Fmi Gwrn18c Original instructions

For more information, visit www.fmiproducts.com

WARNING: If the information in this manual is not

followed exactly, a re or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re

department.

— Installation and service must be performed by a quali-

ed installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

UNVENTED (VENT-FREE) INFRARED GAS HEATER

SAFETY INFORMATION AND INSTALLATION MANUAL

MODELS

GWRP16C, GWRN18C, GWRP26C, GWRN30C,

GWRP16TC, GWRN18TC, GWRP26TC, GWRN30TC

VSHRP16M, VSHRP16T, VSHRN18M, VSHRN18T,

VSHRP26M, VSHRP26T, VSHRN30M, AND VSHRN30T

PFS

www.fmiproducts.com 125311-01A2

This appliance may be in-

stalled in an aftermarket,*

permanently located,

manufactured (mobile)

home, where not prohib-

ited by local codes.

* Aftermarket: Completion of sale, not for

purpose of resale, from the manufacturer

WARNING: This product con-

tains and/or generates chemicals

known to the State of California

to cause cancer or birth defects

or other reproductive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble,

operate or service this heater.

Improper use of this heater can

cause serious injury or death

from burns, fire, explosion,

electrical shock and carbon

monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs

of carbon monoxide poisoning resemble the

u, with headaches, dizziness or nausea. If

you have these signs, the heater may not be

working properly. Get fresh air at once! Have

heater serviced. Some people are more af-

fected by carbon monoxide than others. These

include pregnant women, people with heart or

lung disease or anemia, those under the inu-

ence of alcohol and those at high altitudes.

SAFETY

TABLE OF CONTENTS

Safety .................................................................. 2

Local Codes......................................................... 4

Product Identication ........................................... 4

Unpacking............................................................ 4

Product Features ................................................. 4

Air For Combustion and Ventilation ..................... 5

Installation ........................................................... 7

Operation ........................................................... 14

Inspecting Heater .............................................. 17

Cleaning and Maintenance ................................ 17

Specications .................................................... 18

Troubleshooting ................................................. 19

Parts .................................................................. 22

Accessories ....................................................... 27

Replacement Parts ............................................ 27

Service Publications .......................................... 27

Service Hints ..................................................... 27

Technical Service............................................... 27

Warranty ..............................................Back Cover

WARNING: Improper

installation, adjustment,

alteration,service or main-

tenance can cause injury

or property damage. Refer

to this manual for correct

installation and operation-

al procedures. For assis-

tance or additional infor-

mation consult a qualied

installer, service agency

or the gas supplier.

WARNING: This is an

unvented gas-red heat-

er. It uses air (oxygen)

from the room in which

it is installed. Provisions

for adequate combustion

and ventilation air must

be provided. Refer to Air

for Combustion and Ven-

tilation section on page 5

of this manual.

This appliance is only for

use with the type of gas

indicated on the rating

plate. This appliance is

not convertible for use

with other gases.

www.fmiproducts.com

125311-01A 3

Keep the appliance area clear

and free from combustible ma-

terials, gasoline and other am-

mable vapors and liquids.

1. This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with

other gases.

2. Do not place propane/LP supply tank(s)

inside any structure. Locate propane/LP

supply tank(s) outdoors.

3. This heater shall not be installed in a

bedroom or bathroom.

4. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from

a neighbor’s phone. Follow the gas sup-

plier’s instructions

• if you cannot reach your gas supplier,

call the re department

5. Manual Control Models Always run

heater with plaque control knob at the 1,

2, 3 or 4 locked positions. Never set con-

trol knob between locked positions. Poor

combustion and higher levels of carbon

monoxide may result.

6. This heater needs fresh, outside air ventila-

tion to run properly. This heater has an Oxy-

gen Depletion Sensing (ODS) safety shutoff

system. The ODS shuts down the heater if

not enough fresh air is available. See Air for

Combustion and Ventilation, page 5.

7. Keep all air openings in front and bottom

of heater clear and free of debris. This will

insure enough air for proper combustion.

8. If heater shuts off, do not relight until you

provide fresh, outside air. If heater keeps

shutting off, have it serviced.

9. Do not run heater

• where ammable liquids or vapors are

used or stored

• under dusty conditions

10. Do not use heater if any part has been

under water. Immediately call a qualied

service technician to inspect the room

heater and to replace any part of the

control system and any gas control which

has been under water.

Natural and Propane/LP Gas: Natural and

propane/LP gases are odorless. An odor-

making agent is added to these gases. The

odor helps you detect a gas leak. However, the

odor added to the gas can fade. Gas may be

present even though no odor exists.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this heater.

WARNING: Any change to

this heater or its controls can

be dangerous.

WARNING: Do not use a

blower insert, heat exchanger

insert or other accessory not ap-

proved for use with this heater.

Due to high temperatures, the

appliance should be located out

of trafc and away from furniture

and draperies.

Do not place clothing or other

ammable material on or near

the appliance. Never place any

objects on the heater.

Surface of heater becomes very

hot when running heater. Keep

children and adults away from

hot surface to avoid burns or

clothing ignition. Heater will

remain hot for a time after shut-

down. Allow surface to cool

before touching.

Carefully supervise young chil-

dren when they are in the room

with heater.

Make sure grill guard is in place

before running heater.

SAFETY

Continued

www.fmiproducts.com 125311-01A4

SAFETY

Continued

Figure 1 - Vent-Free Gas Heater

(actual heater may vary from illustration

14. Before using furniture polish, wax, carpet

cleaner or similar products, turn heater off.

