Frigidaire LGHN2844MP5 User manual

Controls ..............
Automatic Ice Maker ............................... 17
www.frigidaire.com USA1-800-944-9044 www,frigidaire,ca Canada 1-80t

Pleasereadallinstructionsbeforeusingthis
refrigerator.
For your Safety
DO NOT store or use gasoline, or other
flammable liquids in the vicinity of this or
any other appliance. Read product labels
for warnings regarding flammability and
other hazards.
DO NOT operate the refrigerator in the
presence of explosive fumes.
Avoid contact with any moving parts of
automatic ice maker.
Remove all staples from the carton. Staples
can cause severe cuts, and also destroy
finishes if they come in contact with other
appliances or furniture.
Definitions
_lbThis is the safety alert symbol. It is used to
alert you to potential personal injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER indicatesan imminentlyhazardous
situation which, if not avoided, will result in
death or serious injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, could result
in death or serious injury.
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or"modera !n!u_:.................................................................................
IMPORTANT indicatesinstallation,operation
or maintenance informationwhich is
Doors
Q Handles are secure and tight
[] Door seals completely to cabinet on all
sides
[] Freezer drawer is level across the top
Leveling
Q Refrigerator is level, side-to-side and
tilted 1/4inch (6 mm) front-to-back
[] Toe grille is properly attached to
refrigerator
[] Cabinet is setting solid on all corners
Electrical Power
[] House power turned on
[] Refrigerator plugged in
Ice Maker (select models)
[] House water supplyconnected to
refrigerator
[] No water leaks present at all
connections - recheck in 24 hours
[] Ice maker is turned ON
Final Checks
[] Shippingmaterial removed
[] Fresh food and freezer temperatures
set
[] Crisper humidity controls set
[] Registration card sent in
Child Safety
Destroy or recycle the carton, plastic bags, and
any exterior wrapping material immediately
after the refrigerator is unpacked. Children
should NEVER use these items to play.
Cartons covered with rugs, bedspreads, plastic
sheets or stretch wrap may become airtight
chambers, and can quickly cause suffocation.
Proper Disposal of your
Refrigerator or Freezer
Risk of child entrapment
Child entrapment and suffocation are not
problems of the past. Junked or abandoned

refrigeratorsorfreezersarestilldangerous
- eveniftheywillsitfor"justafewdays':If
youaregettingridofyouroldrefrigeratoror
freezer,pleasefollowtheinstructionsbelowto e
help prevent accidents.
Proper Disposal of Refrigerators/Freezers
We strongly encourage responsible appliance
recycling/disposal methods. Check with your
utility company or visit www.energystar.gov/
recycle for more information on recycling your
old refrigerator.
Before you throw away your old
refrigerator/freezer:
• Remove doors.
Leave shelves in
place so children
may not easily
climb inside.
Have refrigerant
removed by a
qualified service
technician.
Unplug the refrigerator before cleaning
and before replacing a light bulb to avoid
electrical shock.
Performance may be affected if the voltage
varies by 10% or more. Operating the
refrigerator with insufficient power can
damage the compressor. Such damage is
not covered under your warranty.
Do not plug the unit into an electrical outlet
controlled by a wall switch or pull cord to
prevent the refrigerator from being turned
off accidentally.
Pressing and holding the On/Off button
for 3 seconds, located on the left side of
the temperature control panel will disable
your refrigerator's cooling system, but does
not disconnect the power to the light bulb
and other electrical components. To turn off
power to your refrigerator you must unplug
the power cord from the electrical outlet.
Grounding type wail receptacle
These guidelines must be followed to ensure
that safety mechanisms in this refrigerator
will operate properly.
Electrical information
• The refrigerator must be plugged into
its own dedicated 115 Volt, 60 Hz.,
15 Amp, AC only electrical outlet. The
power cord of the appliance is equipped
with a three-prong grounding plug for your
protection against electrical shock hazards.
It must be plugged directly into a properly
grounded three prong receptacle. The
receptacle must be installed in accordance
with local codes and ordinances. Consult
a qualified electrician. Avoid connecting
refrigerator to a Ground Fault Interrupter
(GFI) circuit. Do not use an extension
cord or adapter plug.
•If the power cord is damaged, it should
be replaced by an authorized service
technician to prevent any risk.
•Never unplug the refrigerator by pulling on
the power cord. Always grip the plug firmly,
and pull straight out from the receptacle to
prevent damaging the power cord.
/ii_i_i
Power cord with
3-prong gounded plug
To avoid personal injury or property
damage, handle tempered glass shelves
carefully. Shelves may break suddenly if
nicked, scratched, or exposed to sudden
temperature change.

