Forest lighting FL-ALC-90WXXK-YYZZ Service manual

INSTALLATION INSTRUCTION MANUAL
LED AREA LIGHT, 100-277VAC&277-480V
Rev A Aug 2016
SERIES:
FL-ALC-90WXXK-YYZZ;FL-ALC-120WXXK-YYZZ;FL-ALC-150WXXK-YYZZ ;
FL-ALC-150WHXXK-YYZZ;FL-ALC-220WXXK-YYZZ;FL-ALC-220WHXXK-YYZZ;
FL-ALC-300WXXK-YYZZ;FL-ALC-300WHXXK-YYZZ;
Model number parameter list:
1. Introduction
This LED Flood light uses the latest in solid state lighting technology for long life, low
maintenance, and high efficiency.
The same as traditional HID lighting. There are two installation methods, suitable for various
occasion.
An internal power-factor-corrected switch-mode supply allows it to be used from
any nominal 100-277V, 60Hz AC supply without any variation in light output.
Suitable for use in the following conditions:
• Ambient Temp: -20~+40°C
• Wet Locations
Note: Save these instructions for future reference.
2. Installation
Item
Model
Input Voltage
Power
Factor
Watt
Input Current
A
FL-ALC-90WXXK-YYZZ
100-277VAC
≥0.9
90W
1.5A
C
FL-ALC-120WXXK-YYZZ
100-277VAC
120W
1.5A
D
FL-ALC-150WXXK-YYZZ
100-277VAC
150W
1.87A
E
FL-ALC-150WHXXK-YYZZ
277-480VAC
150W
0.64A
F
FL-ALC-220WXXK-YYZZ
100-277VAC
220W
2.85A
G
FL-ALC-220WHXXK-YYZZ
277-480VAC
220W
1.0A
H
FL-ALC-300WXXK-YYZZ
100-277VAC
300W
4.0A
I
FL-ALC-300WHXXK-YYZZ
277-480VAC
300W
1.5A
Warning:
To avoid the risk of fire, explosion, or electric shock, this product should be installed,
inspected, and maintained by a qualified electrician only, in accordance with all applicable
electrical codes.
800.994.2143
www.forestlighting.com
Forest Lighting, 2252 Northwest Pkwy SE, Suite D, Marietta, GA 3006.

For supply connections use wire rated for at least 90°C
Installation Steps:
Refer to the following mounting hole diagram when installing the fixture.
1. Wall Mounting
1.Use expansion bolts to secure the fixture on mounting surface.
2.Keep enough wire length to ensure adjusting angle unhindered.
Connect wires into wiring terminal; white wire to “Neutral”
terminal, black wire to “Live” terminal, green wire to
“Ground” terminal. Fix wires using screws.
2.Mounting with a Slipfitter for Models:
FL-ALC-90WXXK-YYZZ;FL-ALC-120WXXK-YYZZ;FL-ALC-150WXXK-YYZZ ;
FL-ALC-150WHXXK-YYZZ;FL-ALC-220WXXK-YYZZ;FL-ALC-220WHXXK-YYZZ;
FL-ALC-300WXXK-YYZZ;FL-ALC-300WHXXK-YYZZ;
Warning:
To avoid electric shock:
•Be certain electrical power is OFF before and during installation and maintenance.
•Luminaire must be connected to a wiring system with an equipment-grounding conductor.
Warning:
To avoid explosion:
•Make sure the supply voltage is the same as the rated luminaire voltage.
•Do not install where the marked operating temperatures exceed the ignition temperature of
the hazardous atmosphere.
•Do not operate in ambient temperatures above those indicated on the luminaire nameplate.
•Keep lens tightly closed when in operation.
FL-ALC-90WXXK-YYZZ
FL-ALC-120WXXK-YYZZ
FL-ALC-150WXXK-YYZZ
FL-ALC-150WHXXK-YYZZ
FL-ALC-220WXXK-YYZZ
FL-ALC-220WHXXK-YYZZ
FL-ALC-300WXXK-YYZZ
FL-ALC-300WHXXK-YYZZ
800.994.2143
www.forestlighting.com
Forest Lighting, 2252 Northwest Pkwy SE, Suite D, Marietta, GA 3006.

Step 1
Adjust the fixture orientation and tighten the bolt. Above
photo for the rocker installation hole, for the sensor
installation hole at the top.
Step 2
Use a post of diameter 2.36” for mounting.
Tighten with screws. Side cover from the side
connection.
3.Mounting with a Trunnion for Models:
FL-ALC-90WXXK-YYZZ;FL-ALC-120WXXK-YYZZ;FL-ALC-150WXXK-YYZZ ;
FL-ALC-150WHXXK-YYZZ;FL-ALC-220WXXK-YYZZ;FL-ALC-220WHXXK-YYZZ;
FL-ALC-300WXXK-YYZZ;FL-ALC-300WHXXK-YYZZ;
Step 1
Drill holes on the square base pole according to the
mounting hole diagram above.
Step 2
Adjust the fixture orientation tighten the screws.
4.Mounting with Arm for Models:
FL-ALC-90WXXK-YYZZ;FL-ALC-120WXXK-YYZZ;FL-ALC-150WXXK-YYZZ ;
FL-ALC-150WHXXK-YYZZ;FL-ALC-220WXXK-YYZZ;FL-ALC-220WHXXK-YYZZ;
FL-ALC-300WXXK-YYZZ;FL-ALC-300WHXXK-YYZZ;
Directly attach screw to the lamp post. Side cover opens from the side connection
After installation, please
check that lighting fixture is firmly affixed.
check that wires are connected correctly.
Turn on power to ensure, lighting fixture connection works. For problems, please contact local
dealer.
800.994.2143
www.forestlighting.com
Forest Lighting, 2252 Northwest Pkwy SE, Suite D, Marietta, GA 3006.