If heated, the vapors from these products

may create a white powder residue within

burner box or on adjacent walls or furni-

ture.

15. Provide adequate clearances around air

openings.

11. Turn off and unplug heater and let cool

before servicing. Only a qualied service

person should service and repair heater.

12. Operating heater above elevations of

4,500 feet (1,371 m) could cause pilot

outage.

13. To prevent performance problems, do not

use propane/LP fuel tank of less than 100

lbs. (45 kg) capacity.

LOCAL CODES

Install and use heater with care. Follow all

local codes. In the absence of local codes,

use the latest edition of The National Fuel

Gas Code ANSI Z223/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

State of Massachusetts: The installa-

tion must be made by a licensed plumber

or gas fitter in the Commonwealth of

Massachusetts.

Sellers of unvented propane or natural

gas-red supplemental room heaters shall

provide to each purchaser a copy of 527

CMR 30 upon sale of the unit.

Vent-free gas products are prohibited for

bedroom and bathroom installation in the

Commonwealth of Massachusetts.

PRODUCT

IDENTIFICATION

UNPACkING

1. Remove heater from carton.

2. Remove all protective packaging applied

to heater for shipment.

3. Check heater for any shipping damage. If

heater is damaged call FMI PRODUCTS,

LLC at 1-866-328-4537 for replacement

parts before returning to dealer.

PRODUCT FEATURES

SAFETY DEVICE

This heater has a pilot with an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS/pilot is a required feature for vent-free

room heaters. The ODS/pilot shuts off the

heater if there is not enough fresh air.

IGNITION SYSTEM

Some models are equipped with a piezo

ignitor that requires no matches, batteries or

other sources to light heater.

Other heaters are equipped with an electronic

ignitor to light heater fuel supply.

THERMOSTATIC HEAT CONTROL

(Thermostat Models Only)

Thermostat models have a thermostat sens-

ing bulb and a control valve. This results in the

greatest heater comfort. This can also result

in lower gas bills.

Ignitor Button

Control Knob

Heater Cabinet

Front Panel

Plaque

Grill

Guard

www.fmiproducts.com

125311-01A 5

AIR FOR COMBUSTION AND VENTILATION

WARNING: This heater shall

not be installed in a room or space

unless the required volume of in-

door combustion air is provided

by the method described in the

National Fuel Gas Code, ANSI

Z223.1/NFPA 54, the International

Fuel Gas Code, or applicable lo-

cal codes. Read the following in-

structions to insure proper fresh

air for this and other fuel-burning

appliances in your home.

Today’s homes are built more energy efcient

than ever. New materials, increased insulation

and new construction methods help reduce

heat loss in homes. Home owners weather

strip and caulk around windows and doors to

keep the cold air out and the warm air in. Dur-

ing heating months, home owners want their

homes as airtight as possible.

While it is good to make your home energy

efcient, your home needs to breathe. Fresh

air must enter your home. All fuel-burning ap-

pliances need fresh air for proper combustion

and ventilation.

Exhaust fans, heaters, clothes dryers and fuel

burning appliances draw air from the house to

operate. You must provide adequate fresh air

for these appliances. This will insure proper

venting of vented fuel-burning appliances.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel

Gas Code. ANSI Z223.1/NFPA 54, Air for

Combustion and Ventilation.

All spaces in homes fall into one of the three

following ventilation classications:

1. Unusually Tight Construction

2. Unconned Space

3. Conned Space

The information on pages 5 through 7 will

help you classify your space and provide

adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and windows

may provide enough fresh air for combustion

and ventilation. However, in buildings of un-

usually tight construction, you must provide

additional fresh air.

Unusually tight construction is dened as

construction where:

a. walls and ceilings exposed to the out-

side atmosphere have a continuous

water vapor retarder with a rating of

one perm (6x10-11 kg per pa-sec-m2) or

less with openings gasketed or sealed

and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to

areas such as joints around window

and door frames, between sole plates

and oors, between wall-ceiling joints,

between wall panels, at penetrations

for plumbing, electrical and gas lines

and at other openings.

If your home meets all of the three criteria

above, you must provide additional fresh air.

See Ventilation Air From Outdoors, page 7.

If your home does not meet all of the three

criteria above, proceed to Determining

Fresh-Air Flow For Heater Location.

Conned Space and Unconned Space

The National Fuel Gas Code ANSI Z223.1/

NFPA 54 denes a conned space as a space

whose volume is less than 50 cubic feet per

1,000 Btu per hour (4.8 m3 per kw) of the ag-

gregate input rating of all appliances installed

in that space and an unconned space as a

space whose volume is not less than 50 cubic

feet per 1,000 Btu per hour (4.8 m3 per kw)

of the aggregate input rating of all appliances

installed in that space. Rooms communicating

directly with the space in which the appliances

are installed*, through openings not furnished

with doors, are considered a part of the un-

conned space.

* Adjoining rooms are communicating only if

there are doorless passageways or ventilation

grills between them.

www.fmiproducts.com 125311-01A6

DETERMINING FRESH-AIR FLOW

FOR HEATER LOCATION

Determining if You Have a Conned or

Unconned Space

Use this work sheet to determine if you have

a conned or unconned space.

Space: Includes the room in which you will install

heater plus any adjoining rooms with doorless

passageways or ventilation grills between the

rooms.

