Frontier MSS507F User manual

Model No.MSS507F
IMPORTANT:
Please read this manual before using this
Miter Saw Stand and save it for reference.
INSTRUCTION
MANUAL
MITER SAW STAND
WITH EXTENSION SUPPORTS

TABLE OF CONTENTS
NOTE: If any parts are missing or damaged, or if you have any
questions, please call our toll-free helpline at 1-800-689-9928.
TM
TABLE OF CONTENTS
Quick start guide 4-5
Specifications 6
Safety guidelines 7
Key parts diagram 8
Operating instructions 9
Warranty 10
SAVE THESE INSTRUCTIONS.
This manual contains important safety and operating instructions.
Read all instructions and follow them with use of this product.
3

Model No.MSS507F ⼁Contact us: Customerser[email protected]
QUICK START GUIDE
1
2
3
4
TABLE OF CONTENTS
QUICK START GUIDE
WARNING
TM
4
5
67
·Before operating this tool, carefully read this Instruction Manual and all of the labels
affixed to the tool. Failure to follow all warnings and instructions may result in electric
shock, fire and/or serious injury.
·Save all warnings and instructions for future reference.
NOTE: If any parts are missing or damaged, or if you have any
questions, please call our toll-free helpline at 1-800-689-9928.
5

39 3/4 (1.01m )''
32 1/4
( 82 cm)
''
SPECIFICATIONS
SPECIFICATIONS
Max
300 lb
Maximum load 300 lb (136.1 kg)
Length of saw stand without table extension 39 3/4 (1.01m )''
Length of saw stand with table extension
Maximum height 32 1/4 ( 8 2 cm) from ground to tabletop
''
WARNING
·The maximum load（power tool+ workpiece）of the saw stand is 300 lb(136.1 kg). Do not
overload the saw stand and do not use it as a ladder or scaffolding.
6
（136.1 kg）
Weight 25 lb (11.3 kg)
7 ( 2.4m )
1 /2
7 (2.4m )
1 /2
SAFETY GUIDELINES
SAFETY GUIDELINES
en
General Safety Rules
Safety Warnings for Saw Stands
7
Assemble the saw stand in the proper man-
ner before mounting the power tool.
Proper assembly is important to prevent
the risk of a collapse of the saw stand.
Attach the power tool securely to the
saw stand before using it. Slipping off
of the power tool on the saw stand can
lead to loss of control.
Pull the plug from the mains receptacle
and/or remove the battery from the
power tool before making adjustments on
the tool or changing tool accessories.
Unintentional switching on of the power
tool is the cause of many accidents.
Read all warning notes and in -
structions enclosed with the
saw stand and the power tool to be mounted.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or
serious injury.
Place the saw stand on a firm, level and
horizontal surface. If the saw stand can
slip off or wobbles, the power tool or the
workpiece cannot be uniformly and
securely guided.
Do not overload the saw stand and do
not use it as a ladder or scaffolding.
Overloading or standing on the saw
stand can lead to the upward shifting of
the centre of gravity of the stand and its
tipping over.
When working or transporting, take
care that all bolts and connecting
elements are firmly tightened. The
Mounting Brackets for the power tool
must always be firmly locked. Loose
connections can lead to insta-bility and
inexact sawing.
Mount and dismount the power tool only when it
is in the transport position (for instructions on
the transport position, also see the operating
instructions of the respective power tool).
Otherwise, the power tool can have such an
unfavourable centre of gravity that it cannot be
held securely.
When the power tool is mounted to the Mounting
Brackets operate it exclusively on the saw
stand. Without the saw stand, the power tool
with the Mounting Brackets on does not stand
securely and can tip over.
Ensure that long and heavy workpieces do not
affect the equilibrium of the saw stand. Long
and/or heavy workpieces must be supported at
the free end.
Keep your fingers clear of the hinge points
while putting the saw stand together or pulling
it apart. Otherwise, your fingers may get
crushed or contused.
Model No.MSS507F ⼁Contact us: Customerser[email protected]
''
''

KEY PARTS DIAGRAM
KEY PARTS DIAGRAM
Carriage Bolt M8×40 ×4
A
B
C
D
E
1.Table×1
2.Workpiece Supports×2 3.Mounting Brackets ×2
4.Locking Knobs×2
6Nut Locking Plate ×4
Flat Washer×4
Spring Washer×4
Nut×4
5.Locking Knobs with Bolt×2
8
OPERATING INSTRUCTIONS
Assembling the Saw Stand
Setting up the Saw Stand (see Fig. 1-2)
Preparing the Saw Stand
Operation
·Do not overload the Saw Stand. Always observe the maximum load of the Saw Stand and the
two table extensions.
·Always hold the workpiece firmly, especially the longer and heavier section. After cutting
through the workpiece, the centre of gravity may become dislocated in such an unfavourable
manner that the saw stand tips over.
·If possible, always place the workpiece on one or both workpiece supports.
WARNING
9
-Carefully remove all parts included in
the delivery from their packaging.
-Remove all packaging material.
- Lay the saw stand upside down on the
floor( legs facing upward).
-Push the locking pin in and tilt the leg
out-ward until the locking pin can be heard
to engage.
-Repeat this workstep with the other three
legs.
-Turn around the saw stand to the working
position. The manufacturer logo must face
toward the front so that it can be read.
-Ensure that the saw stand is stable and
that all locking pins have engaged.
The saw stand is easily aligned with the
height adjustable leg.
-Loosen lock nut and screw the leg in or
out until the saw stand is aligned level and
all four legs face against the floor.
Preparing the Mounting Brackets (see Fig. 4)
-Place both Mounting Brackets on the saw
stand in such a manner that the
labelling can be read.
-Hand-tighten both locking handles.
Extending the Saw Stand
-Unplug the saw and lock the saw arm in the
down position.
-Lift one side of the saw and place a saw
mounting bracket underneath, aligning
the carriage bolts with the mitre saw mounting
holes.
-Lower the saw down onto the bracket,
feeding the carriage bolts (A) through the
mounting holes. Secure in place using a nut
locking plate (B),then secure in place using a flat
washer (C), spring washer (D), and nut (E).
-Repeat steps to install second bracket to the
other side of the saw.
-After making sure both brackets are parallel
to each other, finger tighten all four nuts (E) to
hold in position.
(See Fig. 6-7)
Long workpieces must be underlaid or support-
ed at their free end.
-Place your long workpiece onto the saw table
of the power tool.
-Loosen locking knobs with bolt (5) and pull
the table extension out to the desired clearance.
-Retighten the locking knobs with bolt (5).
-Loosen locking knobs and adjust the height
of the workpiece support so that the workpiece
rests level.
The workpiece must be positioned level on the
power tool's saw table.
-Retighten the locking knobs (4).
Mounting Workpiece Supports (see Fig. 3)
-Insert the workpiece support (2) into the
table extension.
-Tighten the locking knob 4 to lock the
workpiece support.
-Repeat the worksteps with the second
workpiece support.
Fastening the Power Tool to the Mounting
Brackets (see Fig. 5)
Model No.MSS507F ⼁Contact us: Customerser[email protected]

WARRANTY
10
This frontierproduct carries a one-year warranty against defects in workmanship and
materials. This product is not guaranteed against wear or breakage due to misuse and/or
abuse.
Made in China
Warranty
Model No.MSS507F ⼁Contact us: Customerser[email protected]