Fu kuang hui Mp310 User manual

MP310 User Manual

Subject

Operational Notes ........………...…….….............3

Accessories .....................................……...........7

LCD .................................................……...........8

Turning the power on/off .................……...........9

Playing MP3 music ..........................……......... 10

Use menu under the playing mode ....…...........12

Voice Recording Function ...................……......14

The menu under Voice Recording mode .….....17

Exit the voice recording mode ...............….......19

To Delete files .....................................……......20

EQ (Equalizer) ....................................…..........22

Repeat mode ......................................…..........24

The Backlight ......................................…….......27

Examine the utilization of the internal memory .29

USB Connection .......................................…....30

System Requirements .................................….31

Installation of Manager Software .................….32

How to use Digital Audio Management System .33

Sending files to Digital Audio ......................…...34

Sending files from Digital Audio to PC .........…..37

Formatting the memory of Digital Audio ......…...39

To Delete files ........................................……....41

To refresh USB connection ....................……....43

Internal Memory Display .........................……...44

Pre-listen ................................................……....45

Trouble Diagnosis ................................…..........47

Fixtool User Manual……………………………….52

Fechnique Spec .....................................…….....56

Operational Notes

●If the Mp3 player will not be operated for a

prolonged period, remove the batteries to avoid

possible damage caused by electrical leakage.

●The Mp3 player should be kept in areas free

from extreme temperature changes, moisture

and dust.

●Set the HOLD switch to the release position

before operation.

●Do not drop the player, which probably

cause battery fall off or damage its surface.

Battery Status

(Time unit: hour)

Battery Digital Audio

Alkaline battery

Size AAA×1

*Battery life may vary with different using

condition, manufacturer and manufacture date.

*Please change the battery under following

conditions:

◆Indicator appears and display the

“Low Battery” then shut down.

◆All buttons make no response and are not

workable even after the battery is taken out and

reinstalled.

Note:

To avoid static electricity, please If possible,

avoid operating the player in extremely dry

environment.

If the player stops running under proper

operation, please reset it by taking out battery

Accessories

AAA Battery

LCD

Repeat modes include Repeat, Repeat All, Random,

Installation CD USB Cable

Stereo Phone Manual/

Maintenance Certificate

Pla

eat mode Hold icon

Batter

indicator

e of the son

Current situation

The sin

er and the son

Pla

back time

Preview and Normal (Normal mode isn’t illustrated

in the figure.)

Equalizer modes include Jazz, Classic, Rock, Pop

and Normal

Turning the power on/off

The power will be turned on when PLAY/STOP button is pressed momentarily. In 2 seconds, a

glorious picture with blue backlight appears. The backlight will be turned on by user setting and will

last different seconds if some button is pressed; if not, the backlight will be automatically turned down

after user setting seconds.

Pressing PLAY/STOP button for more than

3 seconds until “Power OFF” appears on the

screen, then it’s safe to turn the power off.

Playing MP3 music

1. Turning on the power by pressing PLAY/

STOP button momentarily, you could see the

following interfaces: the 03-33 means there

are 33 songs in the Digital Audio and it’s the

third.

2. When you press PLAY/STOP button again,

the current track will be played as shown

above. The top left corner is the playback

time indicator.

3. If you want to select previous/next piece,

turn the rolling wheel up and down to get the

track. The music will stop if you press PLAY/

STOP.

4. By pressing the PLAY/STOP button for 3

seconds, you could turn the power off.

5. By pressing VOL+/VOL- button, you could

control the volume under either PLAY or

PAUSE status. The volume steps (see

illustration) will increase or decrease when

the VOL+/VOL- button is pressed

correspondingly. There are 32 volume steps

and the volume level ranges from 0 to 31.

Caution

The battery status indicator may flicker while

MP3 is playing, which results from battery supply

vibration while different power is consumed.

Use menu under the playing mode

1. Press PLAY/STOP to turn on the Digital Audio

2. Press the Menu button (in the middle of the

rolling wheel). So you can see the function

menu of the Digital Audio as following:

REC Enter into record operation

EQ Equalizer mode

Repeat Repeat mode

Backlight Background light

Del File Delete audio files

Memory Info Memory information

Return Return

All the options are listed in the below table.

You may select every item by the rolling up or

down wheel.

1. You can use Last or Next button to select

every item in the function menu and press

Mode button to enter the function.

2. When you select “Del File”, you will enter

the Delete interface. More information is to

be mentioned behind.

3. The Digital Audio would pops up a dialog

box about the capacity of the memory when

the “Memory Info” is selected. With no button

being pressed, it will return to Play interface

after 2 seconds. You can see your Digital Audio memory as following:

Voice Recording Function

1. After turning on the power by pressing PLAY/

STOP button, press the Menu button (in the

middle of the rolling wheel), and then you

can see the menu as illustration.

2. Select REC item, enter into the interface of

Voice Recording (See illustration)

Total Memory

128M Byte

3. Now you can select the files to be played by

the up/down button. Press the PLAY/STOP

button to listen to the recorded files (see the

left illustration) If there are no recorded files,

the interface would be as following(see the

right illustration):

4. Then press Mode button (in the middle of

rolling wheel), you will see the function menu

under the Voice Recording mode as following

left illustration. Select Record in menu

and press Mode button to start voice

recording. The Recording interface is presented

as the following right figure.