1. Determine the volume of the space (length

x width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 20 ft. (6.1m) (length) x

16 ft. (4.88m) (width) x 8 ft. (2.44 m) (ceiling

height) = 2,560 cu. ft. (72.49 m2)(volume of

space)

If additional ventilation to adjoining room

is supplied with grills or openings, add the

volume of these rooms to the total volume

of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example: 2,560 cu. ft. (72.49 m2) (volume of

space) x 20 = 51,200 (maximum Btu/Hr the

space can support)

3. Add the Btu/Hr of all fuel burning appliances

in the space.

Vent-free heater _________ Btu/Hr

Gas water heater* _________ Btu/Hr

Gas furnace _________ Btu/Hr

Vented gas heater _________ Btu/Hr

Gas heater logs _________ Btu/Hr

Other gas appliances* + _________ Btu/Hr

Total = _________ Btu/Hr

* Do not include direct-vent gas appliances.

Direct-vent draws combustion air from the

outdoors and vents to the outdoors.

Example:

Gas water heater _________ Btu/Hr

Vent-free heater + _________ Btu/Hr

Total = _________ Btu/Hr

4. Compare the maximum Btu/Hr the space

can support with the actual amount of Btu/

Hr used.

_______ Btu/Hr (maximum can support)

_______ Btu/Hr (actual amount used)

Example: 51,200 Btu/Hr (maximum the

space can support)

60,000 Btu/Hr (actual amount of

Btu/Hr used)

AIR FOR COMBUSTION AND VENTILATION

Continued

The space in the example is a conned space

because the actual Btu/Hr used is more than the

maximum Btu/Hr the space can support. You

must provide additional fresh air. Your options

are as follows:

A. Rework worksheet, adding the space of an

adjoining room. If the extra space provides an

unconned space, remove door to adjoining

room or add ventilation grills between rooms.

See Ventilation Air From Inside Building.

B. Vent room directly to the outdoors. See

Ventilation Air From Outdoors, page 7.

C. Install a lower Btu/Hr heater, if lower Btu/Hr

size makes room unconned.

If the actual Btu/Hr used is less than the maxi-

mum Btu/Hr the space can support, the space is

an unconned space. You will need no additional

fresh air ventilation.

WARNING:Iftheareainwhich

the heater may be operated does

not meet the required volume for

indoor combustion air, combus-

tion and ventilation air shall be

provided by one of the methods

described in the National Fuel

Gas Code,ANSI Z223.1/NFPA 54,

the International Fuel Gas Code,

or applicable local codes.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining

unconned space. When ventilating to an

adjoining unconned space, you must provide

two permanent openings: one within 12" (30.5

cm) of the ceiling and one within 12" (30.5 cm)

of the oor on the wall connecting the two

spaces (see options 1 and 2, Figure 2, page

7). You can also remove door into adjoining

room (see option 3, Figure 2, page 7). Follow

the National Fuel Gas Code, ANSI Z223.1/

NFPA 54, Air for Combustion and Ventilation

for required size of ventilation grills or ducts.

40,000

60,000

20,000

www.fmiproducts.com

125311-01A 7

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills

or ducts. You must provide two permanent

openings: one within 12" (30.5 cm) of the ceil-

AIR FOR COMBUSTION AND VENTILATION

Continued

Figure 2 - Ventilation Air from Inside

Building

Figure 3 - Ventilation Air from Outdoors

ing and one within 12" (30.5 cm) of the oor.

Connect these items directly to the outdoors

or spaces open to the outdoors. These spaces

include attics and crawl spaces. Follow the Na-

tional Fuel Gas Code, ANSI Z223.1/NFPA 54,

Air for Combustion and Ventilation for required

size of ventilation grills or ducts.

IMPORTANT: Do not provide openings for inlet

or outlet air into attic if attic has a thermostat-

controlled power vent. Heated air entering the

attic will activate the power vent.

INSTALLATION

NOTICE: This heater is intended

for use as supplemental heat.

Use this heater along with your

primary heating system. Do not

install this heater as your pri-

mary heat source. If you have a

central heating system, you may

run system’s circulating blower

while using heater. This will help

circulate the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

WARNING: A qualied ser-

vice person must install heater.

Follow all local codes.

WARNING: This appliance is

equipped for either natural gas or

propane/LP gas but not both. Gas

type is indicated on the rating plate.

Field conversion is not permitted.

CHECK GAS TYPE

Use only the correct gas type (natural

or propane/LP) for your unit. If your gas

supply is not correct, do not install heater.

Call dealer where you bought heater for

proper type heater.

INSTALLATION ITEMS

Before installing heater, make sure you have

the items listed below.

• for propane/LP gas, external regulator

(supplied by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• ground joint union

• sediment trap

• tee joint

• pipe wrench

• for natural gas, test gauge connection*

• hardware packet (included)

- wall anchor (4) 095112-02

- red key (1) 095116-01

- pan head screw, black (4) 097403-02

- nylon spacer (2) 099064-02

- clip (1) 099123-01

- Phillips head screw, silver (4) 100159-02

* An equipment shutoff valve with 1/8" NPT tap

is an acceptable alternative to test gauge con-

nection. The optional equipment shutoff valve

can be purchased from your dealer.

Remove

Door into

Adjoining

Room,

Option 3

Ventilation Grills

Into Adjoining Room,

Option 2

12"

Ventilation

Grills into

Adjoining

Room,

Option 1

Outlet

Air

Ventilated

Attic

Outlet

Air

Inlet

Air

Inlet Air Ventilated

Crawl Space

Crawl

Space

To Attic

www.fmiproducts.com 125311-01A8

LOCATING HEATER

This heater is designed to be mounted on a wall.

