Fortinet FortiGate-5140-R User manual
FAN TRAY FAN TRAYFAN TRAY
1311975312468101214
5140
CRITICAL
RESET
MAJOR
MINOR
USER1
USER2
USER3
5140SAP
SERIAL 1 SERIAL 2 ALARM
FILTER
12
012
10/100
link/Act
ETH0
Service
RESET
STATUS
HotSwap
link/Act
ETH0 ETH1
10/100
5000SM
10/100
link/Act
ETH0
Service
RESET
STATUS
HotSwap
link/Act
ETH0 ETH1
10/100
5000SM
ADM-FB8
HS
OOS
PWR
OT
1234
LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT
5678
ADM-FB8
HS
OOS
PWR
OT
1234
LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT
5678
ADM-FB8
HS
OOS
PWR
OT
1234
LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT
5678
ADM-FB8
HS
OOS
PWR
OT
1234
LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT
5678
ADM-FB8
HS
OOS
PWR
OT
1234
LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT
5678
ADM-FB8
HS
OOS
PWR
OT
1234
LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT LINKACT
5678
ADM-XB2
LINK
ACT
12
HS
OOS
PWR
OT
LINK
ACT
ADM-XB2
LINK
ACT
12
HS
OOS
PWR
OT
LINK
ACT
ADM-XB2
LINK
ACT
12
HS
OOS
PWR
OT
LINK
ACT
ADM-XB2
LINK
ACT
12
HS
OOS
PWR
OT
LINK
ACT
FortiGate-5140-R Power and cooling enhancements to
support the FortiSwitch-5203B
01-400-175441-20120709
This technical note describes how to change the configuration of the FortiGate-5140-R chassis to support operating
FortiSwitch-5203B boards in chassis slots 1 and 2.
The most recent versions of all FortiGate-5000 series documents are available from the FortiGate-5000 page of the
Fortinet Technical Documentation web site (http://docs.fortinet.com).
Visit http://support.fortinet.com to register your Fortinet product. By registering you can receive product updates,
technical support, and FortiGuard services.
FortiGate-5140-R
Power and cooling enhancements
to support the FortiSwitch-5203B
Technical Note
FortiGate-5140-R Power and cooling enhancements to support the FortiSwitch-5203B
01-400-175441-20120709
http://docs.fortinet.com/
Warnings and cautions
Only trained and qualified personnel should be allowed to install or maintain
FortiGate-5000 series equipment. Read and comply with all warnings, cautions and
notices in this document.
• Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used
Batteries According to the Instructions.
• Turning off all power switches may not turn off all power to the FortiGate-5000 series
equipment. Some circuitry in the FortiGate-5000 series equipment may continue to
operate even though all power switches are off.
• FortiGate-5000 equipment must be protected by a readily accessible disconnect
device or circuit breaker that can be used for product power down emergencies.
• Many FortiGate-5000 components are hot swappable and can be installed or
removed while the power is on. But some of the procedures in this document may
require power to be turned off and completely disconnected. Follow all instructions in
the procedures in this document that describe disconnecting FortiGate-5000 series
equipment from power sources, telecommunications links and networks before
installing, or removing FortiGate-5000 series components, or performing other
maintenance tasks. Failure to follow the instructions in this document can result in
personal injury or equipment damage.
• Install FortiGate-5000 series chassis at the lower positions of a rack to avoid making
the rack top-heavy and unstable.
• Do not insert metal objects or tools into open chassis slots.
• Electrostatic discharge (ESD) can damage FortiGate-5000 series equipment. Only
perform the procedures described in this document from an ESD workstation. If no
such station is available, you can provide some ESD protection by wearing an
anti-static wrist strap and attaching it to an available ESD connector such as the ESD
sockets provided on FortiGate-5000 series chassis.
• Make sure all FortiGate-5000 series components have reliable grounding. Fortinet
recommends direct connections to the building ground.
• If you install a FortiGate-5000 series component in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be greater
than room ambient. Make sure the operating ambient temperature does not exceed
Fortinet’s maximum rated ambient temperature.
• Installing FortiGate-5000 series equipment in a rack should be such that the amount
of airflow required for safe operation of the equipment is not compromised.
• FortiGate-5000 series chassis should be installed by a qualified electrician.
• FortiGate-5000 series equipment shall be installed and connected to an electrical
supply source in accordance with the applicable codes and regulations for the
location in which it is installed. Particular attention shall be paid to use of correct wire
type and size to comply with the applicable codes and regulations for the installation /
location. Connection of the supply wiring to the terminal block on the equipment may
be accomplished using Listed wire compression lugs, for example, Pressure Terminal
Connector made by Ideal Industries Inc. or equivalent which is suitable for AWG-10.
