Frigidaire FPHD2481KF - Professional 24" -Built User guide

Trouble Shooting TipsExploded View of Wash System
Tub and Door Seal
The door seal is pressed into the tub channel for
an interference fit. To install the seal, locate the
center mark on the seal back and press into
Product Specifications
Electrical
Rating ...................................120 Volts, 60Hz
Separate Circuit..15 amp min.- 20 amp max.
Motor (Amps) ........................................... 1.8
Heater Wattage ....................................... 900
Total Amps (load rated) ......................... 10.0
TempAssure .............................. 140°F ±5°F
(60°C±3°C) [with outer door in place]
TempBoost............. 145°F ±5°F (63°C ±3°C)
Heated Wash/Heated Rinse
Sanitize .................. 150°F ±5°F (66°C ±3°C)
Hi-Limit Thermostat ................ 200°F (93°C)
Water Supply
Suggested minimum incoming water
temperature ............................. 120°F (49°C)
Pressure (PSI) min./max. ................... 20/120
Connection (NPT) ..................................... 3/8"
Consumption (Normal Cycle) .......................
............. 4.9 - 9.7 U.S. gal., 18.5 - 36.7 liters
Water valve flow rate (U.S. GPM) ........... .83
Water recirculation rate (U.S. GPM) ..............
.................................................... approx. 12
Water fill time ..................................... 87 sec.
To replace dispenser:
• shut off electricity to dishwasher,
• remove outer door panel assembly,
• disconnect wiring to the actuator,
• remove the six screws,
• remove the dispenser,
• replace and reinstall screws,
• rewire actuator.
Check the Following
1. Fuse (blown or tripped).
2. 120 VAC supply wiring connection
faulty.
3. Electronic control board defective.
4. No 12 VAC power to control.
5. Motor (inoperative).
6. Door switch (open contacts).
7. Door latch not making contact with
door switch.
8. Touch pad circuit defective.
9. No indicator lamps illuminate when
START or OPTIONS are pressed.
1. Motor (bad bearings).
2. Motor stuck due to prolonged
non-use.
1. Improper voltage.
2. Motor windings shorted.
3. Glass or foreign items in pump.
1. Heater element (open).
2. Electronic control board defective.
3. Wiring or terminal defective.
4. Hi-Limit thermostat defective.
1. Latch mechanism defective.
2. Electronic control board defective.
3. Wiring or terminal defective.
4. Broken spring(s).
5. Defective actuator.
1. Drain restricted.
2. Electronic control board defective.
3. Defective drain pump.
4. Blocked impeller.
5. Open windings.
6. Wiring or terminal defective.
1. Water supply turned off.
2. Defective water inlet fill valve.
3. Check fill valve screen for
obstructions.
4. Defective float switch.
5. Electronic control board defective.
6. Wiring or terminal defective.
7. Float stuck in “UP” position.
1. Drain hose (high) loop too low.
2. Drain line connected to a floor drain
not vented.
1. Detergent allowed to stand too long in
dispenser.
2. Dispenser wet when detergent was
added.
3. Detergent cover held closed or blocked
by large dishes.
4. Improper incoming water
temperature to properly dissolve
detergent.
5. See "Detergent cover will not open."
Always disconnect the dishwasher from the electrical power source before adjusting or
replacing components.
Personal Injury Hazard
is attached by a worm gear clamp to the discharge
end of the drain pump.
The drain hose must have a loop at a
minimum
height of 32 inches
in order to insure proper
drainage.
The main pump can easily be removed by
disconnecting the upper spray arm supply tube
hose, the drain pump connector hose, the wiring
harness connections made at the circulation
motor, the water heat thermistor located on the
bottom of the pump and rotating the four sump
retainers toward the middle of the sump.
Pump Assembly
The pump assembly is driven by a synchronous
motor. Rotation is in the counterclockwise
direction at 3600 RPM. The motor drives a pump
which supplies 100 percent filtered water at a
rate of approximately 12 GPM to one spray arm
at a time. The spray arm’s operation is alternated
by small “pauses” of the motor during the wash
cycle.
