Forest garden DAMSON PLAYHOUSE User manual

DAMSON PLAYHOUSE REQUIRED TOOLS: (NOT SUPPLIED)
POZI DRIVE SCREWDRIVER
DRILL
TAPE MEASURE
PH8 Parts list:
B
Issue 0414
MUST PRE DRILL
SPIRIT LEVEL
C
F
A
H
I
E
L
PH2PP
(Large Plain Panel) Qty1
PH2DPV2
(Door Panel) Qty 1
18386908
(Roof sheet) Qty 2
PW480250
(Window) Qty 4
28280100CRCTDTR
(Door Handle 100mm) Qty 1
SBB80120875PAII45DT
(Barge Board) Qty 4
28281758CRCT (Batten 1758mm) Qty 1
PH8
Instruction Reference
Fixing Pack (PH8FPV2)
FELT NAIL
Not to Scale
46
2
90
14
Hinge
25mm Screw
50mm Screw
25mm Screw (black)
1
20
30mm Screw
32
Magnetic
Catch and Plate
D
PH8FL
(Floor) Qty1
G
PH1PE
(Plain End) Qty 2
PH1DR
(Door) Qty 1
N
J
40121024PARDTR
(Corner Strip 1024mm) Qty 4
O
M
28281838CRCT (Batten 1832mm) Qty 2
32
Panel Pins
EN71 COMPLIANT
15120250PARDTR
(Glazing Strip) Qty 16
K
Important :
Assembly of this
product requires
a minimum of two
adults only.
Warning. Only for domestic use
Biocidal Product Regulation (EU 528/2012) Article 58 Information
This article contains timber treated with Celcure AC-500, incorporating biocidal products
to give protection against wood destroying insects & wood rotting fungi.
Contains: Basic copper carbonate (Copper (II) carbonate – Copper (II) hydroxide (1:1)),
Boric acid, Benzalkonium chloride.
Wear gloves when handling freshly treated wood. Avoid breathing dust when cutting
treated or untreated wood. Dispose of off-cuts responsibly – do not burn.
IMPORTANT, RETAIN FOR FUTURE REFERENCE; READ
CAREFULLY
- Most buildings are pre-treated with a factory base coat for protection
during storage and transit. We recommend that you treat your new
building as soon as possible after assembly using a wood preservative
treatment. Apply in accordance with the manufacturers instructions.
- Timber is a natural material. It will shrink and swell as a result of
varying moisture content.
- Please keep all plastic bags and small parts away from children
- This product must be built on a solid level base and at least two
metres away from any structure or obstruction.
Warnings
-This product is for outdoor use only.
-This product is intended for use by children of up to age 10 years.
-Only for domestic use
Technical Help line: 7777 089 8.30 am and 5.00 pm Monday to 0333
Friday.
In line with your statutory rights, please check all parts prior to
assembly, as assembly of damaged parts may be deemed to be
acceptance and this may affect the remedies you are entitled to. If the
product is not constructed in accordance with the instructions, or is
altered in anyway (e.g. painted), the manufacturer cannot be held liable
for any resulting damage
Slipping, Tripping
& Falling
40120530PAIIDT
(Strip 530mm ) Qty 4
40120586PAIIDT
(Strip 586mm ) Qty 4
85052
Felt Qty 1
BLACK SAND FELT
P
28280694CRCTA1
(Batten 694mm ) Qty 2

1
A
B
A
Top View
B
C
C
A
C
Make sure that the panels are sat on top
of the floor and are lined up correctly.
Fix each panel to the floor using 50mm
screws making sure they locate in to the
bearers underneath.
A
Forest Garden Ltd, Unit 288 Hartlebury Trading Estate, Hartlebury, Worcestershire, DY10 4JB
Place the plain end panels against the ends of the large
plain panel (making sure all sides are flush) and fix them
together using 3 x 50mm screws for each end. Fit the
door panel inside the two ends and repeat the process.
A
M
Place the 1758mm batten so that it bridges
the two end panels at the apex as
illustrated. Fix this in place using a 50mm
screw at each end screwing at an angle.
Place a corner strip to each corner making
sure that it is flush. Secure each strip in
place using 3 x 25mm screws.
2
3
screw location
J
J
J

6
Place the magnetic catch against the
inside of the door frame but opposite the
magnetic plate on the reverse of the door.
Fix this in place using 2 x 25mm screws.
E
H
Place the hinges against the door
so that they are in line with the
battens on the reverse and secure
using 3 x 25mm (black) screws.
Place the door into the door
frame and fix the other end
of the hinge using 4 x 25mm
(black) screws for each.
Issue 0414
5
6
4
Place the handle against the door, in line with the edge
of the board and positioned just below the level of the
window. On the back of the door (inside) place the
magnetic plate opposite the handle and use 2 x 25mm
screws to fix both the plate and handle to the door
screwing from inside.
K
Insert a piece of the
glazing in to the frame
and fix it in place,
pinning a glazing strip
on each side as shown.
Use 2 x panel pins for
each strip.
G
K
Attention :
When positioning the door the gap between the door and the frame on the hinged side
must be no less than 12mm. The gap on the opening side must be less than 5mm.
Forest Garden Ltd, Unit 288 Hartlebury Trading Estate, Hartlebury, Worcestershire, DY10 4JB

6
F
L
Place roof sheet on top
of a 1838mm batten
again making sure that
all the edges are flush.
Secure the roof sheet
to the batten using 5 x
25mm screws.
Place each roof
section on to the
building so that they
are in line with the
apex. Fix the roof
sections in place using
3 x 25mm screws for
each end, screwing in
to the apex pieces.
Further secure the roof
using 2 x 30mm
screws going through
the roof into the panels
in line with the vertical
framing battens.
Place two 694mm
angled battens against
each end of the building
so that they are in line
with the top of the roof
and meet at the apex.
Fix each in place using
2 x 50mm screws.
Maintenance: -After assembling the building we recommend that you treat this using a wood preservative treatment. Repeat annually.
- Make sure that there are no sharp edges or screw heads protruding.
Regularly check - All fixing are tight.
- All parts for evidence of deterioration and replace in accordance with
the manufacturers instructions
8
7
Place the 586mm and 530mm
strips around the outside of the
window so that they are flush
and square. Secure each strip
with 2 x 30mm screws.
When securing the bottom
strip, take care to position the
screws towards the bottom the
strip to make sure you screw
through the thicker material
behind.
Place each of the barge boards against the ends of the building so that they are in line
with the pitch of the roof and meet at the apex. Place the shaped barge boards at the
front and the straight boards on the back.Fix each in place using 2 x 25mm screws.
Trim off any excess roof felt that may protrude underneath the boards.
Attention:
Take care when
trimming the
roof felt.
Unroll both lengths of felt and position each sheet centrally and so they
overlap each other at the apex. Each sheet should have an equal overhang
one each end and approximately a 40mm overhang on the eaves.
Secure the felt with the felt nails provided spaced at 150mm intervals.
Eaves
Apex
30mm screws
P
I
N
O