Forging Mount FM4545 User manual

36”
MAX
26.4LBS
MONITOR DESK MOUNT
INSTALLATION MANUAL
Thanks for choosing our product! We strive to provide the best quality and services
for our customers. Would you kindly share your experience on Amazon if you are
satisfied? If you have any questions, please feel free contact us.
Email: [email protected]
We're ready to help!
Model：FM4545
MAX
75*75mm
100*100mm
1

IMPORTANT SAFETY INFORMATION
Read the entire instruction manual before you start installation and assembly.
If you have any questions regarding any of the instructions or warnings, please
contact US via: [email protected]
！BE CAREFUL
CAUTION: Exceeding the weight capacity can result in serious personal injury or damage to
equipment!
1. Mounts must be attached as specified in assembly instructions. Improper installation may result
in damage or serious personal injury.
2. Safety gear and proper tools must be used. This product should only be installed by professionals.
3. Make sure that the supporting surface will safely support the combined weight of the equipment
and all attached hardware and components.
4. Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
5. This product contains small items that could be a choking hazard if swallowed. Keep these items
away from children.
6. This product is intended for indoor use only. Using this product outdoors could lead to product
failure and personal injury.
IMPORTANT:
Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, can contact us via: [email protected].
MAINTENANCE:
Check that the bracket is secure and safe to use at regular intervals. (at least every three months)
WEIGHT RESTRICTIONS
DO NOT exceed the maximum weight indicated. This
mounting system is intended for use only with the
maximum weights indicated. Use with products
heavier than the maximum weights indicated may
result in failure of the mount and its accessories,
causing possible damage and or injury.
WARNING
2
4-26.4LBS
（2-12kg）
Holds up to

2（×1）1（×1）
4（×1） 6（×1） 7（×1）
9（×1） 10（×1）
8（×1）
PACKING LIST
3
3MM（×1） 4MM（×1）
M4×10（×4）
A
M5×10（×4）
B
M6×10（×2）
D
EF G
5MM（×1）
M8×20（×1）
C
5（×1）
3（×1）
Base Clip Plate Long Bolt
VESA Plate Cable Cover Anti-slip Pad
Clamp Bracket Lower Arm Upper Arm

4
Installation Method 1 Clamp Installation
1a-4
1a-3b
1a-21a-1
1a-3a
C
G
1
5
10
D
2 : 1
D
F
4
0.39"-1.97" (10-50mm)
4
D
2 : 1
F
D
1.18"-3.15" (30-80mm)

5
Installation Method 2 Grommet Base Installation
1b-1
1b-2
2
E
A
10
1
G
2
3

6
3
G
A/B
Connect with Monitor
Use a wrench (G) to screw the screws (A/B) into the four
holes at the back of the monitor to avoid damaging the
monitor by over tightening the screws.
4
H
1 : 1
H
1 : 1
A
1 : 1
A
1 : 1
A
When the display is inserted
into the quick release head,
make sure the knob is vertical.
After insertion, rotate the knob
90 degrees to the left.

7
5-2
5-1
G
+
Press the arm to make it keep it in horizontal position and then use the Allen
Key to adjust the screw on the arm.Turn counter-clockwise(”+ ” direction)
to increase gas spring tension till can hold the weight of your monitor.
Case 1：Monitor/Arm Fall Down (After Install Your Monitor)
Note: You may need to turn the screw by many circles to tighten the arm.
fall down
G
Case 2：Monitor/Arm Pops Up (After Install Your Monitor)
Press the arm to make it keep it in horizontal position and then use the Allen
Key to adjust the screw on the arm.Turn clockwise(”- ” direction) to reduce
gas spring tension till can stay the position needed.
Note: You may need to turn the screw by many circles to tighten the arm.
pop up
-

6
6
7
If the pitching angle too tight or too loose when
adjusting the mount, please adjust the screw
Adjust Flexiblity
Limit Screw
Turn clockwise to tighten
Turn counterclockwise to loose
+
-
G
8
This limit screw can prevent
the head from sinking. It can
also be disassembled if
necessary
Adjustment

9
8
+90°
-45°
180°
360°
360°
360°
Cable Management
Adjustable Instruction
9

10
Thank you again
for choosing this forgingmount product!