WARNING: Maintain the

minimum clearances shown

in Figure 4. If you can, provide

greater clearances from oor,

ceiling and joining wall.

You can locate heater on oor, away from

a wall. An optional oor mounting stand is

needed. Purchase the oor mounting stand

from your dealer. See Accessories, page 27,

if stand is not included with your heater.

WARNING: Never install the

heater

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture, cloth-

ing or other ammable objects

are less than 36" (91.5 cm)

from the front, top or sides of

the heater

• as a replace insert

• in high trafc areas

• in windy or drafty areas

CAUTION: If you install the

heater in a home garage

• heater pilot and burner must

be at least 18" (45.7 cm) above

oor

• locate heater where moving

vehicle will not hit it

CAUTION: This heater cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to heater. Installing

heater next to vinyl or cloth wall

coverings or operating heater

where impurities (such as, but

not limited to, tobacco smoke,

aromatic candles, cleaning uids,

oil or kerosene lamps, etc.) in the

air exist, may discolor walls or

cause odors.

Figure 4 - Mounting Clearances As

Viewed From Front of Heater

Figure 5 - Attaching Thermostat Sensing

Bulb

INSTALLATION

Continued

Minimum

From

Sides Of

Heater

2" (5.1 cm)

FLOOR

CEILING

36"

(91.5 cm)

Minimum

Minimum To

Top Surface

Of Carpeting,

Tile Or Other

Combustible

Material

Left

Side

Right

Side

10" (25.4 cm)

36"

(91.5 cm)

Clip

Thermostat

Sensing

Bulb

IMPORTANT: Vent-free heaters add moisture

to the air. Although this is benecial, installing

heater in rooms without enough ventilation

air may cause mildew to form from too much

moisture. See Air for Combustion and Ventila-

tion, page 5. If high humidity is experienced,

a dehumidier may be used to help lower the

water vapor content in the air.

For convenience and efciency, install heater

• where there is easy access for operation,

inspection and service

• in coldest part of room

If not included with your heater, an optional fan

kit is available from your dealer. See Acces-

sories, page 27. If planning to use fan, locate

heater near an electrical outlet (see page 16).

THERMOSTAT SENSING BULB

(Thermostat Models Only)

The thermostat sensing bulb has been placed

below the heater.

1. Place clip on thermostat sensing bulb as

shown in Figure 5. Clip is provided in hard-

ware package.

2. Snap clip into upper mounting hole as shown

in Figure 5. Mounting hole is located on lower

left edge on back of heater. Make sure ther-

mostat sensing bulb is pointing up.

www.fmiproducts.com

125311-01A 9

INSTALLATION

Continued

Figure 6 - Mounting Bracket

Figure 8 - Mounting bracket Clearances

Figure 7 - Removing Front Panel of Heater

(actual heater may vary from Illustration)

INSTALLING HEATER TO WALL

Mounting Bracket

Locate mounting bracket in heater carton. Re-

move mounting bracket from heater carton.

Removing Front Panel Of Heater

1. Remove the four painted screws, two on

each side of front panel.

2. Pull bottom of front panel forward, then out.

3. Remove any remaining packaging materials.

Screw

Front Panel

Methods For Attaching Mounting Bracket

To Wall

Only use last hole on each end of mounting

bracket to attach bracket to wall. These two

holes are 14" (35.6 cm) apart from their cen-

ters. Attach mounting bracket to wall in one

of two ways:

1. Attaching to wall stud

2. Attaching to wall anchor

Attaching to Wall Stud: This method pro-

vides the strongest hold. Insert mounting

screws through mounting bracket and into

wall studs.

Attaching to Wall Anchor: This method al-

lows you to attach mounting bracket to hollow

walls (wall areas between studs) or to solid

walls (concrete or masonry).

Decide which method better suits your needs.

Either method will provide a secure hold for

the mounting bracket.

MARKING SCREW LOCATIONS

1. Tape mounting bracket to wall where

heater will be located. Make sure mount-

ing bracket is level.

WARNING: Maintain minimum

clearances shown in Figure 8. If

you can, provide greater clearanc-

es from oor and joining wall.

2. Mark screw locations on wall (see Figure 8).

Note: Only mark last hole on each end of

mounting bracket. Insert mounting screws

through these holes only.

3. Remove tape and mounting bracket from wall.

16"

Min.

14"

12"

Min.

Adjoining Wall

14"

Adjoining Wall

Only Insert Mounting

Screws Through Last

Hole On Each End

Only Insert Mounting

Screws Through Last

Hole On Each End

Floor

19 3/4"

Min.

19 3/4"

Min.

5 Plaque Heaters

3 Plaque Heater

Attaching Mounting Bracket To Wall

Note: Wall anchors, mounting screws and

spacers are in hardware package. The hard-

ware package is provided with heater.

Attaching To Wall Stud Method

For attaching mounting bracket to wall studs

1. Drill holes at marked locations using 9/64"

drill bit.

2. Place mounting bracket onto wall. Line

up last hole on each end of bracket with

holes drilled in wall.

3. Insert mounting screws through bracket

and into wall studs.

