FRESKO CM001 User manual

CM001 Coffee maker
[e-mail]
#Version 1.0
OPERATION GUIDE
Customer Service:
1-866-211-9344

IMPORTANT SAFEGUARDS
Read all instructions.
Before using the electrical appliance, the following basic
precautions should always be followed including the
following:
Before using check that the voltage of wall outlet
corresponds to rated voltage marked on the rating
plate.
This appliance has been incorporated with a grounded
plug. Please ensure the wall outlet in your house is well
earthed.
To protect against fire, electric shock and injury to
persons do not immerse cord, plug, in water or other
liquid.
Remove plug from wall outlet before cleaning and when
not in use. Allow appliance cool down completely
before taking off, attaching components or before
cleaning.
Do not operate any appliance with a damaged cord or
plug or after the appliance malfunctions, or is dropped
or damaged in any manner. Return appliance to the
nearest authorized service facility for examination,
repair or electrical or mechanical adjustment.
The use of accessory attachments not recommended
by the appliance manufacturer may result in fire,
electric shock or injury to persons.
Place appliance on flat surface or table, do not hang
power cord over the edge of table or counter.
Ensure the power cord do not touch hot surface of
appliance.
Do not place the coffee maker on hot surface or beside
fire in order to avoid to be damaged.
To disconnect, turn any control to “off,” then remove
plug from wall outlet. Always hold the plug. But never
pull the cord.
Do not use appliance for other than intended use and
place it in a dry environment.
Close supervision is necessary when your appliance is
being used by or near children.
Be careful not to get burned by the steam.
01
Do not touch the hot surface of appliance (such as steam wand, and
the brewing filter just boiling). Use handle or knobs.
Do not let the coffee maker operate without water.
Scalding may occur if the water tank is removed during the brewing
cycles.
Do not remove the metal funnel when appliance in brewing coffee or
when steam and hot water escape from metal funnel and ensure to
release the pressure in water tank before removing metal funnel.
Connect plug to wall outlet before using and turn any switch off before
plug is removed from wall outlet.
Relief pressure through steam wand before removing tank cover or
metal funnel.
This appliance is not intended for used by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experi-
ence and knowledge, unless they have been given supervision or
instruction concerning use of the appliances by a person responsible for
their safety.
Children should be supervised to ensure that they do not play with the
appliance.
This appliance is intended to be used in household and similar applica-
tions such as:
- staff kitchen areas in shops, offices and other working environments;
- farm houses;
- by clients in hotels, motels and other residential type environments;
- bed and breakfast type environments.
Do not use outdoors.
Do not place on or near a hot gas or electric burner, or in a heated oven.
If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a
hazard.
WARNING: The filling aperture must not be opened during use.
The appliance must not be immersed
The heating element surface is subject to residual heat after use
Potential injury from misuse
The coffee-maker shall not be placed in a cabinet when in use.
Cleaning and user maintenance shall not be made by children without
supervision.

Before using check that the voltage of wall outlet
corresponds to rated voltage marked on the rating
plate.
This appliance has been incorporated with a grounded
plug. Please ensure the wall outlet in your house is well
earthed.
To protect against fire, electric shock and injury to
persons do not immerse cord, plug, in water or other
liquid.
Remove plug from wall outlet before cleaning and when
not in use. Allow appliance cool down completely
before taking off, attaching components or before
cleaning.
Do not operate any appliance with a damaged cord or
plug or after the appliance malfunctions, or is dropped
or damaged in any manner. Return appliance to the
nearest authorized service facility for examination,
repair or electrical or mechanical adjustment.
The use of accessory attachments not recommended
by the appliance manufacturer may result in fire,
electric shock or injury to persons.
Place appliance on flat surface or table, do not hang
power cord over the edge of table or counter.
Ensure the power cord do not touch hot surface of
appliance.
Do not place the coffee maker on hot surface or beside
fire in order to avoid to be damaged.
To disconnect, turn any control to “off,” then remove
plug from wall outlet. Always hold the plug. But never
pull the cord.
Do not use appliance for other than intended use and
place it in a dry environment.
Close supervision is necessary when your appliance is
being used by or near children.
Be careful not to get burned by the steam.
02
Save These Instructions
Do not touch the hot surface of appliance (such as steam wand, and
the brewing filter just boiling). Use handle or knobs.
Do not let the coffee maker operate without water.
Scalding may occur if the water tank is removed during the brewing
cycles.
Do not remove the metal funnel when appliance in brewing coffee or
when steam and hot water escape from metal funnel and ensure to
release the pressure in water tank before removing metal funnel.
Connect plug to wall outlet before using and turn any switch off before
plug is removed from wall outlet.
Relief pressure through steam wand before removing tank cover or
metal funnel.
This appliance is not intended for used by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experi-
ence and knowledge, unless they have been given supervision or
instruction concerning use of the appliances by a person responsible for
their safety.
Children should be supervised to ensure that they do not play with the
appliance.
This appliance is intended to be used in household and similar applica-
tions such as:
- staff kitchen areas in shops, offices and other working environments;
- farm houses;
- by clients in hotels, motels and other residential type environments;
- bed and breakfast type environments.
Do not use outdoors.
Do not place on or near a hot gas or electric burner, or in a heated oven.
If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a
hazard.
WARNING: The filling aperture must not be opened during use.
The appliance must not be immersed
The heating element surface is subject to residual heat after use
Potential injury from misuse
The coffee-maker shall not be placed in a cabinet when in use.
Cleaning and user maintenance shall not be made by children without
supervision.

