Frigidaire GLTF2070DS0 User manual

Installation
Instructions
Full Size Tumble Action Washers
Before beginning installation, carefully read these instructions. This will simplify the
installationandensurethe washerisinstalledcorrectlyandsafely.Leavetheseinstructions
near the washer after installation for future reference.
NOTE:The electrical service to the washer must conform with local codes and ordinances
and the latest edition of the National Electrical Code, ANSI/NFPA 70.
Contents
SUBJECT PAGE
Pre-InstallationRequirements 2
ElectricalRequirements 2
GroundingRequirements 2
WaterSupplyRequirements 2
DrainRequirements 2
Rough-InDimensions 3
LocationOfYourWasher 4
Unpacking 4
Installation 5
ReplacementParts 5
Printed in U.S.A. P/N134305600(0310)
Foryour safety theinformation in
this manual must be followed to minimize the
risk of fire or explosion or to prevent property
damage, personal injury or loss of life.
- Do not store or use gasoline or other
flammable vapors and liquid in the vicinity of
this or any other appliance.
- WHATTO DO IFYOU SMELL GAS
·Do not try to light any appliance.
·Do not touch any electrical switch; do not
use any phone in your building.
·Clear the room, building or area of all
occupants.
·Immediately call your gas supplier from a
neighbor’s phone. Follow the gas suppliers
instructions.
·If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.

2
PRE-INSTALLATION REQUIREMENTS
Tools Required for Installation:
1. 1/4 in. nut driver
2. 3/8 in. socket with ratchet.
3. 3/8 in. open end wrench.
4. 7/16 in. socket with ratchet.
5. 9/16 in. open end wrench.
6. Channel-lock adjustable pliers.
7. Carpenter’s level.
ELECTRICAL REQUIREMENTS
CIRCUIT -Individual,properly polarizedand grounded
15 amp. branch circuit fused with 15 amp. time delay
fuse or circuit breaker.
POWER SUPPLY - 2wire, with ground, 120 volt,single
phase,60Hz,AlternatingCurrent.NOTE:Theuseofthis
washerwithpowercreatedbygaspoweredgenerators,solar
poweredgenerators,windpoweredgeneratorsoranyother
generator other than the local utility company is not
recommended.
OUTLET RECEPTACLE -Properlygrounded3-prong
receptacle to be located so the power supply cord is
accessiblewhenthewasher is in an installed position.
NOTE:GFI (GroundFaultInterrupter)receptacleis not
required.
GROUNDING REQUIREMENTS
Improperconnectionoftheequipment
grounding conductor can result in a risk of electrical
shock. Check with a licensed electrician if you are in
doubtastowhethertheapplianceisproperlygrounded.
1. The washer MUST be grounded. In the event of
malfunctionor breakdown, groundingwill reduce
the risk of electrical shock by a path of least
resistance for electrical current.
2. Sinceyourwasherisequippedwithapower supply
cord having an equipment-grounding conductor
anda grounding plug, theplugMUST be plugged
intoanappropriate,copperwiredreceptaclethatis
properlyinstalledandgroundedinaccordancewithall
localcodesandordinancesorintheabsenceoflocal
codes,withtheNationalElectricalCodes,ANSI/NFPA
70(latestedition).Ifindoubt,callalicensedelectrician.
DO NOT cutoff or alter the groundingprong on the
power supply cord. In situations where a two-slot
receptacleispresent,itistheowner’sresponsibilityto
havealicensedelectricianreplaceitwithaproperly
groundedthreepronggroundingtypereceptacle.
WATER SUPPLY REQUIREMENTS
Hot and cold water faucets MUST be installed within
42 inches (107 cm) of your washer’s water inlet. The
faucets MUST be 3/4 inch (1.9 cm) garden hose type
soinlet hosescanbeconnected.Waterpressure MUST
bebetween30and120poundspersquareinch(maximum
unbalance pressure, hot vs. cold, 10 psi.)Your water
departmentcanadviseyouofyourwaterpressure.Thehot
watertemperatureshouldbeabout140degreesF(60degrees
C).
DRAIN REQUIREMENTS
1. Drain capable of eliminating 17 gals (64.3 L) per
minute.
2. A standpipe diameter of 1-1/4 in. (3.18 cm)
minimum.
3. The standpipe height above the floor should be:
Minimum height: 24 in. (61 cm)
Maximum height: 96 in. (244 cm)
NOTE:
Drainhose attached tothe washer canreacha 58
in. (147 cm) high standpipe. For higher standpipe
usehoseP/N134049201,availablefromanauthorized
parts distributor. Ifdrain is less than 24in. (61 cm),
install a siphon break kit, available at your local
hardwarestore.
Max.

