Safety labels
Oil lubricated units only:
1.8 Specific machine performance
For performance parameters see section 1.5, Duty
conditions.When the contract requirement specifies
these to be incorporated into User Instructions these
are included here. Where performance data has
been supplied separately to the purchaser these
should be obtained and retained with these User
Instructions if required.

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 9 of 28 flowserve.com
1.9 Noise level
Attention must be given to the exposure of personnel
to the noise, and local legislation will define when
guidance to personnel on noise limitation is required,
and when noise exposure reduction is mandatory.
This is typically 80 to 85 dBA.
The usual approach is to control the exposure time
to the noise or to enclose the machine to reduce
emitted sound.
You may have already specified a limiting noise level
when the equipment was ordered, however if no
noise requirements were defined, then attention is
drawn to the following table to give an indication of
equipment noise level so that you can take the
appropriate action in your plant.
Pump noise level is dependent on a number of
operational factors, flow rate, pipework design and
acoustic characteristics of the building, and so the
values given are subject to a 3 dBA tolerance and
cannot be guaranteed.
Similarly the motor noise assumed in the “pump and
motor” noise is that typically expected from standard
and high efficiency motors when on load directly
driving the pump. Note that a motor driven by an
inverter may show an increased noise at some
speeds.
If a pump unit only has been purchased for fitting
with your own driver then the “pump only” noise
levels in the table should be combined with the level
for the driver obtained from the supplier. Consult
Flowserve or a noise specialist if assistance is
required in combining the values.
It is recommended that where exposure approaches
the prescribed limit, then site noise measurements
should be made.
The values are in sound pressure level LpA at 1 m
(3.3 ft) from the machine, for “free field conditions
over a reflecting plane”.
For estimating sound power level LWA (re 1 pW)
then add 17 dBA to the sound pressure value.
Typical sound pressure levelLpA at 1 mreference 20 μPa, dBA
3 550 r/min 2 900 r/min 1 750 r/min 1 450 r/min
Motor size
and speed
kW (hp) Pump
only Pump and motor Pump only Pump and motor Pump only Pump and motor Pump only Pump and motor
< 0.55(< 0.75) 72 72 64 65 62 64 62 64
0.75 (1) 72 72 64 66 62 64 62 64
1.1(1.5) 74 74 66 67 64 64 62 63
1.5(2) 74 74 66 71 64 64 62 63
2.2(3) 75 76 68 72 65 66 63 64
3 (4) 75 76 70 73 65 66 63 64
4 (5) 75 76 71 73 65 66 63 64
5.5 (7.5) 76 77 72 75 66 67 64 65
7.5 (10) 76 77 72 75 66 67 64 65
11 (15) 80 81 76 78 70 71 68 69
15 (20) 80 81 76 78 70 71 68 69
18.5 (25) 81 81 77 78 71 71 69 71
22 (30) 81 81 77 79 71 71 69 71
30 (40) 83 83 79 81 73 73 71 73
37 (50) 83 83 79 81 73 73 71 73
45 (60) 86 86 82 84 76 76 74 76
55 (75) 86 86 82 84 76 76 74 76
75 (100) 87 87 83 85 77 77 75 77
90 (120) 87 88 83 85 77 78 75 78
110 (150) 89 90 85 87 79 80 77 80
150 (200) 89 90 85 87 79 80 77 80
200 (270)  85 87 83 85
300 (400) 87 90 85 86
The noise level of machines in this range will most likely be of values which require noise exposure control, but typical values are
inappropriate.
Note: for 1 180 and 960 r/min reduce 1 450 r/min values by 2 dBA. For 880 and 720 r/min reduce 1 450 r/min values by 3 dBA.

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 10 of 28 flowserve.com
In areas where the staff has to intervene, remember
that when the level of the sound pressure is:
below 70 dBA: it is not necessary to take special
precautions.
above 70 dBA: people working continuously in
the machine room must be supplied with
protective devices against noise.
below 85 dBA: no particular measures need to
be taken for casual visitors staying in the room
during a limited period.
above 85 dBA: the room must be considered as
a dangerous area because of the noise and a
warning sign must be fixed at each entry warning
the people coming into the room, even for a
short period, that they must wear hearing
protection.
above 105 dBA: special hearing protection
adapted to this noise level and to the spectral
noise components must be installed and a
warning sign to this effect erected at each entry.