4. Tighten screws until mounting bracket is

rmly fastened to wall studs.

www.fmiproducts.com 125311-01A10

INSTALLATION

Continued

Figure 9 - Folding

Anchor

Figure 11 - Mounting Heater onto

Mounting Bracket

Figure 10 - Popping

Open Anchor Wings

for Thin Walls

Figure 12 - Installing Bottom Mounting

Screws

Attaching To Wall Anchor Method

For attaching mounting bracket to hollow

walls (wall areas between studs) or solid walls

(concrete or masonry)

1. Drill holes at marked locations using

5/16" drill bit. For solid walls (concrete or

masonry), drill at least 1" (2.5 cm) deep.

2. Fold wall anchor as shown in Figure 9.

3. Insert wall anchor (wings rst) into hole.

Tap anchor ush to wall.

4. For thin walls [1/2" (1.3 cm) or less], insert

red key into wall anchor. Push red key to

“pop” open anchor wings. IMPORTANT:

Do not hammer key! For thick walls [over

1/2" (1.3 cm) thick] or solid walls, do not

pop open wings.

5. Place mounting bracket onto wall. Line up

last hole on each end of bracket with wall

anchors.

6. Insert mounting screws through bracket

and into wall anchors.

7. Tighten screws until mounting bracket is

rmly fastened to wall.

Placing Heater On Mounting Bracket

1. Locate two horizontal slots on back panel

of heater.

2. Place heater onto mounting bracket. Slide

horizontal slots onto stand-out tabs on

mounting bracket.

Mounting

Bracket

(attached

to wall)

Horizontal Slots

Stand-Out Tab

Installing Bottom Mounting Screws

1. Locate two bottom mounting holes. These

holes are near bottom on back panel of

heater (see Figure 12).

2. Mark screw locations on wall.

3. Remove heater from mounting bracket.

4. If installing bottom mounting screws into

hollow or solid wall, install wall anchors.

Follow steps 1 through 4 under Attaching

To Wall Anchor Method.

If installing bottom mounting screw into

wall stud, drill holes at marked locations

using 9/64" drill bit.

5. Replace heater onto mounting bracket.

6. Place spacers between bottom mounting

holes and wall anchor or drilled hole.

7. Hold spacer in place with one hand. With

other hand, insert mounting screw through

bottom mounting hole and spacer. Place

tip of screw in opening of wall anchor or

drilled hole.

8. Tighten both screws until heater is rmly

secured to wall. Do not over tighten.

Note: Do not replace front panel at this

time. Replace front panel after making

gas connections and checking for leaks

(see page 11).

Side View

Front View

Wall

Spacer

Heater

MOUNTING HEATER TO FLOOR

WITH OPTIONAL FLOOR KIT

Mounting Base Feet to Heater

Note: A 90° elbow is required for mounting

this unit and must be installed BEFORE base

feet to provide proper clearance (see Figure

15, page 12).

1. Lay heater cabinet on its back on a table

with the heater bottom overhanging table

edge.

2. Apply pipe joint sealant lightly to male NPT

threads of elbow. Hold pressure regulator

with a wrench when connecting elbow.

Do not overtighten elbow to regulator.

Regulator body could be damaged.

www.fmiproducts.com

125311-01A 11

IMPORTANT: For natural gas, check gas line

pressure before connecting heater to gas line.

Gas line pressure must be no greater than

10.5" W.C.. If gas line pressure is higher,

heater regulator damage could occur.

CAUTION: For propane/LP

gas, never connect heater di-

rectly to the propane/LP supply.

This heater requires an external

regulator (not supplied). Install

the external regulator between the

heater and propane/LP supply.

For propane/LP gas, the installer must supply

an external regulator. The external regulator will

reduce incoming gas pressure. You must reduce

incoming gas pressure to between 11" and 14"

W.C.. If you do not reduce incoming gas pres-

sure, heater regulator damage could occur. Install

the external regulator with the vent pointing down

as shown in Figure 14. Pointing the vent down

protects it from freezing rain or sleet.

CAUTION: Use only new, black

iron or steel pipe. Internally-tinned

copper tubing may be used in

certain areas. Check your local

codes. Use pipe of large enough

diameter to allow proper gas vol-

ume to heater. If pipe is too small,

undue loss of volume will occur.

Typical Inlet Pipe Diameters

16-18,000 Btu/hr models - 3/8" or greater

26-30,000 Btu/hr models - 1/2" or greater

Installation must include equipment shutoff

valve, union and plugged 1/8" NPT tap. Locate

NPT tap within reach for test gauge hook up.

NPT tap must be upstream from heater (see

Figure 15, page 12).

Mounting Base Feet to Floor

1. Remove front panel (see Removing Front

Panel of Heater, page 9).

2. Position heater with base feet in desired

location. Mark holes for drilling. Remove

heater with base.

3. For carpeted oors, make a small cut with

a sharp knife at marked locations prior to

drilling. If mounting base to a wood oor,

drill 1/8" diameter hole, 3/4" deep. (Do not

use anchors in wood oors).

If mounting base to a concrete oor, drill with

1/4" diameter concrete drill bit, 13/8" into

oor. Insert anchors completely into holes.

4. Reposition heater with base feet over holes.

Secure base to oor with wood screws. See

Figure 13.

CONNECTING TO GAS SUPPLY

WARNING: This appliance

requires a 3/8" NPT (National

Pipe Thread) inlet connection to

the pressure regulator.

WARNING: A qualied service

person must connect heater to gas

supply. Follow all local codes.

WARNING: For natural gas, never

connect heater to private (non-utility)

gas wells. This gas is commonly

known as wellhead gas.

