Fluke Y5735 User manual

PN 802926 September 1988 Rev. 3, 1/16 ©1998 – 2016 Fluke Corporation. All rights reserved. 1
Y5735/Y5737/Y5320
Rack Mount Kit
Instruction Sheet
Introduction
This sheet provides instruction for mounting the
5320A Multifunction Calibrator, 5700A
Multifunction Calibrator, 5725A Amplifier, 5730A
Multifunction Calibrator, and 5790A/5790B AC
Measurement Standards into a standard
19.12-inch panel opening E.I.A. universal spacing
equipment rack. The Y5735 Rack Mount Kit is for the
5725A Amplifier. Kit contents and instructions for
installation are the same for both kits, except for the
size of the rack ears and usage of filler bar to slide rail
mounting holes.
WWarning
To prevent personal injury:
•Read all safety information before
you use the Product.
•Use the Product only as specified, or
the protection supplied by the
Product can be compromised.
•Use both lifting handles and good
lifting practice when lifing or
carrying any equipment to be
mounted in the rack.
Preparation
Before installing the rack mount kit, remove the top
and bottom screws from the sides of the front
instrument handles. Leave the center screws installed.
Remove the plastic filler strips from the sides of the
instrument by prying one end of each strip free using
a flat-head screwdriver.
Installation
To install a kit, proceed as follows:
1. Attach the rack ears to the instrument using two
#8-32 x ½” pan-head screws for each ear as
Figure 1 shows.
2. Install the filler bars on the sides of the instrument
using two #8-32 x ¼” truss-head machine screws
per bar as Figure 1 shows, making sure the first
tapped hole closest to the end of the bar is toward
the front of the instrument.
3. Pull the slide rails out from the rack slides and
push the stopper to fully detatch and disassemble
the rails.
4. Attach the slide rails to the filler bars using four
#8-32 x 3/8-inch pan flathead screws for each rail
as Figure 1 shows. Mount the 5730A, 5790A, and
5790B slide rail to the center row of holes. Mount
the 5725A slide rail to the lower row of holes.
(See Figure 1.)
5. Install the front slide brackets (shorter pair) to the
equipment rack mounting rails as Figure 2 shows.
(Refer to Figure 3 and 4 for typical mounting
holes spacing.) If your rack has threaded
mounting rails, use two #10-32 x ½” truss-head
screws as shown in Figure 2, Detail A. If your
rack has unthreaded mounting holes, use two #10-
24 x ½” truss-head screws and two #10-24 U-nuts
as shown in Figure 2, Detail B.
6. Install the rear slide bracket (longer pair) to the
equipment rack mounting brackets the same way
as the front.
7. Attach the slides to the front brackets using two
#8-32 x 3/8-inch flat Philips-head screws, two #8
flat washers, two #8 lock washers, and two #8
UNC hex nuts as Figure 2 shows. Align the slides
to the rear brackets the same way as the front,
except fully extend the slides to access the screw
heads.
8. Plug the instrument into the slides, unlock the
slides and push the instrument into the rack.
9. Secure the instrument to the rack by fastening the
rack ears to the mounting rails with two #10-32 x
¾” decorative-head screws per ear. If your rack
has unthreaded mounting rails, install two #10-32
U-nuts in appropriate places in the rail holes.

Note: Use center row for the
5320A, 730A, 5790A, and
5790B. Use lower row for the
5725A.
Filler Bar
Slide Rail
#8-32 x 1/4”
Panhead (2x)
#8-32 x 3/8”
Flat Phillips Head(4x)
#8-32 x 1/2” Panhead (2x)
Rack Ears (2x)
Figure 1. Attaching Hardware to the Instrument
Threaded Rack Holes use
#10-32 x 1/2” Truss Head Screws
Detail A
Unthreaded Rack Holes use
#10-24 U Nuts and
#10-24 x 1/2” Truss Head Screws
Detail B
#8 Flat Washers,
lock Washer,
and #8 Hex Nuts
Rear Slide
Bracket
Front Slide
Bracket
Mounting Hardware
(#8 steel)
#8-32 x .38 Flat Philips Head (x8)
#8-32 UNC Hex Nut (x8)
#8 Flat Washer (x8)
#8 Lock Washer (x8)
#8-32 x .38 Flat Philips Head
Figure 2. Installing Rack Slides

Rack Mount Kit
Installation
3
Equipment Mounting Rail
E.I.A. Universal Spacing Rack
typical 5725A instrument
mounting
Rack Ear
Rack Ear Mounting Hole to equipment rack
5725A Rack Ear Mounting Hole to equipment rack
Slide Bracket Mounting for 5725A
to Equipment Rack
0.625
0.625
0.625
0.625
0.625
0.500
0.625
0.500
0.500
Figure 3. Typical 5725A Mounting Locations
Equipment Mounting Rail
5320A, 5700A, 5730A, 5790A, 5790B Rack Ear
5320A, 5700A, 5730A, 5790A, 5790B
Rack Ear Mounting Hole
to Equipment Rack
5320A, 5700A, 5730A, 5790A, 5790B Rack Ear Mounting
Hole to Equipment Rack
Slide Bracket Mounting for 5320A, 5700A, 5730A, 5790A,
5790B to Equipment Rack
0.625
0.625
0.625
0.625
0.625
0.625
0.500
0.500
0.500
Figure 4. Typical 5320A, 5700A, 5730A, 5790A, 5790B Mounting Locations

Y5735/Y5737/Y5320
Instruction Sheet
4
Decorative Head, #10-32 x 3/4 in. U-Nut, #10-32
Hex- Nut, #8
Flat Washer, #8
Lock Washer, #8
U-Nut, #10-24
#8-32 x .38 Flat Philips Head
Truss-Head, #8-32 x 1/4 in.
Truss-Head, #10-32 x 1/2 in.
Truss-Head, #10-24 x 1/2 in.
Figure 5. Screw Identification