The staff in the room must wear ear protection.
Make sure that the noise, which travels through the
walls and windows, does not generate too high noise
levels in the machine room's surroundings.
2 TRANSPORT AND STORAGE
2.1 Consignment receipt and unpacking
Immediately after receipt of the equipment it must be
checked against the delivery and shipping
documents for its completeness and that there has
been no damage in transportation.
Any shortage and or damage must be reported
immediately to Flowserve and received in writing
within one month of receipt of the equipment. Later
claims cannot be accepted.
Check any crate, boxes and wrappings for any
accessories or spare parts that may be packed
separately with the equipment or attached to
sidewalls of the box or equipment.
Each product has a unique serial number. Check
that this number corresponds with that advised and
always quote this number in correspondence as well
as when ordering spare parts or further accessories.
2.2 Handling
2.2.1 General instructions concerning handling
Boxes, crates, pallets or cartons may be unloaded
using forklift vehicles or slings dependent on their
size and construction. See 2.3.1 for positioning of
slings.
To lift heavy pieces above 25 kg (55 lb), use a winch
adapted to the mass and in accordance with the
current local regulations.
To lift machines or pieces with one or several
suspension rings, only use hooks and chains in
compliance with the local regulations concerning
safety.
Never put cables, chains or ropes directly on or in
the suspension rings. Cables, chains or lifting ropes
must never present excessive bending.
Never bend the lifting hooks, suspension rings,
chains, etc., whichshould only be made to endure
stresses within, calculated limits. Remember that the
capacity of a lifting device decreases when the
direction of the lifting force direction makes an angle
with the device axis.
To increase the safety and the efficiency of the lifting
device, all the lifting elements must be as
perpendicular as possible. If necessary a lifting beam
can be placed between the winch and the load.
When heavy pieces are lifted up, never stay or work
under the load or in the area, which could be in the
path of the load if it were to swing or fall away. Never
leave a load hanging from a winch. The acceleration
or the slowing-down of lifting equipment must stay in
the safety limits for the staff.
A winch must be positioned in such a way that the
load will be raised perpendicularly. Where possible
necessary precautions must be taken to avoid the
swing of the load, using for example two winches
making approximately the same angle, below 30°,
with the vertical.
2.2.2 Pumpmasses
Pump mass
Pump type kg lb
MHP-TN 100-65-315 134 295
MHP-TN 125-100-315 152 335
All motors (for masses see the motor
description plate) must be handled with a winch.
For masses above 25 kg (55 lb), manual
handling is forbidden.
2.3 Lifting
2.3.1 Slinging of motor pumps units
Use handling means in accordance with motor
pump unit mass mentioned on the CE plate. For the
masses of the pumps bare end of shaft see table §
2.2.2 and nameplate.
To avoid distortion, the pump unit
should be lifted as shown.

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 11 of 28 flowserve.com
Motor pump unit
Bareshaft pump
When handling always wear gloves, safety
boots and an industrial safety helmet.
For masses above 25 kg (55 lb), manual
handling is forbidden.
2.4 Storage
Store the pump in a clean, dry
location away from vibration. Leave piping
connection covers in place to keep dirt and other
foreign material out of pump casing. Turn pump at
intervals to prevent brinelling of the bearings and the
seal faces, if fitted, from sticking.
Do not store pumps starting on the fan guard.
The pump may be stored as above for up to 6
months. Consult Flowserve for preservative actions
when a longer storage period is needed.
2.5 Recycling and end of product life
At the end of the service life of the product or its
parts, the relevant materials and parts should be
recycled or disposed of using an environmentally
acceptable method and local regulations. If the
product contains substances which are harmful to
the environment, these should be removed and
disposed of in accordance with current regulations.