5. You could stop recording by pressing PLAY/

STOP button momentarily and exit from

Voice Recording mode and switch to MP3

function by select Function menu.

Note: While recording, all buttons except

PLAY/STOP or Hold button are not workable.

The menu under Voice Recording

mode:

You can use the function menu to operate

the Digital Audio under Voice Recording mode:

1. Turn on the Digital Audio by pressing Play/

Stop button.

2. Press Mode button (in the middle of rolling

wheel), select REC and press Mode button

again to enter the interface of Recording.

3. In the Voice Recording interface, you will see

the function menu in the Recording mode by

pressing Mode button (See illustration)

Music Mode

RECORD

Del REC File

Memory Info

Backlight

Return

There is 6 items in the menu as showing.

They denote such functions differently as: return

to the Music mode, voice record, delete recorded

files, display information about the memory,

backlight, return to current interface

Exit the voice recording mode

Completing recording, if you want to enjoy

the music, you can exit the Voice Recording mode

and switch to the Music mode using the menu.

1. Press Mode button (in the middle of the

rolling wheel) in the Voice Recording

mode to pops up the menu as following:

2. Use Last/Next (the upside/downside of

the rolling wheel) to select Music Mode

in the menu.

3. Press the Mode button to confirm, and

then it will return to Music mode.

To Delete files

If you want to delete the files in the Digital

Audio, you may do it by using menu. Also you

can use the presented Digital Audio Manager Software to do so (more is to be mentioned behind).

You can delete songs in the Digital Audio by

do following acts:

1. Press Play/Stop button for a while to turn on

the Digital Audition.

2. Press Menu button (in the middle of the rolling

wheel) to get the function menu.

3. Select Del File by NEXT/LAST ( the upside/

downside of the rolling wheel) in the menu.

4. Press Mode button to confirm the selection.

Then following display will appear. The upper

row shows which tract you have selected

and the bottom row shows the name of the

song.

5. Now you are allowed to select the files to be

deleted. Press Mode button (in the middle of

the rolling wheel) to pops up dialog box of

delete as illustration. In this dialog box, press

Mode button to confirm and if you will not

delete the file please press any key to return

to menu.

EQ (Equalizer)

You can select different mode according to

different music.

1. Press Play/Stop button to turn on the Digital

Audio.

2. Press Mode button to get the menu.

3. Select EQ in the menu by the Next/Last

button.

4. Press Mode button and the EQ menu would

pops up.

5. Select the Equalizer mode

There are five modes: JAZZ, CLASSIC,

ROCK, POP and NORMAL The list of equilibrium

effect pops up after selecting EQ as following:

JAZZ

CLASSIC

ROCK

POP

NORMAL

Return

You can adjust the modes by the EQ menu.

You could experience perfect Jazz, Classic, Rock,

Pop sound effect by choosing suitable corresponding mode. Normal mode could bring you original

sound effect.

If you don’t want to change current settings,

you can choose Return to exit

Repeat mode

If you’d like to listen to a song again and again,

then you need change the Repeat mode.

1. Press Play/Stop button to turn on the

Digital Audio

2. Press Mode button (in the middle of the

rolling wheel) to get the menu

3. Select Repeat in the menu using Next/

Last button (the upside/downside of the

rolling wheel)

4. Press Mode button to get Repeat menu:

Selecting Repeat, you can see the following

interface and the Play Repeat mode can be

changed. The mode includes: Random, Normal, Repeat All, Repeat, and Preview mode.

Random

Normal

Repeat all

Repeat one

Preview

Return

Repeat All Random

Preview Mode Normal

Repeat: Plays the current MP3 music repeatedly.

Repeat All: Plays all MP3 music in order repeatedly

until another operation is performed.

Random: Plays all MP3 music at random and then

stops.

Preview: Plays every first 10 seconds of all MP3

music in order and stops after the last music has

been played.

Repeat

Normal: Plays the MP3 music in order and stops

after the last music has been played.

If you don’t want to change current settings,

you can choose Return to exit.

The Backlight

You will be attached to the blue backlight. You

can setup how long the backlight will last according

to your demands.

1. Select Backlight in the menu whether in

the Music or in the REC mode.

2. Press Mode button and enter the menu

of backlight as following:

You may choose to turn off the backlight or

let the backlight on for 5, 10, 15,or 20 seconds

each time the button is pressed.

Off means the backlight won’t be on in all

cases. So the battery life will be prolonged.

5Sec,10Sec,15Sec,20Sec means the backlight

will be on for 5, 10, 15,or 20 seconds each

time the button is pressed.

Examine the utilization of the internal memory

You could examine the utilization of the memory

without being connected to the PC.

1. Press Play/Stop to turn on the Digital

Audio

2. Select Memory Info in the menu by

pressing Last/Next (the upside/downside

of the rolling wheel) button under Music or Rec. mode

3. Press Mode to confirm. The Digital

Audio will pops up a dialog box as following

to show the capacity of available memory. It will return to the Play interface after 2 seconds if there

is no button pressed. You could see the memory of the internal memory.

