Finelite HP-2 User manual

Note: All power connections to be installed to
local/national codes by a Certified Electrician.
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.com
1
© 2016 FI ELITE, I C. ALL RIGHTS RESERVED. Form 98240 V2. 11/16
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S
HP-2 Recessed T-Bar Mitered Corner Installation Instructions
Conduit Plate
(provided)
#8-18 x 1/4" Screws
(provided)
Conduit
(by others)
Jam Nut (by others)
Wiring Connections
Starter
Step 2
Install starter luminaire on to T-Bar.
T-Bar Bracket (provided)
Starter
#8-18 x 1/4"
Screws (4) (provided)
Tie-wire
(by others)
Step 3
Attach T-Bar bracket (provided) to luminaire with #8-18 x 1/4" screw (provided).
Secure luminaire to structure using tie-wire (by others), as per code.
Step 4
Remove conduit plate then install wiring through conduit plate and through jam nut. Secure jam nut onto
conduit. Make wiring connections and then reinstall conduit plate.
Diffuser
Starter
Step 1
Remove diffuser and set aside to prevent it from
getting dirty or damaged.
0 - 10V
Dimming
Scan QR code for
helpful video(s)
Wires
Splice Box Door
Jam Nut
Conduit
Wires
Splice box door
Open optional splice box door to access wiring. Run power cable through knock-out. Make electrical connections. Secure
conduit on to splice box with jam nut and close splice box door.
OPTIONAL SPLICE BO

Note: All power connections to be installed to
local/national codes by a Certified Electrician.
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.com
2
© 2016 FI ELITE, I C. ALL RIGHTS RESERVED. Form 98240 V2. 11/16
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S
HP-2 Recessed T-Bar Mitered Corner Installation Instructions
Back Plate
Joiner/Ender
Starter
Elbow Sleeves
Joiner/Ender
Starter
Channels
Step 7
Align elbow sleeves with channels in body. Slide joiner/ender onto starter.
Remove back plate clips (provided) from back plates at corner joint.
Starter
Joiner/Ender
Step 6
Slide joiner/ender luminaire onto T-Bar.
Starter
Joiner/Ender
Double Diffuser
(pre-installed)
Step 8 Step 9
Slowly swing down back plates. CAUTION: Do not twist back plate when swinging
down - it will come out of the support extrusion. ote that the screw shown is the
pivot point and the back plate can be slid a few inches either way for ease of
access to the driver space.
IMPORTANT STEP: Secure joint with two yoke brackets (provided) using #10-32 x
5/8" screws (provided). CAUTION: When installed correctly these brackets will pull
luminaires together to make a tight joint. Do not over-tighten.
#10-32 x 5/8"
Screws (provided)
Yoke Brackets
(provided)
Starter
Joiner/Ender
Step 10
Back Plate Clip
Pivot Point
Joiner/Ender
Diffuser
Step 5
Remove diffuser from joiner/ender luminaire and set aside to prevent it from getting
dirty or damaged.
IMPORTANT STEP

Note: All power connections to be installed to
local/national codes by a Certified Electrician.
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.com
3
© 2016 FI ELITE, I C. ALL RIGHTS RESERVED. Form 98240 V2. 11/16
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S
HP-2 Recessed T-Bar Mitered Corner Installation Instructions
Diffuser
Diffuser
Starter
T-Bar Bracket
Joiner/Ender
#8-18 x 1/4" Screws
(4) (provided)
#6-20 x 1/2" Self
Drilling Screws (4)
(provided)
Secure To Structure
(by others)
Step 12
Step 13
Attach T-Bar bracket (provided) onto joiner/ender with #8-18 x 1/4" screws (provided). Secure joiner/ender to structure using tie-wire
(by others), as per code. Secure all luminaires to the T-Bar by driving #6-20 x 1/2" self drilling screws (provided) through the T-Bar
brackets (provided) into the T-Bar.
Reinstall diffusers and turn power on to luminaires.
Plug-Together Wiring
Back Plate
Double Diffuser
(pre-installed)
Starter
Joiner/Ender
Connect plug-together wiring. Close all back plates by pushing them back in their original position and pushing the clips
back in.
Step 11
Back Plate Clip