3
ROUGH-IN DIMENSIONS
24
(61)
17 1/2
( 44.5 )
(61)
171/2
(44.5)
21/2
(6.4)
21/2
(6.4)
351/4
(89.5)
351/4
(89.5)

4
LOCATION OF YOUR WASHER
DO NOT INSTALL YOUR WASHER:
1. In an area exposed to dripping water or outside
weather conditions. The ambient temperature
shouldnever be below60 ° F(15.6 °C) for proper
washer(detergentbreakdown)operation.
2. In an area where it will come in contact with
curtains or drapes.
3. In an area (garageor garage-type building)where
gasoline of other flammables are kept or stored
(including automobiles).
4. On carpet. Floor MUST be solid with a maximum
slope of 1/2 in. per foot (1.27 cm per 30.5 cm).To
ensure vibration or movement does not occur,
reinforcement of the floor may be necessary.
IMPORTANT
MINIMUMINSTALLATION CLEARANCES
When installed in alcove or closet:
Sides, Rear = 0 in. (0 cm)
Top = 0 in. (0 cm) Front Console Model
Top = 15 in. (38.1 cm) Rear Console Model
When installed in closet: Front = 1 in. (2.54 cm)
Closet door ventilation required: 2 louvered openings
each60in2(387cm2),3in.(7.6cm) fromtopand bottom
ofdoor.
UNPACKING
1. Cuttheshippingcarton along thedotted line along
the base of the unit.
2. While in the carton carefully lay the washer on its
back side.
3. Remove the styrofoam base.
4. Carefullyreturnthewashertoanuprightpositionand
removethecarton.
5. Carefullymovethewashertowithin4feet(122cm)of
thefinallocation.
6. Remove the following from the back side of the
washer: 4 bolts,
4 yellow plastic spacers,
3 metal "P" clamps.
7. Remove the service panel from the front of the
washer.
8. Remove the 4 nutsand 6 large washersthat attach
the 2 yellow shipping braces to the drum and the
base. Lift up on the drum and remove the braces
(a yellow ribbon surrounds the items to be
removed).These bracesmustberemovedto allow
the power supply cord to be released from the
shipping ring.
9. Remove the large styrofoam block located under
the drum. Lift up on the drum, tilt the base of the
foam block inwards toward the rear of the washer
until free, then pull it out.
10. Remove and discard the yellow ribbon and label
from the front of the washer.
11. From the rear of the washer, carefully pull out the
power supply cord through the hole in the
backsheet.
12. Replace the service panel and screws.
NOTE: Ifthe washer is tobe transportedata later
date,the shipping supporthardware must
be reinstalled to prevent shipping
damage. Retain the hardware in the
plastic bag provided.
SPACER
"P" CLAMP
BOLT

5
Cable
Tie
REPLACEMENTPARTS
If replacements parts are needed for your washer,
contact the source where you purchased your
washer, call 1-800-944-9044, or visit our website,
www.frigidaire.com, for the Frigidaire Company
Authorized Parts Distributor nearest you.
Destroy the carton and plastic bags
afterthewasheris unpacked.Childrenmight use them
for play. Cartons covered with rugs, bedspreads, or
plasticsheets canbecomeairtightchambers causing
suffocation.Place all materialsina garbage container
or make materials inaccessible to children.
The instructions in this manual and all
otherliteratureincludedwiththiswasherarenotmeantto
covereverypossibleconditionandsituationthatmayoccur.
Goodsafe practiceandcautionMUST beappliedwhen
installing,operating and maintaininganyappliance.
Maximum benefits and enjoyment are achieved
when all the Safety and Operating instructions are
understood and practiced as a routine with your
launderingtasks.
Cable Tie
Cable
Tie
Plug the power cord into a grounded outlet.
NOTE: Check to ensure the power is off at a circuit
breaker/fuse box before plugging the power
cord into an outlet.
Turn on the power at a circuit breaker/fuse box.
10. Read the Operating Instructions and Owner’s Guide
provided with the washer. They contain valuable
and helpful information that will save you time and
money.
11. Runthewasherthroughacompletecycle. Checkforwater
leaksandproperoperation.
12. If your washer does not operate, please review the
“Avoid Service Checklist” in your Owner’s Guide before
calling for service.
13. Place these instructions in a location near the washer
for future reference.
NOTE: Awiringdiagramandtechnicaldatasheetarelocatedin
anenvelopeattachedtothelefthandsidepanelonthe
inside of the washer.
INSTALLATION
1. Run some water from the hot
and cold faucets to flush the
water lines and remove
particles that might clog up the
water valve screens.
2. Remove the inlet hoses and
rubber washers from the
plastic bag and install the
rubber washers in each end
of the inlet hoses.
3. Carefullyconnecttheinlet hose
(90°elbow end) marked "HOT"
to the outside "H" outlet of the
watervalve. Tightenbyhand,then
tighten another 2/3 turn with
pliers.Carefullyconnecttheother
inlethose (90° elbow end)tothe
inside"C"outletofthewatervalve.
Tighten by hand, then tighten
another2/3 turn with pliers. Do
not crossthread or over-
tightentheseconnections.
4. Connecttheinlet hose endstotheHOTandCOLDwater
faucetstightlybyhand,thentighten another 2/3turnwith
pliers.Turnthewateronandcheck forleaks.
NOTE: Useonlynewhoses.
5. Carefullymovethewashertoitsfinallocation.
NOTE: Do not use the dispenser drawer or door to lift
washer.
6. Withthewasherinits final position, placealevelon top of
thewasher,norockingofthewashershouldexist.Adjustthe
frontlevelinglegsupordowntoensurethewasherisresting
solid.Rearleg adjustment isaccessiblethrough the front
servicepanel. Turnthelocknutsoneachleguptowardsthe
baseofthewasherandsnugwithawrench.
NOTE: Keepthelegextensionat a minimum toprevent
excessivevibration.Thefarther out thelegsare
extendedthemorethewasherwillvibrate.
7. FormaUshape ontheendofthedrainhosewiththehose
pointedtowardthedrain.Placeinalaundrytuborstandpipe
and secure with the cable tie provided in the enclosure
package.
NOTE: Ifthedrainhoseisplaced in a standpipewithout
formingaUshape,asiphoningactioncouldoccur.
Theremustbeanairgaparoundthedrainhose.A
snughosefitcanalsocauseasiphoningaction.
8.
9.