FRENGER systems T60-EH User manual

Touchscreen Programmable Control Thermostat T60-EH
Step 1
Loosen the screw from the bottom of the controller to release
the front half. Then carefully pull and separate the front part
away from the back-plate, initially from the lower part of the
controller.
Step 2
Place the front part of the controller in a safe place, to prevent
scratches and damage. Connect the wires in accordance with
the diagram on page 2. The wiring diagram must be followed.
Step 3
Screw the controller back-plate onto the recessed junction box
in the wall. Use the supplied screws or the original screws of
the junction box.
Step 4
When the back-plate is secure, refit the front part carefully to
the back-plate, starting with the upper part of the controller,
and gently tighten the bottom retaining screw.
The controller is now ready to operate.
INSTALLATION INSTRUCTION
Thank you for the purchase of our product. Please read the
instructions before mounting and installing.
The T60-EH is an Touchscreen Programmable Controller for
temperature control by means of NTC sensors, located either
internally within the programmable controller or can be made
compatible with external sensors.
PRODUCT PROGRAM
T60-EH Multi-functional controller with built-in thermostat sensor.
WARNING – Important Safety Instrucons
Disconnect the power supply before carrying out
any installaon or maintenance work,on this ther-
mostat and/or associated components.
The thermostat, and the associated components,
should only be installed by a qualied and author-
ized electrician.
Electrical installaon must be in accordance with
appropriate naonal regulaons.
PLACEMENT OF THE THERMOSTAT
The controller should be placed on the wall, approximately 1.5 m
above the floor level, when the built-in sensor is used for
temperature regulation.
Ensure and allow free air circulation around it. Draught and direct
sunlight, or other heat sources, must be avoided. It can affect
controller functions.
MOUNTING OF THE PROGRAMMABLE CONTROLLER THERMOSTAT
The controller is designed to be flush mounted, and requires a
minimum 35 mm deep junction box, recessed, within the wall.

OPERATING THE CONTROLLER
When powering up the thermostatic programmable controller,
it will automatically start to run in mode with the factory
settings. There is no mechanical ON/OFF switch. To access this
feature, simply soft tap on the touchscreen and/or the symbol
FRENGER Systems Limited | Riverside Road | Pride Park | Derby | DE24 8HY
E - [e-mail] | T - [phone] | F - [phone]
TECHNICAL SPECIFICATION
18.08.22-01EN
Operang voltage / Power supply 85-230VAC, 50/60Hz
Standby power < 1.0W
Rated Current / Relay 16A resisve load, 230V
Seng range, temperature 5-45°C
Floor limitaon, temperature range 20-45°C
On/O dierenal ±0.5°C
Humidity sensor, air 0-100%
Operang modes
Three programming modes:
Weekday/Weekend (5 + 2)
- edit/set 4 me periods per day
Seven day programming (7)
- edit/set 4 me periods per day
24 hours mode
- edit/set 4 me periods
Hold/Timer mode:
- acvate and adjust a boost period of
up to 24h, by oponal seng range
temperature
Home/Away mode:
- the controller will turn on the heat-
ing, if the room temperature drops
below the set value.
Holiday mode:
- calendar based and programmable
in advance.
OFF mode:
- frost protecon included, by adjust-
able temperature range
Baery backup 2 months
Appliance and protecon class Class II - IP20
Size (H/W/D) 86/96/44 mm
Build-in depth 30 mm
Installaon type Flush, hole pitch 60 mm
Terminals 2.5 mm², screw cage clamp
Terminal wire size max. 2.5 mm²
Display size 3.5” - Color capacive touch
Display resoluon 480x320 TFT
Oponal external oor sensor NTC (10 kΩ), Class II, 3 meter
Oponal external room/air sensor NTC (10 kΩ), Class II, 3 meter
Max. length sensor cable 50 m, 2 x 1.5 mm²
CE Direcves EMC Direcve 2014/30/EU
RoHS Direcve 2011/65/EU
Wiring
Connect the wires in accordance with the diagram. The wires
must be connected as follows:
CONNECTIONS - WIRING
Terminal Marking
Terminal - (minus):
Terminal RT2:
Terminal RT1:
Terminal N:
Terminal N:
Terminal (empty):
Terminal L:
Terminal Load:
Sensor connecon point (cold)
External room/air sensor (hot)
External oor sensor (hot)
Output (neutral)
Power supply (neutral)
Do not connect
Power supply (live)
Output, max. 16A (3680W)
Programming and Setup
The controller carries a lot of features and settings.
In order to access these points please contact our
technical department for a copy of the user manual.
This document will guide you through the setup of
the different functions and modes.
Output, max 16A
Main Supply
230V
Sensor Connection Point
(cold wire)
External Sensor
(hot wire)
Floor Sensor
(hot wire)