FOXEER LEGEND3 User manual

01/ Basic 3
02/ Basic Operations
4
14
04/ Connecting to the FOXEER App
15
05/ Customer Support
15
06/ Trademarks
03/ Setting Camera
6
Table of Contents
USER MANUAL
FOXEER TECHNOLOGY CO.,LTD
[email protected] www.foxeer.com

5. Programming Board Connector
6. Micro HDMI
7. Mini USB
8. 5V Power in
1. Main Board
2. Lens Module
3. Programming Board
4. WiFi Antenna
3 4
Basic
01 Basic Operations 02
In video mode, click the SHUTTER/WIFI button, the camera will
start recording, the buzzer will beep once, and the blue and red
LED lights will flash, click the SHUTTER/WIFI button again, the
camera will stop recording, the buzzer will beep three times,
and the blue and red LED lights will turn on.
In photo mode, click the SHUTTER/WIFI button, the camera will
take a picture, the buzzer will sound once, and the green and
red LED lights will be on.
Video and Photo
After the camera is turned on, click the POWER button on the
programming board to switch between video mode and photo
mode. The blue LED is on in video mode, and the green LED is
on in photo mode.
Mode Switch
After connecting with 5V power, click the POWER button on the
programming board, the buzzer will beep three times after the
camera is turned on. The blue and red LED lights are always on.
The camera is in standby mode at this time.
Power On

5 6
Basic Operations
02
When the camera is in standby mode, long press the
SHUTTER/WIFI button, the buzzer will beep for a long time, and
the WIFI will be on. The camera WIFI can be searched through
the mobile phone, the WiFi name is FOXEER_LEGEND3_XXXXXX.
(XXXXXX is the last six digits of the camera's mac address)
Open WiFi
Setting Camera
03
Video mode contains two capture modes: Video, Time Lapse Video.
Time Lapse Video is available only in 30fps except SuperVision, and
is captured without audio.
Video Mode
Photo mode contains four capture modes: Single, Timing, Auto
and Burst.
Photo Mode
To set camera, please set in FOXEER APP:
Resolution

7 8
Camera captures video automatically after powering on when
QUIKCAP on.
Quick Capture
With EIS, camera will with more stable view, and higher video
quality, only applies for 1080p60fps and 1080p30fps.
EIS
With Motion Detection ON, camera will start recording when
there is any object move on a scale captured by lens.
Motion Detection
Photo Size
Setting Camera
03 Setting Camera 03

9 10
Long Exposure applies only to single photo and determines the
amount of time that the shutter is open.The options for this
setting are 1/30, 1, 2, 5, 10, 30, 60 seconds.
Long Exposure
Available intervals for Self timer are 2, 3, 5, 10, 30, 60 seconds.
Timing Photo
Available intervals are 3, 5 or 10 photos every seconds.
Photo Burst
Available intervals are 3, 5, 10, 30 and 60 seconds.
Auto Photo
After removing power supply, camera will shut off on setting
time. Available intervals are 5, 10, 20, 30, 60 seconds.
Delay Off
Video format setting is mainly for watching the video on
TV/HDTV, to control the record frame rate of recording and
playback.
TV System
Light Frequency can be configured to Auto, 50Hz, 60Hz. If flash
on screen, please adjust the light frequency.
Light Frequency
The OSD(on-screen display) setting determine whether or not to
display camera recording icon and Parameter info. The options
for this setting are On(default) and Off.
OSD
Time Lapse Video available shooting interval is from 1 sec to 10
sec.
Time Lapse Video
Available intervals for Looping are 2, 3, 5 minutes. If you open the
Loop Recording, the recorded file will be split into multiple
sections written to the memory card, the camera keeps recording
until memory card is full, and then overwrite the previous
recorded small section content.
Looping Video
Setting Camera
03 Setting Camera 03
For best results when using the Long Exposure, mount
your camera on a tripod or other stable surface to
reduce the amount of blur in your video or photos.
PRO
TIP

11 12
Your camera can be configured to automatically power off after
a specific period(3, 5, 10 minutes) in which no videos or photos
are captured and no buttons are pressed, you can also configure
the camera to off this function.
Auto Off
Exposure Value Compensation affects the brightness of your
videos or photos. Adjusting this setting can improve image
quality when shooting in environments with contrasting lighting
conditions. Available setting range is -2.0~+2.0, the higher the
value, the lighter of the image.
EV COMP
The BOX has seven scenes-Normal(default), Flash, Night, Sports,
Landscape, Portrait and Sunset, you can select the appropriate
mode in different scenarios.
Scene
The BOX has seven effects filter-Normal(default), Art, Brown,
Negative film, Black and white, Vivid, 70 age Film, you can set
different effects for your videos and photos to make your work
different.
Effect
You can turn on or turn off the beeps.
Beeps
Your camera can be configured to start alarm for 3, 5, 10 minutes
after recording, beeps last until you press any button.
Video Timing Alarm
You can set mic volume to 100%, 90%, 80%, 70%, 60%, 50%, Off.
Mic Volume
Sharpness controls the sharpness of your video footage or
photos.
Sharpness
White balance lets you adjust the color temperature of videos
and photos to optimize for cool or warm lighting conditions.
White Balance
Setting Camera
03 Setting Camera 03
Exposure Value Compensation adjusts brightness
within the existing ISO Limit. If brightness has already
reached the ISO Limit in a low-light environment,
increasing the Exposure Value Compensation does
not have any effect.
PRO
TIP

13 14
ISO Limit adjusts the camera’s sensitivity in low-light
environments, and creates a balance between brightness and
result image noise. Image noise refers to the degree of graininess
in the image.
In low light, higher ISO values result in brighter image, but with
greater image noise. Lower values result in lower image noise,
but darker images.
ISO Limit
The FOXEER BOX can setup 3 types of metering mode:
Center-weighted metering, Multi-spot metering, Spot metering.
Metering
Setting Camera
03
TO CONNECT YOUR FOXEER BOX TO THE FOXEER APP:
1. Download the FOXEER App to your smartphone/tablet from the
Apple App Store or Google Play.
2. Follow the on-screen instructions to connect your camera to the
app. The default password for your camera is 1234567890.
Connecting to the FOXEER App
04
The FOXEER App lets you control your camera remotely using a
smartphone or tablet. Features include full camera control, live
preview, playback and sharing of content.
CHOOSE A NETWORK
FOXEER_LEGEND 3 XXXXXX
FOXEER

15 16
FOXEER is dedicated to providing the best possible service. To
reach FOXEER Customer Support, visit www.foxeer.com .
FOXEER is trademarks or registered trademarks of XAT in
China and internationally. Other names and marks are the prop-
erty of their respective owners.
Customer Support
05
Trademarks
06