Free Color W3610 User manual

FREE COLOR W3610
W 3610 - мощный светодиодный полноповортный прожектор на 10 Вт диодах
4-в-1 RGBW
Технические характеристики:
Источник:
36 светодиодов по 10 Вт 4-в-1
RGBW
Срок жизни диодов 60 000-100 000
часов
16 000 000 цветов
Оптическая группа:
Угол раскрытия луча 25°
Эффекты:
Линейный диммер 0% - 100%
Строб 1-20 Гц
Интерфейс / управление:
Мультифункциональный дисплей с
4-мя кнопками
13 каналов DMX512
Master/slave
Автоматический режим
Звуковая активация
Pan / Tilt:
540° - 270°
Автоматическое
позиционирование
Функция тонкой подстройки
Блок питания:
Вход AC 90В-220В /
50-60Гц
Потребляемая мощность
70 Вт
Разъемы:
DMX512: XLR 3-пин
Питание
Размер: 405х330х495мм
Вес: 9 кг
Комплектация:
Полноповоротный
прожектор – 1 шт.
Кабель питания - 1 шт.
Руководство пользователя
–1 шт.

1. Specification
working voltage: AC90～250V 50Hz/60Hz
power: 125W
LED spec: 36PCS of 180 RGB Led
LED Lifetime: 60,000-100,000 hours
beam angle: 25°
control signal: DMX512
control channels: 19CH(RGB)
Possible Color Combinations: 16.7 million
1. Operational approach
1.1 Button operation
❤Basic usage
Menu The main menu switch
UP Parameters adjustment
Down Parameters adjustment
Enter confirm/preserve/enter submenu
E LED display windows
For your own safety, please read this manual before installing the device. This manual
covers the important information
on installation and applications. Please install and operate the fixture with following
instructions. Meanwhile, please keep this manual well for future needs. LED moving
wash is made of a new type of high temperature strength of engineering plastics and
cast aluminum casing with nice outlook. The fixture is designed and manufactured
strictly following CE standards, complying with international standard DMX512
protocol. It’s available independently controlled and linkable with each other for
operation. And it is applicable for large-scale live performances, theater, studio,
nightclubs and discos. adopts powerful LED lamps which features high brightness and
stability.
Please carefully dispack it when you receive the fixture and check whether it is
damaged during the transportation. And please check whether the following items are
included inside the box:
Moving Head------- one Omega Clamp------one
User Manual----one
MENU UP DOWN ENTER

1. Safety Instructions
This device has left the factory in perfect condition. In order to maintain this condition
and to ensure a safe operation, it is absolutely necessary for the user to follow the
safety instructions and warning notes written in this user manual.
If the device has been exposed to temperature changes due to environmental
changes, do not switch it on immediately. The arising condensation could damage the
device. Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be
earthed.
The electric connection must carry out by qualified person. The device shall only be
used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would
be the case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power cord by the plug. Never pull out the plug by tugging the power
cord.
During initial start-up some smoke or smell may arise. This is a normal process and
does not necessarily mean that the device is defective, it should decrease gradually.
Please don't project the beam onto combustible substances. Fixtures cannot be
installed on combustible substances, keep more than 50cm distance with wall for
smooth air flow, so there should be no shelter for fans and
ventilation for heat radiation. If the external flexible cable or cord of this luminaire is
damaged, it shall be exclusively replaced by the manufacturer or his service agent or
a similar qualified person in order to avoid a hazer.
2. Operation Instructions
-The moving head is an LED wash light for onsite decoration purpose.
-Don’t turn on the fixture if it’s been through severe temperature difference like after
transportation because it might damage the light
due to the environment changes. So make sure to operate the fixture until it is in
normal temperature.
-This light should be keep away from strong shaking during any transportation or
movement.
-Don’t pull up the light by only the head, or it might cause damages to the mechanical
parts.
-Don’t expose the fixture in overheat, moisture or environment with too much dust
when installing it. And don’t lay any power cables
on the floor. Or it might cause electronic shock to the people.
-Make sure the installation place is in good safety condition before installing the
fixture.
-Make sure to put the safety chain and check whether the screws are screwed
properly when installing the fixture.

-Make sure the lens are in good condition. It’s recommended to replace the units if
there are any damages or severe scratch.
-Make sure the fixture is operated by qualified personnel who knows the fixture before
using.-Keep the original packages if any second shipment is needed.
-Don’t try to change the fixtures without any instruction by the manufacturer or the
appointed repairing agencies.
-It is not in warranty range if there are any malfunctions from not following the user
manual to operate or any illegal operation, like
shock short circuit, electronic shock, lamp broke, etc.
3. Installation via clamp
Please refer to the picture below:
Screw one clamp each via a M12 screw and nut onto the Omega holders.
Insert the quick-lock fasteners of the first Omega holder into the respective holes on
the bottom of the device. Tighten the quick-lock fasteners fully clockwise. Install the
second Omega holder.
Pull the safety-rope through the holes on the bottom of the base and over the trussing
system or a safe fixation spot. Insert the end in the carbine and tighten the safety
screw.
4. DMX-512 control connections
Connect the provided XLR cable to the female 3-pin XLR output of your controller and
the other side to the male 3-pin XLR input of the moving head. You can chain multiple
Moving head together through serial linking. The cable needed should be two core,
screened cable with XLR input and output connectors. Please refer to the diagram
below.

DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is in an electrically
noisy environment, such as in a discotheque, it is recommended to use a DMX
terminator.
This helps in preventing corruption of the digital control signal by electrical noise. The
DMX terminator is simply an XLR plug with a 120 Ω resistor connected between pins
2 and 3,which is then plugged into the output XLR socket of the last fixture in the
chain.
Please see illustrations below.
❤LED English display windows table
Channel number
Value
Function instruction
1
DMX512 ADDRESS
001
0-255 Press UP or DOWN to
adjust address code, and press
confirm to save .
2
ADJ RED LIGHT
255
0-255 Press UP or DOWN to
adjust red light and press
confirm to save .
3
ADJ GREEN LIGHT
255
0-255 Press UP or DOWN to
adjust green light and press
confirm to save .
4
ADJ BLUE LIGHT
255
0-255 Press UP or DOWN to
adjust blue light and press
confirm to save.

5
ADJ WHITE LIGHT
255
0-255 Press UP or DOWN to
adjust white light and press
confirm to save.
6
ADJ AMBER LIGHT
255
0-255 Press UP or DOWN to
adjust amber light and press
confirm to save.
7
ADJ PURPLE LIGHT
255
0-255 Press UP or DOWN to
adjust purple light and press
confirm to save.
8
SET FOCUS
0
0-255 Press UP or DOWN to
adjust focal length and press
confirm to save.
9
SIDE PROGRAM
01
0-255 Press UP or DOWN to
choose built-in program and
press confirm to save.
10
ADJUST SPEED
16
0-255 Press UP or DOWN to
choose built-in program and
press confirm to save.
11
TEST MODE
0-255 Press UP or DOWN to
enter the sound active and
self-propelled models
12
RESET ?
0-255 Press the ENTER button
to display the reset process
13
SELECT LANGUAGE
English/Chinese
In the test mode, press the arrow keys to select the voice and self-propelled. Show
time English Sound: AUDIO CONTROL; Chinese Show: Voice program
Since the travel time displayed in English: AUTO RUN; Chinese Show: self-propelled
Program
1. DMX512 18CH
Channel
number
Value
Function instruction
1
Pan
0~255
2
Tilt
0~255
3
X fine
0~255
4
Y fine
0~255
5
XY Speed
0~255 from fast to slow
6
Dimmer
0~255 R G B W A P Dimmer. Linear
dimmer. from dark to bright
7
Strobe
0-255 from slow to fast；
8
R
0－255 R dimmer. Linear dimmer. from
dark to bright
9
G
0－255 G dimmer. Linear dimmer. from
dark to bright
10
B
0－255 B dimmer. Linear dimmer. from

dark to bright
11
W
0－255 W dimmer. Linear dimmer. from
dark to bright
12
A
0－255 A dimmer. Linear dimmer. from
dark to bright
13
P
0－255 P dimmer. Linear dimmer. from
dark to bright
14
Choose the
color
0-255Change the color(0-20:R+G++ ；
21-40:R+B++；41-60:G+R++；61-80:G+B++；
81-100:B+G++ ；101-120:R+G+B++ ；
121-140:R+B+G++ ；141-160:B+G+R++ ；
161-200:R+B+G++ ；201-220:B+G+R++ ；
221-255:R+B+G++)
15
Built-in program
First 13 Channel Enable (0-75); DMX greater
than 75, each corresponding to an increase
of 10 built-in programs.
16
Speed
0-255 upward slowdowns, 0 fastest speed.
17
Focusing
(0-128) focal positioning; (129-255) focal
length from 0 to - Max constantly changing.
18
X/Y Enable
motor reversing
（0-64）No function; (65-128) X inversion;
(129-192) Y inversion; (193-255) X / Y
inversion。
19
Reset,
automatic
operation and
voice
DMX value of 10 seconds does not change
implementation procedures; (0-64) no
function; (65-128) self-propelled; (129-192)
voice; (193-255) Reset。
After moving head LED powered, turn the power console, when receiving the
DMX512 console signals, signal flags X disappears, when the control signal is
controlled station
In the address code state, multi-machine connection, if there is no access control
units, can achieve the main features from online operation in which a piece of
equipment, the rest of the state in the address of the device to follow the host
synchronization run the program. Connected control units, state of the device in the
address stage control can be controlled