•Features may vary according to model
SpilISafe TM
Shelves
Crisper
Drawer m
Deli
Drawer
i_!!iTM
*incandescent Light
Flipper GL *LED Light
i I
i I
Water
Dairy
Compartment
ir Filter
pilISafe"
Shelves
,-==Flipper
MuIHon
Crisper
->==Drawer
Door
Bin
Adj Freezer Baskets
Hinges Maker
Toe
Features not included with your refrigerator can be purchased at www.frigidaire.com or by
calling 1-800-944-9044.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii i:! ;i!i t i ! i:iI!i!i ii!ii ii!ii!ii!i!
Required Tools
You will need the following tools:
Tools Necessary:
Phillips TM
Head or
#2 Square
Drive -Head 3/8" Fixed Wrench
Components Provided:
Top Hinge\ _ _ Top Hinge
Cover Front_
Screw U _j Cover Rear
_Screw
Top
Hinge Lower
Screw Hinge
Screw
This Use & Care Guide provides general
installation and operating instructions for
your model. We recommend using a service
or kitchen contracting professional to install
your refrigerator. Use the refrigerator only as
instructed in this Use & Care Guide. Before
starting the refrigerator, follow these
important first steps.
Location
Choose a place that is near a grounded,
non-GFCI, electrical outlet. Do Not use an
extension cord or an adapter plug.
= If possible, place the refrigerator out of
direct sunlight and away from the range,
dishwasher, or other heat sources.
The refrigerator must be installed on a floor
that is level and strong enough to support
a fully loaded refrigerator.
Consider water supply availability for
models equipped with an automatic ice
maker.
Do Not install the refrigerator where the
temperature will drop below 55°F (13°C) or
rise above 110°F (43°C). The compressor
will not be able to maintain proper
temperatures inside the refrigerator.
Do Not block the toe grille on the lower front
of your refrigerator. Sufficient air circulation
is essential for the proper operation of your
refrigerator. ....
Installation
Allow the following clearances for ease
of installation, proper air circulation, and
plumbing and electrical connections:
Sides & Top 3/8inch (9.5 mm)
Back 1 inch (25.4 mm)
:If your refrigerator is placed with the door
hinge side against a wall, you may have to
allow additional space so the door can be
opened wider.
Door opening
The refrigerator doors are designed to shut
by themselves within a 20 degree opening,
ii
Your refrigerator should be positioned to allow
easy access to a counter when removing
food. For best use of refrigerator drawers and
freezer baskets, the refrigerator should be in a
position where both can be fully opened.