03
(Product may be subject to change without prior notice)
BEFORE THE FIRST USE
Remove the plug at the bottom of the tank. Pour water into water tank, the water
level should not exceed the “MAX” mark in the water tank. Then close the tank cover.
Set brewing filter into metal funnel (no coffee in brewing filter).
Place an espresso cup on drip plate. Make sure the knob is at the horizontal
position(off-porition).
To ensure the first cup of coffee tastes excellent, you should rinse the coffee
maker with warm water as follows:
KNOW YOUR COFFEE MAKER
1. Power indicator / button
2. Single-cup indicator / button
3. Double-cup indicator / button
4. Steam indicator / button
5. Brewing filter
6. Metal funnel
7. Funnel handle
8. Drip plate
9. Drip tray
10. Tank cover
11. Handle
12. Water tank
13. Knob
14. Steam handle
15. Steam wand
16. Measuring spoon
Note: the appliance is supplied with a water tank for easy cleaning, you
fcan ill the water tank with water firstly, and then put the water tank into
the appliance.
Note: the appliance is not equipped with jug, please use your jug or coffee
cup.
Connect to power source, press the power button“ ”. The power indicator will
be illuminated and single/double-cup/steam indicator will flashing.
The appliance will start heating,When single/double-cup/steam indicator
becomes solid, it shows the pre-heating is finished. Press double-cup button, wait
for a moment, The water will flow out.
When the appliance stops pumping water automatically, you can pour the
water in container out then clean them thoroughly, now you can start brewing.
1
10
11
12
13
14
15
16
2
3
4
5
6
7
8
9

04
PRE-HEATING
MAKE ESPRESSO COFFEE
Remove the funnel by turning it in clockwise, Add ground coffee to brewing filter
with measuring spoon, a spoon ground coffee power can make about a cup of
top-grade coffee, then press the ground coffee powder tightly with the measuring
spoon.
Set brewing filter into metal funnel, make sure the tube on the funnel aligns with
groove in the appliance, then insert the funnel into the appliance as indicating of
“LOCK”mark, and you can fix them into coffee maker firmly through turning it
anticlockwise until it is at the “CLOSE” position .
Then place the hot cup on drip plate.
Select single cup“ ” or double-cup “ ” according to your demand and then
press the corresponding button of the selected function. After waiting for a
moment, there will be coffee flowing out.
The appliance will stop working when the coffee-brewing is finished, and then
your coffee is ready now.
After finishing making the coffee, you can take the metal funnel out through turn
clockwise, then pour the coffee residue out.
Remove the water tank and open the tank cover to fill it with desired water, the
water level should not exceed the “MAX” mark in the water tank. Then place the
water tank into the appliance properly.
Set brewing filter into metal funnel, make sure the tube on the funnel aligns with
groove in the appliance, then insert the funnel into the appliance from the “LOCK”
position, and you can fix them into coffee maker firmly through turn it anticlock-
wise until it is at the“CLOSE” position.
Place an espresso cup on drip plate.
Then connect the appliance to power supply source. Make sure the knob is at the
horizontal position(off-porition).
Press the power button“ ”, The power indicator will be illuminated and
single/double-cup/steam indicator will flashing.
When single/double-cup/steam indicator becomes solid, it shows the pre-heating is finished.
To make a cup of good hot Espresso coffee, we recommend you preheating the
appliance before making coffee, including the metal funnel, brewing filter and
cup, so that the coffee flavour can not be influenced by the cold parts.
Note:
There may be noise when pumping the water on the first time, it is
normal, the appliance is releasing the air in the appliance. After about
20s, the noise will disappear.
WARNING:
Do not leave the coffee maker unattended during making the coffee, as
you need operate manually sometimes!