This also includes the liquids and or gases in the
"seal system" or other utilities.
Make sure that hazardous substances or toxic
fluid are disposed of safely and that the correct
personal protective equipment is used. The safety
specifications must be in accordance with the current
regulations at all times.
3 PUMP DESCRIPTION
3.1 Configurations
The centrifugal motor pump is designed for the
pumping of cold water or all clear liquids which are
not solid and liquid mixtures, non-corrosive, non-
abrasive when in contact with the pump motor unit
and its working parts (Important: for other liquids
consult Flowserve for beforehand advice).
The MHP-TN pump is a centrifugal, single-stage
pump with axial inlet and outlet in the vertical axis.
The pump must be stored in a non explosive,
ventilated location, sheltered from bad weather, dust
and vibrations.
The reliability of the delivered machine can only be
ensured if it is used according to the conditions given
in this manual. The maximum values specified in this
manual must never be exceeded.
Maximum working pressure at discharge
.................................................16 bar (232 psi)
Maximum working pressure at suction
.................................................10 bar (145 psi)
Maximum pumped fluid temperature
- Gland packing without cooling
..............................................105 °C (221 °F)
Minimum pumped fluid temperature
.................................................... -10 °C (14 °F)
Maximum ambient temperature.... 40 °C (104 °F)
Maximum solid suspension
........................................50 g/m3(0.003 lbm/ft3)
Density ..................................1
Viscosity................................1 mm2/s (31 SSU)
Maximum rotation speed (frequency 50 Hz)
....................................................... 2900 min-1
The maximum speed is shown on the
pump nameplate.

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 12 of 28 flowserve.com
3.2 Nomenclature
Characteristics shown on the nameplate fixed on the pump are as shown below:
Each pump is supplied with the following nameplate:
Each pump unit is supplied with the following nameplate:
Mass of the set
3.3 Coverage charts
3.3.1 2900 min-1 (50 Hz): coverage charts (Q, H)
Pump type
Speed of rotation
Flow rate
Year of construction +
Manufacture number
Head
Radial/thrust bearing
Mass
Maximum admissible
Pressure at 20 °C (68 °F)
Maximum / minimum
temperature

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 13 of 28 flowserve.com
4 INSTALLATION
Equipment operated in hazardous locations
must comply with the relevant explosion protection
regulations. See section 1.6.4, Products used in
potentially explosive atmospheres.
All equipment must be grounded.
4.1 Location
The pump should be located to allow roomfor
access, ventilation, maintenance and inspection
with ample headroom for lifting and should be as
close as practicable to the supply of liquid to be
pumped.
4.2 Foundation
There are many methods of
installing pump units to their foundations. The
correct method depends on the size of the pump
unit, its location and noise vibration limitations.
Non-compliance with the provision of correct
foundation and installation may lead to failure of
the pump and, as such, would be outside the
terms of the warranty.
The base plate should be mounted onto a firm
foundation, either an appropriate thickness of
quality concrete or sturdy steel framework.
It should NOT be distorted or pulled down onto the
surface of the foundation, but should be supported
to maintain the original alignment.
Anchor bolts must be in accordance with the foot
bolt holes. Use anchor bolts of accepted standards
and sufficient to ensure a secure fitting in the
foundation.
Particularly, this applies to individual plates where
the anchor bolts have to withstand the driving
torque.
NF E 27 811
Provide sufficient space in the foundation to
accommodate the anchor bolts. If necessary,
provide concrete risers.
Usually the pump and its drive are mounted on a
common base plate. If not, individual base plates
underneath each machine foot shall be installed.
Base plates are to be fully grouted.
4.2.1 Setting the base plate for anchoring
a) Clean the foundation surface thoroughly.
b) Put shims on the foundation surface [approx
20-25 mm (0.79-0.98 in.) thick], one oneach
side of the bolt hole (as an alternative, leveling
screws can be used).
c) Lay the base plate and level in both directions
with extra shims. The base plate should be
level to within 0.5 mm per 1 m(0.02 in. per 3.3
ft).
d) If anchor bolts have been pre-cast in the
foundation slightly tighten the anchor bolts.