Particular attention shall be given to use of the appropriate compression tool specified
by the compression lug manufacturer, if one is specified.
• This product is only intended for use in a Restricted Access Location.
FortiGate-5140-R Power and cooling enhancements to support the FortiSwitch-5203B
01-400-175441-20120709 3
http://docs.fortinet.com/
FortiGate-5140-R
This document describes how to change the configuration of the FortiGate-5140-R
chassis to support FortiSwitch-5203B. board. By default, the FortiGate-5140-R does not
provide adequate cooling or power for the FortiSwitch-5203B board. This technical note
describes how to:
• Increase cooling by setting the minimum fan level to 8
• Increase the power capacity for chassis slots 1 and 2 to 220 watts
To increase cooling capacity and power capacity
To complete this procedure, you need:
• An electrostatic discharge (ESD) preventive wrist strap with connection cord
1Attach the ESD wrist strap to your wrist and to an available ESD socket or wrist strap
terminal.
2Connect to the FortiGate-5140-R shelf manager CLI.
You can connect to the shelf manager CLI by connecting the console cable supplied
with your chassis to a management PC console port and to the appropriate shelf
alarm panel serial port. To connect to the primary shelf manager use Serial 1. To
connect to the secondary shelf manager use Serial 2.
Figure 1: Connecting to a shelf manager serial port
3Connect the console cable supplied with your chassis to your PC or other device
RS-232 console port.
4Start a terminal emulation program (for example, HyperTerminal) on the management
computer. Use these settings:
FortiGate-5000 series boards and chassis must be protected from static discharge and
physical shock. Only handle or work with FortiGate-5000 equipment at a static-free
workstation. Always wear a grounded electrostatic discharge (ESD) preventive wrist
strap when handling FortiGate-5000 equipment.
CRITICAL
RESET
MAJOR
MINOR
USER1
USER2
USER3
5140SAP
SERIAL 1 SERIAL 2 ALARM
SERIAL 2 (Secondary
Shelf Manager)
SERIAL1 (Primary
Shelf Manager) FortiGate-5140 Shelf Alarm Panel
Fortinet
RJ-45 to
9-pin
Console
Cable
To PC
RS-232
Console
Port
FortiGate-5140-R Power and cooling enhancements to support the FortiSwitch-5203B
401-400-175441-20120709
http://docs.fortinet.com/
5Press enter to connect to the CLI.
6At the login prompt enter the shelf manager user name and password.
7Use the following command to start the vi editor and edit the shelf manager
configuration file and change mini-fan level to 8.
# vi /etc/shelfman.conf.ACB-IV
The contents of the shelfman.conf file are displayed. Note that the MIN_FAN_LEVEL
is 3:
FAN_LEVEL_STEP_DOWN = 1
NORMAL_STABLE_TIME = 1800
IPMB_LINK_ISOLATION_TIMEOUT = 60
INITIAL_FAN_LEVEL = 8
MIN_FAN_LEVEL = 3
REDUNDANCY_NET_ADAPTER = "usb0"
8Enter Ito edit, move cursor and change MIN_FAN_LEVEL=3 to MIN_FAN_LEVEL=8.
9Press Esc.
10 Enter :w to save.
11 Enter :q to quit.
12 Enter the following commands to change the power setting of slot1 and slot2
clia shelf pwrcapability 41 0xfe 220
clia shelf pwrcapability 42 0xfe 220
13 Power cycle the chassis to make sure the changes take effect.
Verifying the changes
1When the chassis has started back up enter the following command to check the
minimum fan level:
# clia minfanlevel
Pigeon Point Shelf Manager Command Line Interpreter
Minimal Fan Level is 8
Dynamic Minimum Fan Level is 8
Baud Rate (bps) 9600
Data bits 8
Parity None
Stop bits 1
Flow Control None
FortiGate-5140-R Power and cooling enhancements to support the FortiSwitch-5203B
01-400-175441-20120709 5
http://docs.fortinet.com/
2Enter the following command to check the power setting for each chassis slot:
# clia shelf -v pm
The following command output shows slots 1 and 2 supplying 220 Watts of power
and all other slots supplying 200 Watts.
