FourStar 11226112 User manual

BEFORE YOU BEGIN, PLEASE READ THE ASSEMBLY INSTRUCTIONS CAREFULLY.
FOLLOW THEM STEP BY STEP.
CAUTION:
1. ADULT SUPERVISION IS REQUIRED DUE TO SMALL PARTS. HANDLE WITH CARE
WHEN UNPACKING AND ASSEMBLING THE PRODUCT.
2. ASSEMBLE ON A SOFT SURFACES TO PREVENT DAMAGE TO THE PRODUCT FINISH.
3. MAKE SURE ALL PARTS ARE INCLUDED BEFORE ASSEMBLY.
ASSEMBLY TOOLS REQUIRED
Do you have any questions? Missing small parts or hardware? If you need assistance with the
assembly of your 4 CUBE ORGANIZER WITH 2 BINS please e-mail our Customer Service
Department at:
[email protected] or call us at [phone], (800)
639-3803
or visit www.fourstari.com
Please include the following information when contacting us:
•Where item was purchased
•Item, model, style or SKU number listed on instructions or box
•Part number, description of the part and quantity needed
This information will help us get the proper part to you faster.
MODEL: 11226112
4 CUBE
ORGANIZER
ASSEMBLY INSTRUCTIONS
PARTS LIST AND HARDWARE
NO HARDWARE LIST QTY
12 PCS
4 PCS
2 PCS
4 PCS
22 PCS
12 PCS
NO PARTS LIST QTY
SCREW
SHORT DOWEL
LONG DOWEL
NAIL LEG
POWER PIN
STICKER
A
B
C
D
E
1
2
3
4
5
6
2 PC
2 PC
1 PC
2 PC
1 PCS
SIDE PANEL
TOP & BOTTOM
PANEL
CENTER PANEL
CENTER SIDE
PANEL
BACK PANEL
SCREWDRIVER HAMMER
2
4
D
D
A
A
UNFINISHED
EDGE
FINISHED
EDGE
FINISHED
EDGE
FINISHED
EDGE
1
3
BD
A
A
C
FINISHED EDGE
UNFINISHED SURFACE
1
D
B
A
A
C
B
DFINISHED
EDGE
1
A
C
B
D
D
A
B
5
B
A
E
UNFINISHED
SURFACE
STEP 1.
1.1 INSTALL DOWEL (2) INTO PANEL PRE-DRILLED HOLES ON PANEL (D).
1.2 ATTACH NAIL LEG (4) INTO PANEL (A) USING HAMMER AS SHOWN.
STEP 2
2.1 ATTACH PANEL (B)(D)(C) USING SHORT DOWEL (2) AND LONG DOWEL (3), AS SHOWN.
2.2 ATTACH PANEL (A) TO ASSEMBLED UNIT WITH SCREW (1) USING SCREWDRIVER.
STEP 3
3.1 ATTACH PANEL (D) TO ASSEMBLED UNIT AS SHOWN.
3.2 FOLLOWED BY PANEL (B).
STEP 4.
4.1 INSERT SCREW (1) INTO PRE-DRILLED HOLES ON PANEL (B)
TIGHTEN USING SCREWDRIVER, AS SHOWN.
STEP 5.
5.1 ATTACH PANEL (E) TO ASSEMBLED UNIT.
5.2 TIGHTEN IT WITH POWER PIN (5) USING HAMMER, AS SHOWN.
STEP 6.
6.1 COVER THE SCREW WITH STICKER (6).
6.3 COMPLETE.
A
A
B
B
C
D
D
A
A
B
B
C
D
D
6

ANTES DE EMPEZAR, POR FAVOR LEER LAS INSTRUCCIONES DE ARMADO. SEGUIRLAS
PASO A PASO.
PRECAUCIÓN:
1. SUPERVISIÓN ADULTA SE REQUIERE POR PIEZAS PEQUEÑAS. TENGA CUIDADO AL
DESEMBALAJE Y MONTAJE DEL PRODUCTO.
2. ASSEMLE EN UNA SUPERFICIE SUAVE PARA EVITAR DAÑAR EL ACABADO DEL
PRODUCTO.
3. ASEGÚRESE DE QUE ESTÉN TODAS LAS PIEZAS ANTES DEL MONTAJE.
HERRAMIENTAS PARA EL MONTAJET
Do you have any questions? Missing small parts or hardware? If you need assistance with the
assembly of your 4 CUBE ORGANIZER WITH 2 BINS please e-mail our Customer Service
Department at:
[email protected] or call us at [phone], (800)
639-3803
or visit www.fourstari.com
Please include the following information when contacting us:
•Where item was purchased
•Item, model, style or SKU number listed on instructions or box
•Part number, description of the part and quantity needed
This information will help us get the proper part to you faster.
MODELO: 11226112
ORGANIZADOR EN
FORMA DE CUBO
ASSEMBLY INSTRUCTIONS
LISTA DE PIEZAS Y ACCESORIOS
NO HARDWARE LIST QTY
12 PCS
4 PCS
2 PCS
4 PCS
22 PCS
12 PCS
NO PARTS LIST QTY
TORNILLO
CLAVIJA CORTA
CLAVIJA LARGA
CLAVO CON PATA
CLAVO
ETIQUETA
A
B
C
D
E
1
2
3
4
5
6
2 PC
2 PC
1 PC
2 PC
1 PCS
PANEL LATERAL
PANEL SUPERIOR
E INFERIOR
PANEL CENTRAL
PANEL LATERAL
CENTRAL
PANEL POSTERIOR
DESTORNILLADOR MARTILLO
2
4
D
D
A
A
BORDE
SINTERMINAR
BORDE
ACABADO
BORDE
ACABADO
BORDE
ACABADO
PASO 1.
1.1 INSTALAR CLAVIJAS (2) EN LOS AGUJEROS PERFORADOS DEL PANEL (D).
1.2 ADJUNTE LA PATA CON CLAVO (4) EN EL PANEL (A) CON UN MARTILLO
COMO SE MUESTRA.
PASO 4.
4.1 INSERTE EL TORNILLO ( 1 ) EN LOS AGUJEROS PREVIAMENTE
PERFORADOS EN EL PANEL (B ) USANDO EL DESTORNILLADOR , COMO
SE MUESTRA .
PASO 5.
5.1 FIJE EL PANEL (E ) A LA UNIDAD ARMADA.
5.2 AJUSTE CON CLAVOS ( 5 ) CON UN MARTILLO , COMO SE MUESTRA.
PASO 6.
6.1 CUBRIR LOS TORNILLOS CON ETIQUETAS ( 6 ) .
6.3 COMPLETAR.
PASO 2
2.1 FIJE EL PANEL (B), (C) (D) Y (E) A LA UNIDAD ARMADA CON TORNILLO (1), COMO SE
MUESTRA.
2.2 FIJE EL PANEL (A) A LA UNIDAD ARMADA CON TORNILLO (1) USANDO
DESTORNILLADOR.
PASO 3
3.1 FIJE EL PANEL ( D ) A LA UNIDAD MONTADA COMO SE MUESTRA .
3.2 SEGUIDO DE PANEL ( B ) .
1
3
BD
A
A
C
BORDE ACABADO
SUPERFICIE SIN TERMINAR
1
D
B
A
A
C
B
DBORDE
ACABADO
1
A
C
B
D
D
A
B
5
B
A
E
SUPERFICIE SIN
TERMINAR
A
A
B
B
C
D
D
6
A
A
B
B
C
D
D