FROTHING MILK/ MAKE CAPPUCCINO
Method:
You get a cup of cappuccino when you top up a cup of espresso with frothing milk.
Note: Before frothing milk, release steam for 10 seconds, during making steam, the
metal funnel must be assembled in position.
Press the steam button “ ”, the steam indicator will flashing. When steam
indicator becomes solid, the pre-heating is finished.
Prepare espresso first with container big enough according to the part “MAKE
ESPRESSO COFFEE”.
Fill a jug with about 100 grams of milk for each cappuccino to be prepared, you
are recommended to use whole milk at refrigerator temperature (not hot!).
Note: In choosing the size of jug, it is recommended the diameter is not less than
70±5mm, and bear in mind that the milk increases in volume by 2 times, make
sure the height of jug is enough.
Insert the steam wand into the milk about two centimetre, then turn the knob to
the “ ” position, steam will come out from the steam outlet. Froth milk in the
way moving vessel round from up to down.
Warning: Be sure to operate carefully as the steam may result in scald to person.
When the required purpose is reached, you can turn the knob off.
Note: Clean steam outlet with wet sponge immediately after steam stops
generating, but care not to hurt!
Pour the frothed milk into the espresso prepared, now the cappuccino is ready.
Sweeten to taste and if desired, sprinkle the froth with a little cocoa powder.
The steam wand can be used to froth milk singly or make hot beverages like
drinking chocolate and water.
Note: After making steam, you can press “Single-cup” or “Double-cup” button
immediately to brew coffee again. The coffee indicator will flasing quickly if the
temperature is too high, at this time, you need to reduce the temperature by
following the operation as below. Turn the knob to “Hot water” setting “ ”, and
then the hot water will dispense. When the temperature goes down ,the pump
will stop automatically and you should turn the knob off , then you can brew
coffee again.
Note: If you do not want to brew coffee when the high-temperature warning
occurs, you can press the “Single-cup” or “Double-cup” button again to cancel.
05
MAKE HOT WATER
After finish preheating, turn the knob to “ ” position, and then the hot water will
dispense from steam wand. When desired amount of hot water is got, turn the
knob off. Before making hot water, put a cup under the steam wand.

06
AUTOMATICALLY POWER-OFF FUNCTION
After pressing power button, if there is no any operation within 29 minutes, the
unit will power off automatically.
After pressing power button, if there is no any operation after pump puming
about 215ml water , the pump will stop automatically.
After pressing power button, if there is no any operation after pump worked
for 180s during froth milk, the pump will stop automatically.
CLEAN AND MAINTENANCE
Cut off power source and let the coffee maker cool down completely before
cleaning.
Clean housing of coffee maker with moisture-proof sponge often and clean
water tank, drip tray and drip plate regularly then dry them.
Note: Do not clean with alcohol or solvent cleanser. Never immerse the housing
in water for cleaning.
SET THE DISPENING AMOUNT
Dispensing amount of single cup
Hold and press the “Single-cup” button for 3 seconds to enter into the mode of
setting the dispensing amount. And then press the “Single-cup” button again, the
coffee starts to dispense and the “Single-cup indicator” flashes at the same time,
when the desired amount is got, press the “Single-cup” button again, the coffee
stops dispensing. At that time, the setting for the dispensing amount of single cup
is finished and it will be saved for next operation.The adjustable dispensing
amount of single cup ranges between 25ml and 60ml.
Dispensing amount of double-cup
Hold and press the “Double-cup” button for 3 seconds to enter into the mode of
setting the dispensing amount, then follow the operation of setting the dispensing
amount of single cup. The adjustable dispensing amount of double-cup ranges
between 70ml and 110ml.
Restore factory setting
Simultaneously hold and press the “Single-cup” and “Double-cup” buttons for 3
seconds to recover the factory setting of dispensing amount.
Detach the metal funnel by turning it clockwise, get rid of coffee residue inside,
then you can clean it with cleanser, but at last you must rinse with clear water.
Clean all the attachments in the water and dry thoroughly.