INSTALLATION

Continued

Propane/LP

Supply Tank

External

Regulator

with Vent

Pointing

Down

Figure 13 - Installing Base Feet (actual

heater may vary from illustration)

Figure 14 - Equipment Regulator with

Vent Pointing Down

3. Align holes in base foot with mounting holes

on bottom of cabinet (see Figure 13).

4. Secure base foot to heater using sheet

metal screws.

5. Repeat for other side.

Sheet

Metal

Screw

Wood

Screw

Base Foot

www.fmiproducts.com 125311-01A12

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping

and connections, internal and

external to unit, for leaks after

installing or servicing. Correct

all leaks at once.

WARNING: Never use an

open ame to check for a leak.

Apply a noncorrosive leak detec-

tion uid to all joints. Bubbles

forming show a leak. Correct all

leaks at once.

CAUTION: For propane/LP

units, make sure external regula-

tor has been installed between

propane/LP supply and heater.

See guidelines under Connecting

to Gas Supply, page 11.

PRESSURE TESTING GAS SUPPLY

PIPING SYSTEM

Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)

1. Disconnect appliance with its appliance

main gas valve (control valve) and equip-

ment shutoff valve from gas supply piping.

Pressures in excess of 1/2 psig will dam-

age heater regulator.

INSTALLATION

Continued

Figure 15 - Gas Connection

IMPORTANT: Install an equipment shutoff

valve in an accessible location. The equip-

ment shutoff valve is for turning on or shutting

off the gas to the appliance.

Check your building codes for an special

requirements for locating equipment shutoff

valve to heater.

Apply pipe joint sealant lightly to male NPT

threads. This will prevent excess sealant from

going into pipe. Excess sealant in pipe could

result in clogged heater valves.

Te e Pipe Cap

J oint Nipple

Tee Joint

Reducer

Bushing to

1/8" NPT

Plug Tap

Pressure

Regulator

Test Gauge Connection*

Heater

Cabinet

Sediment Trap

Min.

Natural Gas

From Gas

Meter (7" W.C.

to 10.5" W.C.

Pressure)

Propane/LP

From External

Regulator

(11" W.C. to 14"

W.C. Pressure)

Regulator

Bracket

Ground

Joint

Union

3/8" NPT

Pipe

Nipple

Equipment

Shutoff

Valve*

Connection Using Flexline

3/8" NPT/ 1/2"

Flare 90° Elbow

Flexline

See

illustration

above for

detail

Refer to connector's

instructions

* An equipment shutoff valve with 1/8" NPT

tap is an acceptable alternative to test gauge

connection. Purchase the optional equipment

shutoff valve from your dealer.

WARNING: Use pipe joint

sealant that is resistant to liquid

petroleum (LP) gas.

Install sediment trap in supply line as shown

in Figure 15. Locate sediment trap where it

is within reach for cleaning. Locate sediment

trap where trapped matter is not likely to

freeze. A sediment trap traps moisture and

contaminants. This keeps them from going

into heater controls. If sediment trap is not

installed or is installed wrong, heater may

not run properly.

IMPORTANT: Hold the pressure regulator with

wrench when connecting it to gas piping

and/or ttings. Do not over tighten pipe con-

nection to regulator. The regulator body could

be damaged.

www.fmiproducts.com

125311-01A 13

Equipment

Shutoff

Valve

Propane/LP

Supply Tank

Thermostat Gas Valve

Equipment

Shutoff

Valve

Gas

Meter

Thermostat Gas Valve

INSTALLATION

Continued

2. Cap off open end of gas pipe where equip-

ment shutoff valve was connected.

3. Pressurize supply piping system by either

opening propane/LP supply tank valve

for propane/LP gas or opening main gas

valve located on or near gas meter for

natural gas or using compressed air.

4. Check all joints of gas supply piping system.

Apply a commercial leak detection solution

to all joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Reconnect heater and equipment shutoff

valve to gas supply. Check reconnected

ttings for leaks.

Test Pressures Equal To or Less Than

1/2 PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Fig-

ure 16).

2. Pressurize supply piping system by either

opening propane/LP supply tank valve

for propane/LP gas or opening main gas

valve located on or near gas meter for

natural gas or using compressed air.

3. Check all joints from gas meter for natural

gas (see Figure 17)) or propane/LP supply

to equipment shutoff valve (see Figure

18). Apply a noncorrosive leak detection

uid to all joints. Bubbles forming show a

leak.

4. Correct all leaks at once.

PRESSURE TESTING HEATER GAS

CONNECTIONS

1. Open equipment shutoff valve (see Figure

16).

Figure 17 - Checking Gas Joints for

Natural Gas (actual heater may vary from

illustration)

Figure 18 - Checking Gas Joints for

Propane/LP Gas (actual heater may vary

from illustration)

Open

Closed

Equipment

Shutoff Valve

Figure 16 - Equipment Shutoff Valve

2. For natural gas, open main gas valve lo-

cated on or near gas meter. For propane/

LP gas, open propane/LP supply tank

valve.

3. Make sure control knob of heater is in the

OFF position.

4. Check all joints from equipment shutoff

valve to thermostat gas valve (see Figure

17 or 18). Apply a noncorrosive leak de-

tection uid to all joints. Bubbles forming

show a leak.

5. Correct all leaks at once.

6. Light heater (see Operation page 14).

Check all other internal joints for leaks.

7. Turn off heater (see To Turn Off Gas to

Appliance, page 15).

8. Replace front panel.

www.fmiproducts.com 125311-01A14

OPERATION

in the safety information, column 1. If you

don’t smell gas, go to the next step.