Leveling Freezer Drawer (if
necessary)
1 Check gasket seal around top, bottom,
and sides of freezer drawer.
2 If gasket is not sealed, open drawer and
slightly loosen four (4) drawer screws
(two (2) on each side) to allow drawer to
rotate.
3 Close drawer and recheck the seal on the
gasket (A). Open the drawer grabbing by
the sides in the center (B). Be careful not
to rotate the drawer.
Remove Remove
hex
head head
drawer drawer
screw screw
To level the cabinet using the front
rollers (select models):
1 Slightly open freezer drawer. Lift the
toe grille and gently pull forward (see
illustration).
2 You can raise or lower each door. Use
a 3/s inch socket wrench to turn the
adjustment screws (1 per side).
Toe Grille Must
'Remove
Hex Hex
Head ....... Head
Drawer Drawer
Screw Screw
4 Tighten four (4) drawer screws.
5 Recheck gasket seal.
Push
Against
Freezer
Level Refrigerator &Adjust
Doors (if necessary)
Guidelines for final positioning of your
refrigerator:
= All four corners of the cabinet must rest
firmly on the floor.
The sides should tilt 1/4inch (6 mm) from
front to back (to ensure that doors close
and seal properly).
Doors should align with each other and be
level.
Host of these ¢ond_ons can be met by raising
or lowering the adjustable front rollers.
To raise: turn adjustment screw
clockwise.
To lower: turn adjustment screw
counterclockwise.
3Ensure both doors are bind-free with their
seals touching the cabinet on all four sides
and that cabinet is stable.
4 After unit is leveled, lower anti-tip leg until
it contacts the floor.
\JRaise
5 Install the toe grille by fitting into place.

To adjust the door stop:
Door stopisadjustablebetween 85 to 145
degrees.
5Retighten screw.
View shown is looking up at the bottom of
the refrigerator door.
Hi ,Door
_c_ew
Adjustable Door Stop
1 Open door to provide access to screw.
2 Loosen screw.
3Adjust door to desired location
Rotate
Door to Desired
Location
Adjusting Door
4 Rotate door stop until it makes contact
with the lower hinge.
Re-tighten
Screw0
Retighten Screw
6Ensure door stops in desired location
before resuming normal use.
To level the doors using the adjustable
lower hinge (select models):
1 Remove all food items from door bins on
door being adjusted.
2 Open doors to 90 degrees.
3 Loosen or remove screw,
Bottom of Door
Loosen/Remove Screw (where applicable)
Adjustable hinge should only be used after
doors have been leveled with rollers.

Lift the door while adjusting the washer.
To raise the door, rotate washer clockwise
(when viewed from the bottom). To lower
door, rotate washer counterclockwise
(when viewed from the bottom).
Hin
Washer
Raising/Lowering Door
Re-tighten the screw (where applicable),
ensuring it is between the spokes of the
washer. Screw will not be tight, just insert
until it is flush with the hinge.
Retighten Screw
@
Screw (where applicable)
To adjust the flipper aullion:
ILoosen the screw located on the flipper
mullion hinge. I!r
Mullion
Adjusting Flipper MuBien Screw
2 Adjust flipper mullion height. For proper
connection with the flipper mullion guide,
there should be a separation about the
thickness of a coin (0.060 inches, or
1.5 mm) between the guide and flipper
mullion.
ckness
of a Coin
Adjusting Flipper Mullion Height
3Retighten screw.
If after adjusting doors higher the door
makes a popping/clicking sound, remove
screw and replace with the longer one
supplied in the handle package (select
models).

Getting through narrow spaces
If your refrigerator will not fit through an
entrance area, you can remove the doors.
Check first by measuring the entrance.
To prepare for removing the doors:
1 Make sure the electrical power cord is
unplugged from the wall outlet.
2 Open the freezer drawer and remove the
toe grille (see "Installation" section).
3Remove any food from the door shelves
and close the doors.
To remove the top hinge covers:
1 Remove the two (2) screws from each
cover over the top door hinges.
2 Lift inside edge of hinge cover and tilt
back.
DO NOT remove the ground screw from
hinge.
To remove the refrigerator doors:
1 Trace lightly around the door's top hinges
with a pencil. This makes reinstallation
easier.
Front
cover screw e ..... Rear
\ A _-- cover
Top hinge _J _ screw
cover
Hinge "h-_-_/- Ground
screws _--
Multi-wire
hinge
Disconnect the harness by grasping both
sides of the connector firmly, depress the
latch, and pull apart. Remove the two (2)
screws from the top hinge. Lift the door
off of the bottom hinge and set it aside.
Leave
hin J
door
Rear Front
Cover ---_ Cover Screw
Screw-_/l__ /Top Hinge
I
To_ Hinge
u,_'_ Screw _Screws
Two Wire
'II Leave
With
_t ooor
_!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!¸9¸¸i¸ii¸ilii

