Frico TAP16R User manual

TAP16R
MANUAL
MANUAL
BRUKSANVISNING
KÄYTTÖOHJE
MANUEL
BETRIEBSANLEITUNG
HANDMATIG
MANUALE
MANUAL DE INSTRUCCIONES
INSTRUKCJA
РУКОВОДСТВО ДЛЯ
EN
SE
NO
FI
FR
DE
NL
IT
ES
PL
RU

2
General instructions
Read these instructions carefully before
installation and use. Keep this manual
for future reference.The product may
only be used as set out in the assembly
and operating instructions. The war-
ranty is only valid if the product is
used in the manner intended and in
accordance with the instructions.
Important The underoor heating system
is an electrical power installation and must
therefore be installed in accordance with the
current regulations and under the supervision
of a qualied electrician.

3
EN
This is TAP16R
In the box
Installing TAP16R
Getting started
How TAP16R works
Symbols on the display
How to set TAP16R
Energy saving programs
Troubleshooting
Technical specications
............................................. 4
..................................................... 5
....................................... 6
........................................... 8
................................... 9
......................... 16
................................. 17
...................... 21
..................................... 26
....................... 27

4
This is TAP16R
TAP16R is a microprocessor-controlled
thermostat with LCD display. The dis-
play is backlit and stays lit for 30 sec-
onds after the last push of a button.
The front is tted with an LED and three
control buttons.
There are a number of temperature re-
duction programs to choose from for
energy-smart heating. It is also possible
to adjust the programming to suit your
own heating needs. The adaptive fun-
ction means that the thermostat col-
lects data from the time it is started up
and uses this to calculate when to turn
on.
Temperature control is done with an
algorithm using fuzzy logic. This techni-
que reduces temperature uctuations
and thereby provides a more even tem-
perature and lower energy consump-
tion.

5
EN
In the box
1
2
3
4
5
1. Front for Schneider Exxact (RAL 9003)
2. Frame
3. Thermostat
4. Heightening frame
5. Connection clip
Manual
Quick guide

6
Installing TAP16R
Important TAP16R must not be located
somewhere it is exposed to the
following:
• direct sunlight and draughts.
• extreme uctuations in temperature
or high air humidity (IP21).
All tubes leading into the appliance box
must be sealed so that the air tem-
perature sensor cannot be aected by
draughts.
Installation
Mount TAP16R in a standard 65 mm
junction box or in the included heigh-
tening frame.
1. Make sure the box is level with the wall.
2. Take o the front and frame by press-
ing in the latch on the right-hand side
with a chisel or similar tool, as shown in
the illustration.
3. Connect the power, connection vol-
tage 230 V/AC The protective conduc-
tor is connected with a coupling clamp
in the box. See the wiring diagram at
the right.

7
EN
4. Insert the thermostat into the ap-
pliance box and screw tight with the
existing screws.
5. Fit the frame and front.
6. If the thermostat is mounted in a
multi-compartment frame, the internal
corners of this frame must be removed.
External sensors (NTC 10 kΩ) are
available as accessories.
LOAD LOAD
N
L
SENSOR SENSOR
DO NOT USE
230 V

8
Getting started
There is a quick guide so that you can
easily get started with TAP16R.
You will nd it in the box. The guide
describes the most important
functions and settings.

9
EN
LED
Select button
Dag
Time
Temp
Selected control
How TAP16R works
This section describes all you need
to know about how Tap16R works. To
learn how to enter settings to suit your
own requirements, read the section
How to set TAP16R.
Display
Turn on the LCD display’s backlight by
pressing any button. The display stays lit
for 30 secs after the last push of a button.
When TAP16R is started for the rst
time the display shows the factory
settings as in the illustration.

10
How to enter personal settings is
described in the section How to set
TAP16R.
There is an explanation of the symbols
on the display in the section Symbols.
Using the buttons
The buttons are used to raise and lower
the temperature as well as navigating
the menus.
You access the menus by pressing
the select button . Use the arrows to
navigate to a menu option and then
conrm with to select it. The menu
system is a scrolling system, in other
words you come to all submenus re-
gardless of the direction you start from.
If you want to exit a menu, navigate
until the display shows END. Then
press the select button . You can also
wait for 30 secs and the menu will end
automatically. How to navigate the
menus is described in the section How
to set TAP16R.
Turning TAP16R o and on
To enter standby mode, keep the select
button depressed for 4 seconds.
Return to normal mode by depressing
for another 4 seconds.