6. Thermostat Models: Turn control knob

counterclockwise to the PILOT

position. Press in control knob for ve (5)

seconds.

Manual Models: Press in and turn control

knob counterclockwise to the PILOT

position. Keep control knob pressed in for

ve (5) seconds.

7. With control knob pressed in, push down

and release ignitor button. This will light

pilot. The pilot is attached to the front of

burner. Note: You may be running this

heater for the rst time after hooking up to

gas supply. If so, you may need to press

in control knob for 30 seconds or more.

This will allow air to bleed from the gas

system. If needed, keep pressing ignitor

button until pilot lights. If ignitor does not

light pilot, refer to Troubleshooting, page

18 or contact a qualied service person

or gas supplier for repairs. Until repairs

are made, light pilot with match. To light

pilot with match, see Manual Lighting

Procedure, page 16.

8. Keep control knob pressed in for 30 sec-

onds after lighting pilot. After 30 seconds,

release control knob.

• If control knob does not pop out when

released, contact a qualied service per-

son or gas supplier for repairs.

Note: If pilot goes out, repeat steps 4

through 7. Wait one (1) minute before

lighting pilot

9. Turn control knob counterclockwise

to desired heating level. The main burner

should light. Manual control heaters

should be used in locked positions.

Figure 20 - Control Knob in the OFF

Position for Thermostat Models

Figure 19 - Control Knob in the OFF

Position for Manual Control Models

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not fol-

low these instructions exactly,

a re or explosion may result

causing property damage, per-

sonal injury or loss of life.

A. This appliance has a pilot which must

be lighted by hand. When lighting

the pilot, follow these instructions

exactly.

B. BEFORE LIGHTING smell all around

the appliance area for gas. Be sure to

smell next to the oor because some

gas is heavier than air and will settle

on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier,

call the re department.

C. Use only your hand to push in or turn the

gas control knob. Never use tools. If the

knob will not push in or turn by hand, don’t

try to repair it, call a qualied service tech-

nician or gas supplier. Force or attempted

repair may result in a re or explosion.

Do not use this appliance if any part has

been under water. Immediately call a

qualied service technician to inspect

the appliance and to replace any part of

the control system and any gas control

which has been under water.

LIGHTING

INSTRUCTIONS

1. STOP! Read the safety information

above.

2. Make sure equipment shutoff valve is

fully open.

3. Turn off any electric power to the appli-

ance if service is to be performed.

4. Turn control knob clockwise to the

OFF position.

5. Wait ve (5) minutes to clear out any gas.

Then smell for gas, including near the

oor. If you smell gas, STOP! Follow “B”

Control

Knob

Control

Knob

www.fmiproducts.com

125311-01A 15

10. To shut off burners only and leave pilot

lit, turn control knob clockwise to

the PILOT position.

WARNING: Always operate

manual control heaters at the

locked positions. Operation

between these positions may

create a possible health hazard

if used in a poorly ventilated

room. Read owner’s manual for

complete instructions.

CAUTION: Do not try to ad-

just heating levels by using the

equipment shutoff valve.

Figure 21 - Pilot

OPERATION

Continued

Thermocouple Ignitor Electrode

Pilot Burner

LOW

OFF

Control 16,000 & 26,000 &

Knob 18,000 Btu/Hr

30,000 Btu/Hr

LOW

HIHI

OFF

MEDMED

Control 16,000 & 26,000 &

Knob 18,000 Btu/Hr 30,000 Btu/Hr

OFFOFF

ONON

THERMOSTAT MODELS

Turn thermostat control knob counterclock-

wise to the desired heating level. The main

burner should light. Set control knob to any

heat level between 1 and 5 (see Figure 23).

Figure 22 - Burner Patterns for Manual

Control Models

Figure 23 - Burner Patterns

TO TURN OFF GAS

TO APPLIANCE

1. Turn control knob clockwise to the

OFF position.

2. Turn off all electric power to the appliance

if service is to be performed.

3. Close equipment shutoff valve (see Figure

16, page 13).

TO SELECT

HEATING LEVEL

CAUTION: Do not try to ad-

just heating levels by using the

equipment shutoff valve.

MANUAL CONTROL MODELS

WARNING: When running

heater, set control knob at LOW,

MED or HI locked positions.

Never set control knob between

locked positions. Poor combus-

tion and higher levels of carbon

monoxide may result.

Slightly press in control knob and turn coun-

terclockwise to the LOW, MED or HI positions

(see Figure 22).

IMPORTANT: Release downward pressure

while turning control knob. Control knob will

lock at the desired position.

www.fmiproducts.com 125311-01A16

OPERATION

Continued

THERMOSTAT CONTROL

OPERATION

The thermostatic control used on these

models differs from standard thermostats.

Standard thermostats simply turn on and off

the burner. The thermostat used on this heater

senses the room temperature. At times the

room may exceed the set temperature. If so,

the burner will shut off. The burner will cycle

back on when room temperature drops below

the set temperature. The control knob can be

set to any comfort level between 1 and 5. All

plaques will turn off and on.

Note: The thermostat sensing bulb mea-

sures the temperature of air near the heater

cabinet. This may not always agree with

room temperature (depending on housing

construction, installation location, room size,

open air temperatures, etc.) Frequent use of

your heater will let you determine your own

comfort levels.

MANUAL LIGHTING

PROCEDURE

1. Remove front panel (see Figure 7, page 9).

2. Follow steps 1 through 5 under Lighting

Instructions, page 14.

3. With control knob pressed in, strike match.

Hold match to pilot until pilot lights.