Otherwise let them hang in the foundation
holes.

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 14 of 28 flowserve.com
4.3 Grouting
4.3.1 Base plate grouting
a) Prepare the site for grouting. Before grouting
clean the foundation surface thoroughly and
provide external barriers as shown:
b) Prepare grouting product (concrete, resin) in
accordance with manufacturers' instructions.
c) Use grouting products with anti-shrinking
components.
d) To grout up to the required level. Polish
surfaces. Take necessary precautions to avoid
air bubbles.
e) Lay-down the barrier, break external angles,
and polish the different surfaces.
f) After grout starts to cure, definitively tighten
anchor bolts.
g) Control the alignment such as described as
follows.
4.4 Initial alignment
Before connecting the couplings
verify the motor rotation direction.
4.4.1 Thermal expansion
The pump and motor will normally
have to be aligned at ambient temperature and
should be corrected to allow for thermal expansion
at operating temperature. In pump installations
involving high liquid temperatures, the unit should
be run at the actual operating temperature, shut
down and the alignment checked immediately.
4.4.2 Alignment methods
Ensure pump and driver are isolated
electrically and the half couplings are
disconnected. Ensure that the pump pipework,
suction and discharge, is disconnected.
The alignment MUST be checked.
Although the pump will have been aligned at the
factory it is most likely that this alignment will have
been disturbed during transportation or handling. If
necessary, align the motor to the pump, not the
pump to the motor.
Alignment
Parallelism and concentricity check:
Check the alignment at three or
four points, before piping assembly.
witha rule with a comparator
Admissible margin for a motor with roller bearings
with European couplings:
= 0.15 mmparallel checking
= 0.1 mm angular checking
For US supplied couplings values to be used are:
= 0.02 in. parallel checking
= 0.05 in. angular checking
Check the couplings manual for further details.
Angular checking:
with a sliding rule with a caliper gauge
The alignment will be definitive only
after pipe connection (see § 4.5.4).
If necessary, improve the machine alignment:
 Complete unit mounted on common base plate:
The machines are first aligned accurately in our
workshops. Usually, any misalignment observed
on site is due to a wrong adjustment under the
base plate (disturbed during transport or because
of forces exerted by the piping).

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 15 of 28 flowserve.com
It is only necessary to rectify the adjustment under
base plate. If it proves to be insufficient, modify the
motor and the piping.
 Pump and motor mounted on individual base
plates:
Machines are (or must be) first mounted on their
own base plate in the workshop. Once the pump is
set, it will be regarded as the fixed piece. Any
alignment necessary shall be carried out on the
motor.
Never connect the electric motor
before the setting has been completely finished.
4.5 Piping
The user must verify that the equipment is
isolated from any external sources of vibration.
Protective covers are fitted to the
pipe connections to prevent foreign bodies
entering during transportation and installation.
Ensure that these covers are removed from the
pump before connecting any pipes.
4.5.1 Suction and discharge piping
The dimensions of the pipes do not directly
depend on suction and discharge diameters of the
pump:
a) First, choose a flow speed < 2 m/s (7 ft/s) at
suction, and about 3 m/s (10 ft/s) at discharge.
b) Take into account the available NPSH, which
must be superior to the required NPSH of the
pump.
Never use pump as a support for
piping.
Do not mount expansion joints in
such a way that their force, due to internal
pressure, may act on the pump flange.
Maximumforces and moments allowed on the
pump flanges vary with the pump size and type.
These external strains may cause misalignment,
hot bearings, worn couplings, vibrations and the
possible failure of the pump casing.
When designing the pipes (§ 4.5.2.1, § 4.5.2.2, §
4.5.3.1) take necessary precautions in order not to
exceed maximum allowed strains.
