FRENGER systems T60-EH User manual

T60-EH Mul-funconal controller with built-in thermostat sensor
Step 1
Loosen the screw from the boom of the controller to release
the front half. Then carefully pull and separate the front part
away from the back-plate, inially from the lower part of the
controller.
Step 2
Place the front part of the controller in a safe place, to prevent
scratches and damage. Connect the wires in accordance with
the diagram on page 2. The wiring diagram must be followed.
Step 3
Screw the controller back-plate onto the recessed juncon box
in the wall. Use the supplied screws or the original screws of the
juncon box.
Step 4
When the back-plate is secure, ret the front part carefully to
the back-plate, starng with the upper part of the controller,
and gently ghten the boom retaining screw.
The controller is now ready to operate.
MOUNTING OF THE PROGRAMMABLE CONTROLLER THERMOSTAT
The controller is designed to be ush mounted, and requires a
minimum 35 mm deep juncon box, recessed, within the wall.
PLACEMENT OF THE THERMOSTAT
The controller should be placed on the wall, approximately
1.5 m above the oor level, when the built-in sensor is used
for temperature regulaon.
Ensure and allow free air circulaon around it. Draught and
direct sunlight, or other heat sources, must be avoided. It can
aect controller funcons.
WARNING – Important Safety Instrucons
Disconnect the power supply before carrying out
any installaon or maintenance work, on this ther-
mostat and/or associated components.
The thermostat, and the associated components,
should only be installed by a qualied and author-
ized electrician.
Electrical installaon must be in accordance with
appropriate naonal regulaons.
PRODUCT PROGRAM
INSTALLATION INSTRUCTION
Thank you for the purchase of our product. Please read the
instrucons before mounng and installing.
The T60-EH is an Touchscreen Programmable Controller for
temperature control by means of NTC sensors, located either
internally within the programmable controller or can be made
compable with external sensors.
Touchscreen Programmable Control Thermostat T60-EH

Operang voltage / Power supply 85-230VAC, 50/60Hz
Standby power < 1.0W
Rated current / Relay 16A resisve load, 230V / SPST
Seng range, temperature 5-45°C
Floor limitaon, temperature range 20-45°C
On/O dierenal ±0.5°C
Humidity sensor, air 0-100%
Operang modes
Three programming modes:
Weekday/Weekend (5 + 2)
- edit/set 4 me periods per day
Seven day programming (7)
- edit/set 4 me periods per day
24 hours mode
- edit/set 4 me periods
Hold/Timer mode:
- acvate and adjust a boost period of
up to 24h, by oponal seng range
temperature
Home/Away mode:
- the controller will turn on the heat-
ing, if the room temperature drops
below the set value.
Holiday mode:
- calendar based and programmable
in advance.
OFF mode:
- frost protecon included, by adjust-
able temperature range
Baery backup 2 months
Appliance and protecon class Class II - IP20
Size (H/W/D) 86/96/44 mm
Build-in depth 30 mm
Installaon type Flush, hole pitch 60 mm
Terminals 2.5 mm², screw cage clamp
Terminal wire size max. 2.5 mm²
Display size 3.5” - Color capacive touch
Display resoluon 480x320 TFT
Oponal external oor sensor NTC (10 kΩ), Class II, 3 meter
Oponal external room/air sensor NTC (10 kΩ), Class II, 3 meter
Max. length sensor cable 50 m, 2 x 1.5 mm²
- Low Voltage Direcve 2014/35/EU
- EMC Direcve 2014/30/EU
- RoHS Direcve 2011/65/EU
- Radio Equipment Direcve 2014/53/EU
- Electrical Equipment (Safety) Regulaons 2016
- Electromagnec Compability Regulaons 2016
-
RT2RT1NNLLoad
230VAC
~~
FRENGER Systems Limited | Riverside Road | Pride Park | Derby | DE24 8HY
E - [e-mail] | T - [phone] | F - [phone]
22.03.29-V1.3
TECHNICAL SPECIFICATION
Programming and Setup
The controller carries a lot of features and sengs.
In order to access these points please contact our
technical department for a copy of the user manual.
This document will guide you through the setup of
the dierent funcons and modes.
OPERATING THE CONTROLLER
When powering up the thermostac programmable controller, it
will automacally start to run in mode with the factory sengs.
There is no mechanical ON/OFF switch. To access this feature,
simply so tap on the touchscreen and/or the symbol
External Sensor
Floor Sensor
Output, max 16A
Main Supply
230V
Wiring
Connect the wires in accordance with the diagram. The wires
must be connected as follows:
Output (neutral)
Power supply (neutral)
Power supply (live)
Output, max. 16A (3680W)
External oor sensor (hot)
External room/air sensor (hot)
Sensor connecon point (cold)
Terminal Marking
Terminal N:
Terminal N:
Terminal L:
Terminal Load:
Terminal RT1:
Terminal RT2:
Terminal - (minus):
CONNECTIONS - WIRING
-
RT2RT1NNLLoad
Model: T60
Supply voltage: 85-230V~ 50/60Hz
Rated current: 16A resistive load
Ingress protection code: IP20
RoHS