Draining is accomplished by using a small
separate synchronous drain pump mounted to
the side of the sump. The drain pump is
connected to the main pump by a small rubber
hose. The drain check valve is located at the
discharge end of the drain pump. The drain hose
Short Turn
Gasket Cross Section
Detergent and Rinse Aid Dispenser
The detergent and rinse aid dispenser is a one
piece component consisting of a molded
detergent cup and a built-in rinse aid dispenser.
The detergent cup has a spring loaded cover
and the rinse aid dispenser has a removable
cover.
Liquid rinse aid is added to the dispenser up to
the fill line indicator. The amount of rinse aid
released can be adjusted by turning the arrow
indicator from one, being the least amount, to
four, being the greatest amount.
Mounting
Rib
Tub
Interior
Remedy
1. Replace fuse or reset breaker.
2. Repair or replace wire fasteners at
dishwasher junction box.
3. Replace control board.
4. Replace control board.
5. Replace motor/impeller assembly.
6. Replace latch assembly.
7. Replace latch assembly.
8. Replace console assembly.
9. Replace console assembly.
1. Replace motor assembly.
2. Rotate motor impeller.
1. Check voltage.
2. Replace motor/impeller assembly.
3. Clean and clear blockage.
1. Replace heater element.
2. Replace control board.
3. Repair or replace.
4. Replace thermostat.
1. Replace dispenser.
2. Replace control board.
3. Repair or replace.
4. Replace dispenser.
5. Replace dispenser.
1. Clear restrictions.
2. Replace control board.
3. Replace pump.
4. Check for blockage, clear.
5. Replace pump assembly.
6. Repair or replace.
1. Turn water supply on.
2. Replace water inlet fill valve.
3. Disassemble and clean screen.
4. Repair or replace.
5. Replace control board.
6. Repair or replace.
7. Clean float.
1. Repair to proper
32-inch minimum
height
.
2. Install air gap at counter top.
1. Instruct customer/user.
2. Instruct customer/user.
3. Instruct customer/user on proper
loading of dishes.
4. Incoming water temperature of
120°F is required to properly
dissolve dishwashing detergents.
Symptom
Dishwasher will not operate when
turned on.
Motor hums but will not start or run.
Motor trips out on internal thermal
overload protector.
Dishwasher runs but will not heat.
Detergent cover will not latch or
open.
Dishwasher will not pump out.
Dishwasher will not fill with water.
Dishwasher water siphons out.
Detergent left in dispenser.
Standard Dry Air Flow
When the control advances to the “dry” portion of
the cycle, a vent actuation solenoid is closed.
This opens the vent valve and starts the vent fan
both located in the top right rear corner of the tub.
The fan draws in the air from outside the tub,
forcing the hot, humid air down and out the
020905
bottom of the outer door panel. This outside,
cooler, dryer air helps to speed evaporation of
water from the hot dishes. At the same time the
heating element is continually cycled on and off.
On some models the dry portion of the cycle can
be extended to improve drying performance.
place. Next, install the bottom of the seal by
creating a short turn at the bottom of the tub
channel and ensuring the seal extends to the
locator ridge at the bottom of the tub. Then align
and gently press the seal into the channel in only
a few spots. Next, close and latch the door to
allow the gasket to seat properly into the channel.

Hall sensor
Cycle Selection Options
SERVICE DAT
ASHEET
P/N: 154768201
E
lectronic Series
BK.......................... Black
BU............................Blue
PK............................Pink
R...............................Red
R-BK...............Red/Black
W............................White
Wiring Diagram
Display Codes (LED)
To star t
To dela y start
Close and latch door. Press START/CANCEL pad.
Close and latch door. Press DELAY START pad to
select desired delay time.
To sele ct a new
cycle or option Press desired cycle and/or option pad. The indicator
lights will change. Press START/CANCEL within 15
seconds to begin cycle.
To canc el cycl e Press START/CANCEL. Dishwasher will drain for
90 seconds, then shut off.
For controls
lock ...........
Press and hold the RINSE ONLY or AIR DRY
pad for 3 seconds. To unlock, press and hold the
RINSE ONLY or AIR DRY pad for 3 seconds.
SENSING
WASHING
SANITIZED
DRYING
CLEAN
OPTION LED's Flashing
STATUS LED's Flashing
----------------------Turbidity sensor is checking the condition of the wash/rinse water.
