Foxtech M12 User manual

M12 UAV Megaphone System
Function:
Parameter
Real-timebroacasting, 3 types of alarms and sirens,equipped with
searchlight. It also supports MP3 function, support Max 32G SD card.
：
Air end voltage: 12v-24V
Searchlight Power：
Communication distance:5km
Sound Strength：65-75db (>100
Power: 100w（standard version）
m )
12w
Modes: hard light, weak light, strobe
Search Light Control：
Air end Weight：720g
led Lumen: 3000
pwm

Installation：
111：
1: Install it to the M600, fix it with the three screw pillars under
the plate. The top of the mounting bar snaps directly to the two carbon tubes
below the M600.
2: For other models, it is generally installed and fixed under the large
center plate of the drone.
Microphone: For the specific operation of the microphone module, see the specific
I n s t r u c t i o n s :
Connect to the power supply on the air end-yellow banana plug, power supply voltage
12-24V
operation process of the handheld terminal of the microphone below;
Search Light:
After connecting the onboard power supply, connect the pwm interface to the receiver
socket (select the 2 or 3-position switch corresponding to the remote control), and use
the remote control to control the searchlight mode.
Each time the remote control is switched quickly, the light switches once between
strong light, weak light and flashing. Stay in one mode for more than 10s, when
switched again, the light will be off.

Handheld Intercom
Function：
（一）TF
Function button description:
The three yellow buttons are for
siren, fire alarm, and continuous
alarm. The two red ones below
are real-time recording and
playback buttons; the button on
the left is for real-time voice
playback, the right upper button
is power switch, and the right
bottom button is the volume
B
TF card is supported. The
handheld terminal controls
the audio playback in the TF
card. Built-in battery, easy to
Real-time recording and
playback, playback of warning
and alarm sounds.
carry.
attery capacity: 12.6v, 2200mah
adjustment knob.
Function
As shown in the figure above, turn on the power switch on the handheld
intercom to turn on the ground terminal.When switching to the TF card mode,
you can use the TF control button on the handheld terminal to control the TF
card audio, the voltage is detected battery voltage (note:the battery voltage
cannot be lower than 9.5V), and the antenna is a pulling-type antenna.

（二）Handheld Intercom
Press the TF/handheld intercom function button
to switch to the handheld intercom end. When
using the handheld intercom, first make sure
that all 5 function buttons are in the pop-up
state, and then turn on the power switch. At this
time, the power indicator light will be on, the
REC light will not be on, press and hold Play
button to speaking.The Play button is in the pop
-up state, and three kinds of alarm sounds can
be realized by pressing the three yellow
function keys. Press the Play button to speak to
realize recording, release the Play button, and
press the play button to play the recorded
sound. (Note: The function of shouting and
playing cannot be performed at the same time,
and the RECORD button and the PLAY button
must be in the up state when Speaking).
Notice：
1. The two red buttons onthe handheld are in a pop-up state, and the controller switch
button is at one end of the handheld intercom.
2. The left red button on the handheld intercom is the recording button, and the right
red one is the play button. First press the record button,then press and hold the speaking
button on the left side of the handheld intercom to speak normally (support max10
seconds), after real-time speaking, press the play button to repeat the playback.
3. TF card no more than 32G, mp3 format, bit rate less than 320kbps, switch to the TF
card end when working.

4. For the handheld antenna, it is recommended not to pull out the last two sections of
the antenna during work to ensure a better effect.
5. It is recommended to turn down the volume for short-distance tests, and turn up the
volume for long-distance tests.