Forces and moments applied to the pump flanges
must never exceed the values shown in the
following table:
Forces
Suction
DNA
Discharge
DNR Fv
max Fh max
Moments
Mt max
Pump type mm
(in.) mm (in.) daN (lbf) daN (lbf) m.daN (lbf.ft)
MHP-TN
100-65-315 100 (4”) 65 (2”1/2) 140 (315) 105 (236) 27 (199)
MHP-TN
125-100-315 125 (5”) 100 (4”) 180 (405) 125 (281) 47 (347)
Forces and moments values are applied to the
whole flanges and not flange-by-flange. For their
sharing out on the pump flanges, refer to standard
NFCR 13 931.
Ensure piping and fittings are
flushed before use.
Ensure piping for hazardous liquids is
arranged to allow pump flushing before removal of
the pump.
4.5.2 Suction piping
4.5.2.1 Design of a flooded suction line
The suction line must be as short and direct as
possible, never mount an elbow directly on the
inlet flange of the pump.
Valve
Non return valve
CouplingCoupling guard
Moto
r
Baseplate
Continuous
flow valve
Flooded suction configuration
a) Avoid sharp elbows or sudden narrowing. Use
convergent 20° (total angle).
b) Arrange the piping so that there are no air
pockets (no bulges).

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 16 of 28 flowserve.com
c) If high points cannot be avoided in suction line,
provide them with air relief cocks.
d) If a strainer is necessary, its net area should
be three or four times the area of the suction
pipe.
e) If an inlet valve is necessary, choose a model
with direct crossing.
Do not tighten flanges before the
final check (see § 4.5.4).
4.5.2.2 Design of a suction lift line
The inlet pipe must be as short and as direct as
possible, never place an elbow directly on the
pump inlet nozzle.
I
Sufficient
immersion
D
I3 x D
Sump suction configuration
a) Avoid sharp elbows or sudden narrowing. Use
convergent 20° (total angle) with upright
generating.
b) Arrange that the suction piping is inclined
upwards towards the pump ensuring that there
are no peaks.
c) If a foot valve is necessary, do not oversize it
because it would generate pulsations (valve
beating).
Do not tighten flanges before the
final check (see § 4.5.4).
4.5.3 Discharge piping
4.5.3.1 Design of a discharge line
a) If discharge line is provided with a divergent,
its total angle will be between 7° and 12°.
b) Install the discharge valve after the non-return
valve downstream.
The non-return valve will be set in the discharge
pipe to protect the pump from any excessive
pressure surge and from reverse rotation.
If necessary, a control manometer (pressure
gauge) can be connected on the piping.
Control manometer
Do not tighten flanges before the
final check (see § 4.5.4).
4.5.4 Final checks
a) Check the tightening of anchor bolts. Tighten
them if necessary.
b) Check that protective covers on suction and
discharge flanges are removed.
c) Check that holes of piping flanges are parallel
and correspond to those of the pump.
d) Tighten suction and discharge flanges.
4.6 Electrical connections
Electrical connections must be made
by a qualified Electrician in accordance with
relevant local national and international
regulations. This includes any grounding.
It is important to be aware of the
EUROPEAN DIRECTIVE on potentially explosive
areas where compliance with IEC60079-14 is an
additional requirement for making electrical
connections.
Avoid mechanical, hydraulic or electrical
overload by using motor overload trips or a power
monitor and make routine vibration monitoring.
It is important to beawareof theEUROPEAN
DIRECTIVE on electromagnetic compatibility when
wiringupandinstallingequipment on site.Attention
must be paidtoensure that the techniques used
duringwiring/installation do not increase
electromagnetic emissions or decrease the
electromagnetic immunity of the equipment, wiringor
any connected devices. If in doubt, contact
Flowserve foradvice.
The motor must be wired up in
accordance with the motor manufacturer's
instructions (normally supplied within the terminal
box) including any temperature, earth leakage,
current and other protective devices as
appropriate.

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 17 of 28 flowserve.com
The identification nameplate should be checked to
ensure the power supply is appropriate. A device
to provide emergency stopping shall be fitted.
Carry out the ground connections according to the
current local regulations.
To avoid any risk of jamming, the
direction of rotation will be checked after priming of
the pump (§ 5.3.1, 5.3.2) and before the first start
(§ 5.4.2).