Youwillbepullingapproximatelythree(3)
feetofwatertubefromthebackofthe
refrigerator,
4 Unscrewthethree(3)lowerhingescrews
andhingeifnecessary.
Toreinstalltherightdoor,reversetheabove
steps. LowerHinge Removal
Once both doors are in place, ensure they are
aligned with each other and level (Please see
the "Installation" section for more details), and
replace the top hinge cover.
Besure doors are set aside in a secure position
where they cannot fall and cause personal
injury, or damage to the doors or handles.
Removing Freezer Drawer
1 Open freezer drawer.
2 Removedrawer screws on right andleft
sides(two (2) screws on each side).
Remove Remove
hex hex
head head
drawe drawer
screw
i
_Remove
Hex Hex
Head Head
arawel Drawer
Screw Screw
]Installing Freezer Drawer
1 With lower slides pulled out, hang drawer
onto slide brackets ensuring pins on each
side are fully inserted into slots on each side.
Assembly Fully Extend
Drawer Slides
2 Reinstall four (4) drawer screws (two (2) per
side), tighten down, and close drawer (C).
Install
Screws j
(2) Each \
Side
o
3Check gasket seal around top, bottom,
and sides of freezer drawer.
4 If gasket is not sealed, open drawer and
slightly loosen four (4) drawer screws (two
(2) on each side) to allow drawer to rotate.
5Close drawer and recheck the seal on the
gasket (A). Open the drawer grabbing by
the sides in the center (B). Be careful not
to rotate the drawer.
Push L= /==
Against
Freezer
Drawer is heavy. Use caution when lifting. 6Tighten four (4) drawer screws.
7 Recheck gasket seal.
3 Lift drawer up and out to remove. 8 Install the toe grille by fitting into place.

Door Handle Mounting Instructions for Frigidaire Gallery ®
1 Remove handles from carton and any other protective packaging.
3
4
5
6
7
Position fresh food handle end over upper and lower pre-installed shoulder bolts (A)
that are fastened into door, ensuring the holes for the set screws are facing towards the
opposite door.
While holding handle firmly against door, fasten upper and lower Allen set screws (B) with
supplied Allen wrench.
Repeat steps 2 and 3 to install opposite handle. Ensure the holes for the set screws are facing
towards the first door.
Position freezer handle end over left and right pre-installed handle mounts that are fastened
to the door, ensuring the holes for the set screws are facing down.
While holding handle firmly against door, loosely tighten far right Allen set screw (B) with supplied
Allenwrench until there is no gap between handle and door.
Still holding the handle firmly to the door, firmly tighten far left Allen set screw (B) with supplied Allen
wrench.
8Return to the far right Allen set screw (B) and firmly tighten with supplied Allen wrench.
Mounting Refrigerator Handles
All set screws should be
tightened so the screw is below
the surface of the handle. The
handles should be drawn tight
to freezer and refrigerator doors
with no gaps. Opening the
opposite door while tightening
the Allen screw makes
installation easier.
The door handle may loosen
over time or if it was installed
improperly. If this happens,
tighten the set screws on the
handles. !ii
Mounting Freezer Handle
Wear gloves and safety goggles.
Use extreme CAUTION when
installing these handles.