No sensing for LIGHT WASH (UPPER RACK), LIGHT WASH (LOWER RACK) and CHINA/CRYSTAL.
----------------------Wash portion of cycle.
--------------------The SANITIZED criteria has been met. Indicator light will switch off when door is opened.
------------------------ Drying portion of cycle.
------------------------ Shows completion of cycle. Indicator light will switch off when door is opened.
-- HI-TEMP WASH and NO HEAT DRY/POWER DRY OFF LED's flashing indicates power failure has
occurred. Press START/CANCEL pad and reselect desired options and cycle.
-- The STATUS LED's that are lit when the door is opened will flash. Close door.
RINSE AGENT LOW ------- The liquid rinse agent is low. Light will switch off after 5 complete wash cycles or dispenser is
filled.
This information is intended for use by persons having electrical and mechanical training and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. Electrolux Home Products North America cannot be responsible,
nor assume any liability, for injury or
damage of any kind arising from the use of this Service Data Sheet.
Operation
or LO..Low liquid in the rinse aid dispenser
..........A power failure has occurred
.........Water heating delay
..........Close and latch the door
ER/ER....Switch Failure
....Hour(s) delay before start
PF
HO or Hd
CL
'01-24'
ER/CE....Configuration Error
ER/uo.....Vent will not close
ER/uF.....Fan not running
PUMP MOTOR
DRAIN MOTOR VIO
120VAC
60HZ
USER INTERFACE SWITCH
ELECTRONIC CONTROL BOARD
P3-2
P6
BU
DISPENSER R-Y
WP3- 3
W W
HEATER W
HI-LIMIT
THERMOSTAT
TURBIDITY SENSOR/
THERMISTOR
RP1
WATER VALVE
FLOAT
SWITCH PK P3- 1
W
Y
P3-7 P3-8
RINSE AID
LEVEL SENSE
BK BK P2- 8
P2- 7
P3-4
P-5
P3-6
DOOR
SWITCH
W
NEUT W L1 BK
BK BK
P3-5
P1
BK
P2-1
W
P2-2
R
P2-3
W
To activate Water/Service Test
place unit in Power Failure or
Idle Mode and then press two
padssimultaneously for 3seconds.
For Professional Seriesunitspress
DRY and START/CANCEL.
Water/Service Test
27
45
0.4
75
60
90
90
447
60 1
1
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
1
1
0
0
0
1
1
1
0
X
1
1
0
0
0
1
0
0
0
1
1
1
1
1
0
0
0
0
0
1
00
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
1
1
1
0
0
0
0
0
1
1
2
3
4
FILL/DISPENSER
STEP TOTAL TIME (SEC) WATER VALVE CIRCULATION MOTOR DRAIN MOTOR HEATER DISPENSER FAN UNIT SENSING LED WASHING LED SANITIZED LED DRYING LED
CLEAN LED
FILL
WASH/HEAT
PAUSE
WASH/HEAT
WASH/HEAT/DISP.
DRAIN
DRY
TOTAL
CLEAN LED stays on until door is opened or cycle is started.
X - denotes selectable option
5
6
7
8
0
0
0
0
0
0
1
0
(Some models)
(Some models)
0
0
0
0
0
0
P2- 4
P2- 5 P2- 6
BK
W
R
*HALL SENSOR
DISPLAY
Y/BL P2-13
P2-12
BK-W
P2-11
R
P32-6
BK
P32-9
FAN DRY UNIT
R-W
RINSE LED
SENSING LED
0
0
0
1
1
0
0
0
1
RINSE LED
Device being monitored
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
Fan damper
Display flashes when Detection of failure
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
0
0
0
1
1
0
0
0
1
Turbidity
Fan speedFan speed
Rinse aid
Thermistor
Uo
Tu
HS
UF
HS
Th
RA
Color Code
Display Codes (Readout)
Y-BK.............Yellow/Black
* Not available on the FGBD2441K
For Gallery Seriesunitspress
SANITIZE and START/CANCEL.
The dishwasher will then step
through the test cycle per the chart.
Pushing the START/CANCEL pad
will advance the dishwasher to the
next step.