07
Cut off power source and let the coffee maker cool down completely before
cleaning.
Clean housing of coffee maker with moisture-proof sponge often and clean
water tank, drip tray and drip plate regularly then dry them.
Note: Do not clean with alcohol or solvent cleanser. Never immerse the housing
in water for cleaning.
CLEANING MINERAL DEPOSITS
To make sure your coffee maker operating efficiently, internal piping is cleanly and
the peak flavor of coffee, the coffee machine needs to be descaled, cleaned and
maintained periodically. descaling warning will be shown when the appliance has
cumulatively worked for 500 cycles, at that time, all indicators will flash for 5
times, which means that the coffee machine needs to be performed descaling,
and then the appliance will go back into normal condition. descaling warning will
be shown each time when you turn on the appliance if you do not cancel.
Fill the water tank with water and descaler to the MAX level ( the scale of water
and descaler is 4:1, the detail refers to the instruction of descaler. Please use
“household descaler”, you can use the citric acid (obtainable from chemist’s or
drug stores) instead of the descaler (the one hundred parts of water and three
parts of citric acid).
Press “Double-cup” button once to make coffee and make hot water for about
100ml. Then turn off the appliance and leave the descaling solution in the appli-
ance for 5 minutes.
Turn on the appliance and repeat the Step 3 for 3 times.
Repeat the steps of 3 for 2 times with tap water in the MAX level (it is not neces-
sary to wait for 5 minutes).
After finish descaling, you need to cancel the descaling warning: Simultaneously
hold and press the “Single-cup button”, “Double-cup button” and “steam button ”
for 3 seconds.
Detach the metal funnel by turning it clockwise, get rid of coffee residue inside,
then you can clean it with cleanser, but at last you must rinse with clear water.
Clean all the attachments in the water and dry thoroughly.

08
Do not take apart the appliance by yourself if the cause of failure is not found,
you had better contact certified serving center.
TROUBLE SHOOTING
Cause CorrectionsSymptom
Water leaks from the bottom
of coffee maker.
Please clean the drip tray.
Get rid of them.
There is much water in the drip tray.
Please contact with the authorized
service facility for repairing.
Use high and narrow cup.
Use whole milk or half-skimmed milk.
Reset knob to off position.
Reset knob to off position.
Turn knob to “ ” positon, perform
cooling operation.
Reset knob to “OFF” position.
Clean coffee maker per the content
in “before the first use” for several times.
Plug the power cord into a wall outlet
correctly, if the appliance still does
not work, please contact with the
authorized service facility for repairing.
Only after the white indicator is
illuminated, the steam can be used to froth.
Please use fresh coffee powder, or
store unused coffee powder in a cool,
dry place. After opening a package of
coffee powder, reseal it tightly and store
it in a refrigerator to maintain its freshness.
The coffee maker is malfunction.
There is some coffee powder on
filter edge.
No clean correctly after cleaning
mineral deposits.
The power outlet is not plugged well.
The white indicator is not illuminated.
The container is too big or the shape
is not fit.
You have used skimmed milk.
Make steam for 180s and the knob
is not reset.
Bolier temp is too high.
The knob is not reset to off position,
but the machine turned on.
Make hot water for 215ml and the
knob is not reset.
The knob is not reset after cooling
down.
The coffee powder is stored in a
hot, wet place for a long time. The
coffee powder turns bad.
Water leaks out of outer side
of filter.
Steam indicator blinking quickly
Acid (vinegar) taste exists in
Espresso coffee.
The coffee maker cannot
work any more.
The steam cannot froth.
Single-cup indicator and
double-cup indicator blinking
quickly
Single-cup indicator or double
-cup indicator blinking quickly
Single-cup indicator 、double
-cup indicator and steam
indicator blinking quickly
Need to descaling
ALL indecator blinking at the
same time for 5 times
Decalcifying