Door Handle Mounting Instructions for Frigidaire Professional ®
1 Remove handles from carton and any other protective packaging.
2 Position fresh food handle end over upper and lower pre-installed shoulder bolts (A)
that are fastened into door, ensuring the holes for the set screws are facing towards the
opposite door.
3While holding handle firmly against door, fasten upper and lower Allen set screws (B) with
supplied Allen wrench.
4 Repeat steps 2 and 3 to install opposite handle. Ensure the holes for the set screws are facing
towards the first door.
5 Position freezer handle end over left and right pre-installed handle mounts that are fastened
to the door, ensuring the holes for the set screws are facing down.
6While holding handle firmly against door, loosely tighten far right Allen set screw (B) with supplied
Allenwrench until there is no gap between handle and door.
7 Still holding the handle firmly to the door, firmly tighten far left Allen set screw (B) with supplied Allen
wrench.
8Retum to the far right Allen set screw (B) and firmly tighten with supplied Allen wrench.
9 Firmly tighten the insideAllen set screws.
Mounting Refrigerator Handles
All set screws should be
tightened so the screw is below
the surface of the handle. The
handles should be drawn tight
to freezer and refrigerator
doors with no gaps. Opening
the opposite door while
tightening the Allen screw makes
installation easier.
The door handle may loosen
over time or if it was installed
improperly. If this happens,
tighten the set screws on the
handles.
ii
Mounting Freezer Handle
Wear gloves and safety goggles.
Use extreme CAUTION when
installing these handles.

Toavoid electric shock, which can cause
death or severe personal injury, disconnect
the refrigerator from electrical power before
connecting a water supply line to the
refrigerator,
• A shutoff valve to connect the water supply
line to your household water system. DO
NOT use a self-piercing type shutoff valve.
• Do not reuse compression fitting or use
thread seal tape.
• A compression nut and ferrule (sleeve) for
connecting a copper water supply line to
the ice maker inlet valve.
To Avoid Property Damage:
Copper or Stainless Steel braided tubing
is recommended for the water supply
line. Water supply tubing made of 1/4
inch plastic is not recommended to be
used. Plastic tubing greatly increases
the potential for water leaks, and the
manufacturer will not be responsible for
any damage if plastic tubing is used for
the supply line.
DO NOT install water supply tubing in
areas where temperatures fall below
freezing.
Check with your local building authority
for recommendations on water lines and
associated materials prior to installing your
new refrigerator. Depending on your local/
state building codes, Frigidaire recommends
for homes with existing valves its Smart
Choice® water line kit 5305513409 (with
a 6 ft. Stainless Steel Water Line) and for
homes without an existing valve, Frigidaire
recommends its Smart Choice® water line
kit 5305510264 (with a 20 ft. Copper Water
Line with self-tapping saddle valve). Please
refer to www.frigidaire.com/store for more
information.
•Chemicals from a malfunctioning softener
can damage the ice maker. If the ice
maker is connected to soft water, ensure
that the softener is maintained and
..... working properly: .................................................................................................
Ensure that your water supply line
connections comply with all local plumbing
codes.
Before Installing The Water Supply Line,
You Will Need:
• Basic Tools: adjustable wrench, fiat-blade
screwdriver, and PhillipsTM screwdriver
• Access to a household cold water line with
water pressure between 30 and 100 psi.
• A water supply line made of 1/4inch (6
mm) OD, copper or stainless steel tubing.
To determine the length of tubing needed,
measure the distance from the ice maker
inlet valve at the back of the refrigerator
to your cold water pipe. Then add
approximately 7 feet (2.1 meters), so the
refrigerator can be moved out for cleaning
(as shown).