Pigeon Point Shelf Manager Command Line Interpreter
PICMG Shelf Activation And Power Management Record (ID=0x12)
Version = 1
Allowance for FRU Activation Readiness: 20 seconds
FRU Activation and Power Description Count: 17
Hw Address: 41 (82), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 220 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
Currently Assigned Power: 150.0 Watts
Hw Address: 42 (84), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 220 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
Currently Assigned Power: 150.0 Watts
Hw Address: 43 (86), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 200 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
Currently Assigned Power: 0.0 Watts
Hw Address: 44 (88), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 200 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
Currently Assigned Power: 0.0 Watts
Hw Address: 45 (8a), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 200 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
Currently Assigned Power: 0.0 Watts
Hw Address: 46 (8c), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 200 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
Currently Assigned Power: 0.0 Watts
FortiGate-5140-R Power and cooling enhancements to support the FortiSwitch-5203B
601-400-175441-20120709
http://docs.fortinet.com/
Hw Address: 47 (8e), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 200 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
Currently Assigned Power: 0.0 Watts
Hw Address: 48 (90), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 200 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
Currently Assigned Power: 0.0 Watts
Hw Address: 49 (92), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 200 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
Currently Assigned Power: 0.0 Watts
Hw Address: 4a (94), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 200 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
Currently Assigned Power: 0.0 Watts
Hw Address: 4b (96), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 200 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
Currently Assigned Power: 0.0 Watts
Hw Address: 4c (98), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 200 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
Currently Assigned Power: 0.0 Watts
Hw Address: 4d (9a), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 200 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
Currently Assigned Power: 0.0 Watts
Hw Address: 4e (9c), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 200 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
FortiGate-5140-R Power and cooling enhancements to support the FortiSwitch-5203B
01-400-175441-20120709 7
http://docs.fortinet.com/
Currently Assigned Power: 0.0 Watts
Hw Address: 08 (10), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 24 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
Currently Assigned Power: 20.0 Watts
Hw Address: 09 (12), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 24 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
Currently Assigned Power: 0.0 Watts
Hw Address: 10 (20), FRU ID: 0xfe, Maximum FRU Power
Capabilities: 400 Watts
Shelf Manager Controlled Activation: Enabled
Shelf Manager Controlled Deactivation: Enabled
Delay Before Next Power On: 0.0 seconds
Currently Assigned Power: 357.0 Watts
FortiGate-5140-R Power and cooling enhancements to support the FortiSwitch-5203B
01-400-175441-20120709 9
http://docs.fortinet.com/
FortiGate-5140-R
For more information
Training Services
Fortinet Training Services offers courses that orient you quickly to your new equipment,
and certifications to verify your knowledge level. Fortinet training programs serve the
needs of Fortinet customers and partners world-wide.
Visit Fortinet Training Services at http://campus.training.fortinet.com, or email
Technical Documentation
Visit the Fortinet Technical Documentation web site, http://docs.fortinet.com, for the
most up-to-date technical documentation.
The Fortinet Knowledge Base provides troubleshooting, how-to articles, examples,
FAQs, technical notes, and more. Visit the Fortinet Knowledge Base at
http://kb.fortinet.com.
Comments on Fortinet technical documentation
Send information about any errors or omissions in this or any Fortinet technical
Customer service and support
Fortinet is committed to your complete satisfaction. Through our regional Technical
Assistance Centers and partners worldwide, Fortinet provides remedial support during
the operation phase of your Fortinet product's development life cycle. Our Certified
Support Partners provide first level technical assistance to Fortinet customers, while the
regional TACs solve complex technical issues that our partners are unable to resolve.
Visit Customer Service and Support at http://support.fortinet.com.
Fortinet products End User License Agreement
See the Fortinet products End User License Agreement.
Fortinet products End User License Agreement For more information
FortiGate-5140-R Power and cooling enhancements to support the FortiSwitch-5203B
10 01-400-175441-20120709
http://docs.fortinet.com/
July 12, 2012
01-400-175441-20120709
Copyright© 2012 Fortinet, Inc. All rights reserved. Fortinet®, FortiGate®, and
FortiGuard®, are registered trademarks of Fortinet, Inc., and other Fortinet names herein
may also be trademarks of Fortinet. All other product or company names may be
trademarks of their respective owners. Performance metrics contained herein were
attained in internal lab tests under ideal conditions, and performance may vary. Network
variables, different network environments and other conditions may affect performance
results. Nothing herein represents any binding commitment by Fortinet, and Fortinet
disclaims all warranties, whether express or implied, except to the extent Fortinet enters
a binding written contract, signed by Fortinet’s General Counsel, with a purchaser that
expressly warrants that the identified product will perform according to the performance
metrics herein. For absolute clarity, any such warranty will be limited to performance in
the same ideal conditions as in Fortinet’s internal lab tests. Fortinet disclaims in full any
guarantees. Fortinet reserves the right to change, modify, transfer, or otherwise revise this
publication without notice, and the most current version of the publication shall be
applicable.
Visit these links for more information and documentation for your Fortinet products:
Fortinet Knowledge Base - http://kb.fortinet.com
Technical Documentation - http://docs.fortinet.com
Training Services - http://campus.training.fortinet.com
Customer Service and Support - http://support.fortinet.com
You can report errors or omissions in this or any Fortinet technical document to
Table of contents