4.7 Final shaft alignment check
a) Check the alignment pump-motor according to
the procedure § 4.4.2. Rectify if necessary by
adjusting the motor only.
b) Check by hand that the pump turns freely.
A binding indicates a distortion of the pump,
which is due to excessive pipe strain. If
necessary the pipe design must be re-
examined.
c) If it provided, connect auxiliary pipe systems
(hydraulic, pneumatic, sealing system).
d) Control tightness and functionality of auxiliary
piping.
4.8 Protection systems
The following protection systems are
recommended particularly if the pump is installed
in a potentially explosive area or is handling a
hazardous liquid. If in doubt consult Flowserve.
If there is any possibility of the system allowing the
pump to run against a closed valve or below
minimum continuous safe flow a protection device
should be installed to ensure the temperature of
the liquid does not rise to an unsafe level.
If there are any circumstances in which the system
can allow the pump to run dry, or start up empty, a
power monitor should be fitted to stop the pump or
prevent it from being started. This is particularly
relevant if the pump is handling a flammable liquid.
If leakage of product from the pump or its
associated sealing system can cause a hazard it is
recommended that an appropriate leakage
detection system is installed.
To prevent excessive surface temperatures at
bearings it is recommended that temperature or
vibration monitoring are carried out. See sections
5.5.3 and 5.5.4.
If a defect of cooling can lead to temperature
higher than those acceptable a systemof cooling
surveillance must be installed.
Except when explicitly required by the customer in
the specifications, when a possibility of reverse
rotation exists the customer must install a reverse
rotation protection device.
The customer must install all equipment required
to avoid water hammer.
5 COMMISSIONING, START-UP,
OPERATION AND SHUTDOWN
These operations must be carried out by
fully qualified personnel.
5.1 Direction of rotation
Starting or operating pumps with
the wrong direction of rotation can be harmful to
the pumps. Ensure that the pump rotation is the
same as the arrow on the pump casing. It is
preferable to check the direction of rotation before
installing the coupling. If not, the pump must be
filled in with the liquid before start-up.
If maintenance work has been
carried out to the site's electricity supply, the
direction of rotation should be re-checked as
above in case the supply phasing has been
altered.
5.2 Guarding
Guarding is supplied fitted to the pump set.
If this has been removed or disturbed ensure that
all the protective guards around the pump coupling
and exposed parts of the shaft are securely fixed.
5.3 Priming and auxiliary supplies
Where there is any risk of the pump being
run against a closed valve generating high liquid
and casing external surface temperatures it is
recommended that users fit an external surface
temperature protection device.
Ensure all electrical, hydraulic,
pneumatic, sealant and lubricationsystems (as
applicable) are connected and operational.
Ensure the inlet pipe and pump
casing are completely full of liquid before starting
continuous duty operation.
These operations must be carried out by personnel
with approved qualifications.

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 18 of 28 flowserve.com
5.3.1 Priming of a flooded pump
a) As discharge valve is closed, fill the pump by
opening the valve at suction. Let air escape by
removing the plugs located on the pump.
b) The discharge pipe is headed and there is a
by-pass valve on the check valve, open
slightly the discharge valve and the by-pass of
the check valve.
c) When the pump is totally free of air bubbles,
replace the plugs.
Air escape
Priming of a flooded pump
5.3.2 Priming of a sump suction pump
* With foot valve:
a) Fill suction pipe and casing with liquid from an
independent source (pressure 1 to 2 bars or
15 to 30 psi).
b) Let air escape by removing the plugs located
on the pump.
c) When the pump is totally free of air bubbles,
replace the plugs.
External source
Air escape
Priming of sump suction pump with foot valve
*Without foot valve:
Priming may be accomplished by means of venting
system.
Foot valves are not recommended when
the pumped liquid has suspended solid particles.
They may lodge between foot valve seat and
shutter.