To Connect Water Supply Line To Ice Maker
Inlet Valve
1. Disconnect refrigerator from electric power
source.
2. Place end of water supply line into sink or
bucket. Turn ON water supply and flush
supply line until water is clear. Turn OFF
water supply at shutoff valve.
3. Remove plastic cap from water valve inlet
and discard cap.
4. If you use copper tubing - Slide brass
compression nut, then ferrule (sleeve)
onto water supply line. Push water
supply line into water valve inlet as far
as it will go (1/4inch/6 mm). Slide ferrule
(sleeve) into valve inlet and finger tighten
compression nut onto valve. Tighten
another half turn with a wrench; DO NOT
overtighten. See Figure 1.
If you use stainless steel tubing - The nut
and ferrule are already assembled on the
tubing. Slide compression nut onto valve
inlet and finger tighten compression nut
onto valve. Tighten another half turn with
a wrench; DO NOT overtighten. See Figure
2.
5. With steel clamp and screw, secure water
supply line (copper tubing only) to rear
panel of refrigerator as shown.
6. Coil excess water supply line (copper
1
tubing only), about 2/2 turns, behind
refrigerator as shown and arrange coils so
they do not vibrate or wear against any
other surface.
7. Turn ON water supply at shutoff valve and
tighten any connections that leak.
8. Reconnect refrigerator to electrical power
source.
Plastic water _ Steel
Tubing to ice _C!amp
Maker Fill Brass
Compression
Nut ;)
water line
Bracket
inlet
......................... Copper waterline
from household
water supply
include enough tubing in !oop
jerator out
for cleaning:)
Figure I
Plastic Water Tubing
to Ice Maker _ _ Steel
F Tube /f_1_ Clamp
i i
_ _] _-Stainless
_J:_:_i Steel
__ waterline
__ "Water Valve
/_/ )__ Bracket
Cb
Wate Va,vo
el water line
J from household water supply
Figure 2

IQ-Touch T"
A red indicatorlightwillbe illuminatedabove most activefeatures.
Touch the icon to activate the options below.
quick ice Increases the production of ice
water filter Pressand holdforthree(3)secondsto resetafter
filter change.
C/! = Touch to toggle display from Fahrenheit to Celsius.
default settings Resets all refrigerator settings such as temp, temp
display and tones to their factory default settings.
Power on-off Pressand hold for three (3) seconds to turn off the
cooling system to cleanthe refrigerator. It alsoturns off
the ice maker. The temperature displays will read OFF.
Energy Saver Keepthisswitchseton energy saver (lighton)for
lowestenergyusage.Ifmoistureappearson the
cabinetbetweenthedoors,pressingthisbuttonwill
turnthelightoffand enablean electricheaterused to
reducemoistureon thecabinetbetweenthedoors.
Pressing the system on-off icon does not turn off power to your
refrigerator. You must unplug the power cord from the wall outlet.
Setting cooling temperatures
Pressthe"A"or"v"indicatortoadjustthetemperaturetothedesiredsetting.
The temperaturedisplaywillbeginto blinkwiththe firsttouch.The
displaywilltimeout after10 seconds and returnto the basicdisplay.
High Temp
Power Fail
If the door has been left open for an extended period
of time, an alarm will sound and the door ajar indicator
will display on the bottom display of the control panel.
The alarm is turned off by closing the door. The mute
sounds key will blink to prompt the reset of any active
alarms. Press this key to reset any system alarms.
In the event of a high temperature condition, the tem-
perature display will blink and display "HI': After 20 min-
utes, the alarm will sound and the high temp indicator
will be red on the bottom of the control panel. The mute
sounds icon will illuminate until pressed, acknowledging
the alarm, at which time the highest temperature reached
will be displayed and the refrigerator will resume normal
operation. In case the high temp alarm is not acknowl-
edged at the first alarm sound time out, when the door is
first opened, the alarm sound will be repeated.
In the event of a power failure, the power fail alert will
be displayed and the temperature display will blink until
the mute sounds icon is pressed, acknowledging the
alarm. Other modes may be turned off until the alarm is
acknowledged. The power fail alert is turned off and
the refrigerator will resume normal operation. The high
ternp alarm may also be illuminated until a safe
operating range temperature has been reached.