4. Keep control knob pressed in for 30 sec-

onds after lighting pilot. After 30 seconds,

release control knob. Now follow step 9

under Lighting Instructions, page 14.

5. Replace front panel.

BLOWER

OPERATION

WARNING: Blower acces-

sory must be grounded. Blower

comes with a three-prong,

grounding plug as shown in

Figure 24. The plug is your

protection against electrical

shock. Plug it into a standard,

three-hole, grounded, outlet. If

cord needs replacing, use only a

cord with a three-prong, ground-

ing plug.

CAUTION: Label all wires

prior to disconnection when

servicing controls. Wiring errors

can cause improper and danger-

ous operation.

CAUTION: Do not plug power

cord into electrical outlet until

installation is complete.

Extension Cord

Use extension cord if needed. The cord must

have a three-prong, grounding plug and a

three-hole receptacle. Make sure cord is in

good shape. It must be heavy enough to carry

the current needed. An undersized cord will

cause a drop in line voltage. This will result in

loss of power and overheating. Use a No. 16

AWG cord for lengths less than 50 feet.

CAUTION: Verify proper op-

eration after servicing.

Operating Blower

The blower is connected to a thermostat.

When unit heats up, the blower will operate.

A few minutes after unit cycles off or is turned

off, blower will shut off. Blower will cycle on

and off in this manner. Note: If you have a

heater with a thermostat, the heater and

blower will not turn off and on at exactly the

same time. Blower cycle times will vary with

heat setting selected.

Grounded

Outlet

Figure 24 - Grounding Plug

Thermostat

Sensor

Switch

Green

White

Green

White

110/115

V.A.C. Blower

Motor

Black Black

Figure 25 - Wiring Diagram for Blower

Accessory

www.fmiproducts.com

125311-01A 17

WARNING: Failure to keep

the primary air opening(s) of

the burner(s) clean may result in

sooting and property damage.

ODS/PILOT AND BURNER

Use a vacuum cleaner, pressurized air or

small, soft bristled brush to clean.

BURNER PILOT AIR INLET

The primary air inlet holes allow the proper amount

of air to mix with the gas. This provides a clean

burning ame. Keep these holes clear of dust, dirt

and lint. Clean these air inlet holes prior to each

heating season. Blocked air holes will create soot.

We recommend that you clean the unit every

three months during operation and have heater

inspected yearly by a qualied service person.

Thermocouple Pilot Burner

Pilot Burner

Thermocouple

Blue Flame

Yellow Flame

INSPECTING HEATERS

Figure 26 - Correct Pilot Flame Pattern

Figure 27 - Incorrect Pilot Flame Pattern

BURNER FLAME PATTERN

Figure 28 shows a correct burner ame pat-

tern. Figure 29 shows an incorrect burner

ame pattern.

If burner ame pattern is incorrect, as shown

in Figure 29

• turn heater off (see To Turn Off Gas to Ap-

pliance, page 15)

• see Troubleshooting, page 18

CLEANING AND MAINTENANCE

Check pilot ame pattern and burner ame

patterns often.

PILOT FLAME PATTERN

Figure 26 shows a correct pilot ame pattern.

Figure 27 shows an incorrect pilot ame pat-

tern. The incorrect pilot ame is not touching the

thermocouple. This will cause the thermocouple

to cool. When the thermocouple cools, the

heater will shut down.

If pilot ame pattern is incorrect, as shown

in Figure 27

• turn heater off (see To Turn Off Gas to Ap-

pliance, page 15)

• see Troubleshooting, page 18

Note: The pilot ame on natural gas units will

have a slight curve, but ame should be blue

and have no yellow or orange color.

WARNING: Turn off heater

and let cool before cleaning.

CAUTION: You must keep

control areas, burner and circu-

lating air passageways of heater

clean. Inspect these areas of

heater before each use. Have

heater inspected yearly by a

qualied service person. Heater

may need more frequent clean-

ing due to excessive lint from

carpeting, bedding material, pet

hair, etc.

Figure 28 - Correct Burner Flame Pattern

Figure 29 - Incorrect Burner Flame

Pattern

www.fmiproducts.com 125311-01A18

We also recommend that you keep the burner

tube and pilot assembly clean and free of dust

and dirt. To clean these parts we recommend

using compressed air no greater than 30 PSI.

Your local computer store, hardware store or

home center may carry compressed air in a

can. If using compressed air in a can, please

follow the directions on the can. If you don’t

follow directions on the can, you could dam-

age the pilot assembly.

1. Shut off unit, including pilot. Allow unit to

cool for at least thirty minutes.

2. Inspect burner, pilot and primary air inlet

holes on orice holder for dust and dirt

(see Figure 30).

3. Blow air through the ports/slots and holes

in the burner.

4. Never inset objects into the pilot tube.

5. Blow air into the primary air holes on the

orice holder.

Clean pilot assembly also. A yellow tip on the

pilot ame indicates dust and dirt in the pilot

Figure 30 - Pilot Inlet Air Hole

CLEANING AND MAINTENANCE

Continued

Pilot

Assembly

Pilot Air

Inlet Hole

CABINET

Air Passageways

Use pressurized air to clean.

Exterior

Use a soft cloth dampened with a mild soap

and water mixture. Wipe the cabinet to re-

move dust.

SPECIFICATIONS

GWRN18TC, VSHRN18T

• Natural Gas Only

• 18,000 Btu/h

• Pressure Regulator Setting: 6" W.C.