5.4 Starting the pump
5.4.1 Bring controls and preparation before the
first starting and after each service call
Necessarily:
a) Check the tightening of the different plugs.
b) Check that the gland lightly tightens the
packing rings.
c) Risk of seal ring overheating.
d) Check the direction of rotation of the motor.
Refer to the rotation arrow of the pump.
e) Install all protection systems and more
particularly the coupling guard and the shield
grid (reference [9331]) of the bearing.
f) Open all suction valves (if existing).
g) Close the outlet valve and the bypass valve.
h) Ensure inlet pipe and pump casingare
completely full of liquid.
5.4.2 First pump start-up
Suction valves must be fully open
when pump is running. Never run the pump dry, it
will cause damage.
a) Start motor and check outlet pressure.
b) If pressure is satisfactory, slowly OPEN outlet
valve.
c) Do not run the pump with the outlet valve
closed for a period longer than 30 seconds.
d) If NO pressure, or LOW pressure, STOP the
pump. Refer to faultfinding chart for fault
diagnosis.
The pump should run smoothly and without
vibration.
The pump must never run at a capacity of less
than 40 % of that at the best efficiency.
Never remove a plug when the pump is
running.

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 19 of 28 flowserve.com
5.5 Running the pump
5.5.1 Venting the pump
Vent the pump to enable all trapped air to
escape taking due care with hot or hazardous
liquids.
Under normal operating conditions, after the pump
has been fully primed and vented, it should be
unnecessary to re-vent the pump.
5.5.2 Pump fitted with a stuffing box
If the pump has a packed gland there must be
some leakage from the gland. Gland nuts should
initially be finger tight only. Leakage should take
place soon after the stuffing box is pressurized. If
no leakage takes place the packing will begin to
overheat. If overheating takes place the pump
should be stopped and allowed to cool before
being restarted. When the pump is restarted it
should be checked to ensure leakage is taking
place at the packed gland.
When adjusting an operating stuffing box
(shield grids removed for this operation), the
operator must be very careful. Safety gloves are
compulsory and loose clothes are not allowed
(above all to the arms) to avoid being caught by
the pump shaft.
The pump should be run for ten minutes with
steady leakage and the gland nuts tightened by 10
degrees at a time until leakage is reduced to an
acceptable level.
The temperature of the gland should be checked
after each round of tightening. If the temperature
starts to climb rapidly then back off the gland nuts
until the temperature drops down. Wait for the
temperature to stabilize before tightening again.
The leakage must not be reduced below a rate of
20 drops per minute. Bedding in of the packing
may take several hours.
Shield grids being removed during
installation of the gland packing, it must be
ensured that they are replaced as soon as this
operation is completed.
SAFETY INSTRUCTIONS WHEN THE PUMP IS
RUNNING:
If hot or freezing components of the machine
can present a danger to operators, they must be
shielded to avoid accidental contact. If a 100 %
protection is not possible, the machine access
must be confined to the maintenance staff only.
If the temperature is greater than 80 °C (176
°F), a warning plate must be clearly placed on the
pump.
It is strictly forbidden to open switch
cupboards, switch boxes, or all other live electric
equipment. If it is necessary to open them in order
to take readings, to carry out tests or adjustments
for example, only a skilled technician may do them
with adapted tools. Make sure that physical
protection against electrical risks are used.
5.5.3 Bearings
If the pumps are working in a potentially
explosive atmosphere, temperature or vibration
monitoring at the bearings is recommended.
If bearing temperatures are to be monitored it is
essential that a benchmark temperature is
recorded at the commissioning stage and after the
bearing temperature has stabilized.
Record the bearing temperature (t) and the
ambient temperature (ta)
Estimate the likely maximum ambient
temperature (tb)
Set the alarm at (t+tb-ta+5) C [(t+tb-ta+10) F]
and the trip at 100 C (212 F) for oil
lubrication and 105 C (220 F) for grease
lubrication
It is important, particularly with grease lubrication,
to keep a check on bearing temperatures. After
start up the temperature rise should be gradual,
reaching a maximum after approximately 1.5 to 2
hours. This temperature rise should then remain
constant or marginally reduce with time.