IQ-Touch TM"Sabbath Hode"
The Sabbath Mode is a feature that disables portions of the refrigerator and its controls in
accordance with observance of the weekly Sabbath and religious holidays within the Orthodox
Jewish community.
Sabbath Mode is turned ON and OFF by pressing and holding both the freezer "v" and
refrigerator"A" indicators for five (5) seconds. The display shows "Sb" while in Sabbath mode.
In the Sabbath Mode, the High Temp alarm is active for health reasons. If a high temperature
alarm is activated during this time, for example due to a door left ajar, the alarm
will sound intermittently for about 10 minutes. The alarm will then silence on its
own and a red high temperature icon will display. The high temp icon will continue
to display, even if the door is closed, until the Sabbath mode is exited and the icon
reset. The refrigerator will function normally once the door is closed, without any
violation of the Sabbath/Holidays.
For further assistance, guidelines for proper usage and a complete list of models with the
Sabbath feature, please visit the web at http:\\www.star-k,org.
While in Sabbath Mode, neither the lights nor the control panel will work until Sabbath Mode
isdeactivated.
Refrigerator stays in Sabbath Mode after power failure recovery. It must be deactivated with
thebuttonsonthecontrolpaoel.

Ice maker operation & care
After the refrigerator is installed properly, the
ice maker can produce ice within 24 hours. It
can completely fill an ice bin in about three (3)
days.
When using the ice maker for the first time and
in order for the ice maker to work properly, it is
necessary to clear air from water filter tubing.
Once ice maker begins making ice, allow the
bucket to fill completely, then discard the first
TWO (2) FULL buckets of ice. It will take at
least two (2) days to completely fill the bucket
on regular ice making mode or 1 1/2days on
fast ice mode.
The ice maker produces approximately four
(4) pounds of ice every 24 hours depending on
usage conditions.
The following sounds are normal when the
ice maker is operating:
Motor running
Ice dropping into ice bin
Water valve opening or closing
Running water
Ice cubes stored too long may develop an odd
flavor. Empty the ice bin as explained below.
Quick Ice Function
Your refrigerator is equipped with a Quick Ice
Function, that increases ice production. This
function terminates automatically.
Cleaning the ice maker
: : ; : ; ;If the water supply to your refrigerator is
Your ice maker is turnea on at the factory
• . . softened, be sure the softener is properly
so _tcan WOrKas soon as you install your
. maintained. Chemicals from a water softener
reTrigerator If you cannot connect a water ....
• ' . . . can aamageme ice maker.
suppy, iftthe ice makerswlre slgna arm ...............................................
to turn it off. Otherwise, the ice maker's Clean the ice maker and ice bin at regular
intervals, especially prior to vacation or moving.
fill valve may make a loud chattering noise
when it attempts to operate without water.
Turning the ice maker on and off
Ice production is controlled by lifting/lowering
the ice maker's wire signal arm. To gain
access to the ice maker, pull the freezer drawer
out. Lift the wire signal arm to turn the ice
maker OFF and lower the wire signal arm to
turn it ON.
Sgna Arm
Ice maker tips
If your refrigerator is not connected to a water
supply or the water supply isturned off, turn
offthe ice maker by lifting wire signal arm.
1
2
3
Turn off the ice maker.
Remove the ice bin.
Empty and carefully clean the ice bin
with mild detergent. Do not use harsh or
abrasive cleaners. Rinse with clean water.
4 Allow the ice bin to dry completely before
replacing in the freezer.
5 Replace the ice bin. Turn the ice maker on.
Remove and empty the ice bin if:
An extended power failure (one hour or
longer) causes ice cubes in the ice bin to
melt and freeze together.
Remove the ice bin and shake to loosen the
cubes or clean as explained above.
NEVER use an ice pick or similar sharp
instrument to break up the ice. This
could damage the ice bin and dispenser
mechanism.
To loosen stuck ice, use warm water.
Before replacing the ice bin, make sure it is
completely dry.

