Friant FMA-D User manual

100
100
75
75
Step 2A: Clamp Option
1
4
C
F
D
5
6
F
DESK
Tighten
Step 2B: Grommet Option
Step 1:
Make sure there are VERSA holes
(100 x 100mm or 75 x 75mm). Then,
remove the original fixed base of the
monitor. Make sure you are careful
not to scratch the monitor screen.
Parts:
1. Dual monitor arm (1)
2. cable cover (1)
3. anti-slip rubber clamp (1)
4. bottom support clamp (1)
5. anti-slip rubber clamp (4)
6. knob (1)
7. bottom support grommet (1)
8. screw (1)
9. anti-slip rubber grommet (2)
10. pressure plate (1)
11. knob nut (1)
12. bottom support verity (1)
13. block verity (2)
Ax4
M4x12mm
Bx4
M5x12mm
Cx3
M6x12mm
Dx2
M6x10mm
Fx8 Gx1
4X4
Hx1
5X5
Cx3 Dx2 Fx1
4X4
Cx3 Fx1
4X4
8
7
1
C
F
DESK
Size of the hole:8.5-70mm
3
9
10
DESK
11
Tighten
Use supplied allen wrench
to attach to bottom
support clamp with M6x
12mm screws (3).
1 2 3 4
Attach anti-slip
rubber clamp to
the bottom of the
monitor arm.
3
Using the allen wrench, attach
the knob to the bottom
support using M6x 10mm (2)
screws. Place anti-slip rubber
on top of the installed knob.
Insert desktop in the gap
between the monitor arm
and the bottom support.
Place the cable cover over
exposed cables.
Fits worksurface
thickness:
3/4” - 4”
Insert screw into bottom support
grommet. Use allen wrench to
attach bottom support grommet
to monitor arm by using M6x
16mm screws (3).
Attach monitor arm to desk, by
inserting the base with the screw
into the predrilled hole. Before you
merge your monitor arm and your
desk, make sure you are using the
anti-slip rubber grommet.
Attach anti-slip rubber grommets
(2) to the pressure plate. Attach
the pressure plate to the bottom
of the worksurface by screwing
everything together with the
knob nut.
MONITOR ARM
DUAL
INSTALLATION
CLAMP
GROMMET
VERITY
1 2 3
Fits worksurface
thickness:
3/4” - 4”
NOTE
Cx3 Dx2 Fx1
4X4
3
5
6
8
7
9
10
11
24
12
13

Step 3: Install monitor to plate (2)
Increase washer(F) based
on actual situation
E
G
A/B
A/B
E
Using M4x 12 mm or M5x
12mm screws, screw into the
top holes on the back of the
monitor.
Position monitior by aligning
screws with grooves in the
upper corners of the monitor
attachment bracket.
Using the bolts (2) and M4x
12mm (2) or M5x 12mm (2)
to secure the monitor to the
monitor arm.
2
±180°
-85°~15°
G
±90°
±180°
±180°
-85°~15°
±180°
G
DESK
Step 4: Adjust the monitor
Adjust the monitor’s height after installing.
If the monotior is not at your desired
height, please use the 5x5 allen key to
adjust the screw on the arm. In order
to make the weight of the mount and
the monitor arm equal (so it can stop
at any height), please adjust the screws
accordingly; “-” direction in order to move
the monitor up and “+” direction to move
the monitor down.
Step 2C: Verity Track
Attach the bottom support
verity to the monitor arm
with screws (3).
Insert the blocks (2) into the Verity
track. Then, using screws, attach the
monitor arm bottom support to the
blocks (2).
Final installation shown.
1
1
2
2
3
3
12 13