5.5.4 Normal vibration levels, alarm and trip
For guidance, pumps generally fall under a
classification for rigid support machines within the
International rotating machinery standards and the
recommended maximum levels below are based
on those standards.
Alarmand trip values for installed
pumps should be based on the actual
measurements (N) taken on site on the bearing
housings of the pump in the fully commissioned as
new condition.

MHP-TN USER INSTRUCTIONS ENGLISH 71576313 -02/07
Page 20 of 28 flowserve.com
The example (N) value is given for the preferred
operating flow region (typically this may extend to
70 to 120 % of the pump best efficiency point);
outside the preferred flow region the actual
vibration experienced may be multiplied by up to 2.
These standard values can vary with the rotational
speed and the power absorbed by the pump. For
any specialcase, do not hesitate to consult us.
Measuring vibration at regular intervals will then
show any deterioration in pump or system
operating conditions.
Vibration Velocity - unfiltered Horizontal Configuration
mm/s (in./s) r.m.s.
Normal N5.6 (0.22)
Alarm Nx1.25 7.1 (0.28)
Shutdown Trip Nx 2.0 11.2 (0.44)
5.5.5 Stop/start frequency
Pump sets are normally suitable for the number of
equally spaced stop/starts per hour shown in the
table below. Check actual capability of the driver
and control/starting system before commissioning.
Motor rating kW (hp) Maximum stop/starts
per hour
Up to 15 (20) 15
Between 15 (20) and 90 (120) 10
90 (120) to 150 (200) 6
Above 150 (200) Refer
Where duty and standby pumps are installed it is
recommended that they are run alternately every
week.
5.6 Stopping and shutdown
According to hydraulic conditions of
the installation and its automation degree, stop
and restart procedures can have different forms.
Nevertheless all of them must respect imperatively
the following rules:
5.6.1 Stopping < 1 hour
a) Isolate motor.
b) Avoid reverse rotation of the pump.
c) Make sure that the discharge line pressure
does not reach the foot valve.
5.6.2 Stopping < 1 month
a) Isolate motor.
b) Avoid reverse rotation of the pump.
c) Make sure that the discharge line pressure
does not reach the foot valve.
d) Close the outlet valve. Eventually close the
inlet valve.
e) Switch off external power supply,
flushing/quench, cooling liquid.
5.6.3 Shutdown > 1month
a) Isolate motor.
b) Avoid reverse rotation of the pump.
c) Make sure that the discharge line pressure
does not reach the foot valve.
d) Close the outlet valve. Eventually close the
inlet valve.
e) Switch off external power supply,
flushing/quench, cooling liquid.
f) Keep the pump fully filled with water. In case
of pumped liquid other than water, drain the
pump entirely.
g) Turn once per week the pump shaft of one or
two turns.
h) Never restart the pump without carrying out
the verifications recommended before starting
(see § 5.4.1).
When ambient temperatures are
likely to drop below freezing point, the pump and
any cooling and flushing arrangements must be
drained or otherwise protected.
5.6.4 Restarting in continuous running
a) Ensure that the pump is completely full of
liquid.
b) Ensure a continuous supply with a sufficient
available NPSH.
c) Ensure a backpressure so that the motor
power is not in excess.
d) Respect the starting frequency
imposed by the motor manufacturer.
e) Protect the pump against water hammer
when stopping or starting.
5.7 Hydraulic, mechanical and
electrical duty
This product has been supplied to meet the
performance specifications of your purchase order,
however it is understood that during the life of the
product these may change. The following notes
may help the user decide how to evaluate the
implications of any change. If in doubt contact your
nearest Flowserve office.
5.7.1 Specific gravity (SG)
Pump capacity and total head in meters (feet) do
not change with SG, however pressure displayed
on a pressure gauge is directly proportional to SG.
Power absorbed is also directly proportional to SG.
It is therefore important to check that any change
in SG will not overload the pump driver or over-
pressurize the pump.
5.7.2 Viscosity
For a given flow rate the total head reduces with
increased viscosity and increases with reduced
viscosity.