Toavoidpersonalinju_/orproperlydamage,
handletemperedglassshelvescarefully.Shelves
maybreaksuddenlyifnicked,scratched,or
exposedtosuddentemperaturechange.Allow
meglassshelvestostabilizetoroomtemperature
not .............................
Crispers
Crisper drawers are designed for storing fruits,
vegetables, and other fresh produce.
Features may vary according t0 model.
Your refrigerator includes SpillSafeTM glass
shelves that are designed to catch and hold
accidental spills.
You can easily adjust shelf positions in the
fresh food compartments to suit your needs.
The shelves have mounting brackets that
attach to slotted supports at the rear of each
compartment.
To change the position of a shelf:
i Remove all food from the shelf.
2 Lift the front edge up and pull the shelf out.
3 Replace by inserting the mounting bracket
hooks into the desired support slots.
4 Lower the shelf and lock into position.
Shelf features
Full SpillSafe TM Shelf
TM
Half SpilISafe Shelf
Drawers
Yourrefrigerator includesa variety of storage
drawers. These drawers are located in fixed positions
at the bottom of t_e fresh food compartment.
Opening Crisper Drawer
Crisper humidity control
Crisper drawers include a sliding control for
adjusting the humidity inside the crisper, Leafy
vegetables keep best when stored with the
Humidity Control set on Higher Humidity. Fresh
fruits keep best when stored with the Humidity
Control set on Lower Humidity,
Vegetables Fruits
hi ............. Io
Higher Lower
Humidity Humidity
Adjusting CrisperHumidity
To remove the Crisper Drawer for cleaning:
1 Pullthe drawer out until it stops.
2 Liftthe front slightlyand removethe drawer.
Removing Crisper Drawer

Dell drawer
Ideal for storage of deli meats and cheese.
Doors
Storage bins
The doors to your fresh food compartment use
a system of modular storage bins. All of these
bins are removable for easy cleaning. Some of
them have fixed positions, while others can be
adjusted to your needs.
Door bins are ideal for storing jars, bottles,
cans, and large drink containers. They also
enable quick selection of frequently used
items.
To change the position of an adjustable
door bin:
1 Remove all food from the door bin.
2 Grip the bin firmly with both hands and lift
it upward.
3 Remove the bin.
4 Place the bin just above desired position.
5 Lower the bin onto supports until locked in
place.
Adjustable Door Bin
6 Place bin liner into bin.
]
€
Accessories (varies by model)
Dairy compartment
Use the dairy compartment, at the top of the
fresh food compartment door, for short-term
storage of cheese, spreads, or butter. The dairy
compartment is designed to be warmer than
the open area and includes a lift-up cover and
a dairy divider (select models).
Dairy Compartment
Freezer Features (varies by model)
_ilizer Bar
Basket
RetainerClips
Two Freezer Baskets

To Remove Upper Basket
1 Remove all items from basket.
2 Remove basket by pulling baskets out to
their full extension and lift out.
Removing Upper Basket
To reinstall upper basket, position basket onto the
retainer clips making sure the front of the basket
rests in the retainer clips on the stabilizer bar.
If basket is not resting on stabilizer bar retainer
clips, the drawer will not close properly.
To Remove Lower Basket
1 Remove all items from basket.
2 Remove the basket by tilting it forward
and lifting it from the retainer clips.
Removing Lower Basket
Middle Basket
Divider
Retainers
Stabil
Bar Hiddle Basket Divider
Lift up on the rear of the lower divider and pull out.
Lower Basket
Lower Basket Divider & Spill Guard Tray
To reposition the pivoting divider (some models),
lift up and slide to desired location.The pivoting
divider is not designed to be removed.
Spill Guard Lower Basket
Tray ..................... Divider
To reinstall lower basket, insert basket into retainer dips.
Dividers Removal
Lift up on me front of the middle divider and pull out.
Lower Basket Pivoting Divider (some models)
_!!!i_!_!120i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i;i;i;i;i;i;i;i;i;i;i;i;i;i;i;i;i;i;i;i;i;i;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_