USB Connection

You could transmit MP3 files through USB port

of your PC.

1. Make sure your PC support USB devices.

(Refer to the manual of your PC for the information

about hardware).

2. Connect your PC directly or by USB cable

with digital audio.

3. LCD display window will show connecting

picture if connection is finished. Just like the

illustrator below.

4. If you have installed the attached software,

the PC will automatically find the device when

the Digital Audio is connected to the PC at the first time. If not, please install the manager

software first.

We strongly recommend users install the provided management software under Windows 98/XP/2000.

System Requirements

It is important to install Digital Audio manager

software before connecting Digital Audio to PC. After putting the Installation CD into CDROM Drive,

USB Driver is installed automatically. The Digital Audio manager software requires the following

systems:

Total Memory

128M Byte

¤ IBM compatible personal computer

¤ Pentium 166 MHz MMX or faster

¤ Windows 98 SE, Windows 2000 or Windows

¤ USB Port

¤ 32MB RAM or more (64MB is recommended

for Windows 2000)

¤ 20MB free hard-disk space or more

¤ 4 ×CD-ROM drive or more

¤ Sound Card (Optional)

¤ Accessible to Internet (Recommended)

Installation of Manager Software

Put the Installation CD into CD-ROM Drive

and then it will be installed automatically. You

should click the “Next” button on installation

screens, and the Digital Audio Manager Software

and USB Driver will be installed. It will remind

you of restarting your PC when installation is

finished. At last, “/Start/Program/Digital Audio

Manager Software” is created in the Windows

Menu, and the Digital Audio icon is also created

on the Desktop window.

How to use Digital Audio Management System

First connect the Digital Audio and your PC

directly or with the USB cable. Then the Digital

Audio’s LCD Display Window will show picture

if connection is finished.

Click the icon on the Desktop Then the interface

of Digital Audio management system will be shown.

Sending files to Digital Audio

Before sending, please turn on the Digital

Audio and connect it to your PC directly or with

presented USB cable.

1. Double click the icon on the desktop.

2. Select files. First, select the folder that includes

the files to be transmitted from the

left Program Manager. Then the files in the

folder will be displayed in right column

automatically. You could also select the files

type in the menu on the top left corner to

make your operation easier.

3. Click the Download button or select the

“Download” option in the tool menu.

4. An interface of Copy will appear.

5. System will set up an EDISK directory automatically and place the non-audio files to

EDISK in the removable disk of the Digital

Audio after you download the non-MP3 or WMA files.

6. The management system will examine the

Digital Audio automatically. When the USB

cable is pulled out from the Digital Audio,

the management system won’t work.

Caution:

1) Do not pull out digital audio while a file

is being downloaded. It will do harm to

your Digital Audio.

2) If the Digital Audio cannot work by

accident, take out the battery and reinsert

it 3 seconds later. Reconnect Digital

Audio to PC.

3) If you couldn’t find the downloaded

non-audio files in the removable disk of

Digital Audio, please look into EDISK

directory.

4) While you download file in Win98 OS,

the transmitting must regard to player

displaying. We simulate the transmitting

by the player displaying motivation.

When the motivation stop, which denote

the transmitting finished, you can take

out the player safely. The player do harm

when you take out the player while the

transmitting have not completed.

Sending files from Digital Audio to

Digital Audio can also act as a removable electronic disk. You could send files in the disk to

your PC with the management system but the

audio files are not permitted to send due to copyright protection. Only files in the EDISK are

allowed.

1. Connect the Digital Audio and PC .

2. Select the files to be sent.

3. Click the Send button in the manager

software.

4. The interface of transmission would be

displayed.

Caution:

Do not pull out the digital audio while a file

is being downloaded. Otherwise it will do harm

to your Digital Audio.

It is not permitted to transmit music files for

cannot be send” if you select MP3 or WMA files.

While you transmit files in Win98 OS, the

transmitting progress must regard to player

displaying. We simulate the transmitting by the

player displaying motivation. When the motivation

stop, which denote the transmitting finished, you

can take out the player safely. The player do harm when you take out the player while the

transmitting have not completed.

Formatting the memory of Digital

Audio

Before formatting, be sure that the Digital Audio

is turned on and connected to PC.

1. Run the management system of Digital Audio

on the desktop.

2. Click Format icon, the dialog box of format

will pop up.

3. Click Start button it begins to format Digital Audio memory.

Caution:

All the files will be deleted by formatting the

memory.

Do not disconnect while formatting. Or your

Digital Audio may lose system files and cannot

be started up.

To Delete files

Besides deleting files directly by Digital

Audio, you could also achieve this by using the

management system of Digital Audio.

1. Connect the Digital Audio and PC; turn on

the Digital Audio and run management system.

2. Select the files to be deleted.

3. Click the Delete button .

You could also use the option of Deletion in

the menu.

Note:

Once a file is deleted, it won’t be restored.

This operation cannot be used to delete the files in

PC.

To refresh USB connection

For safer use while connecting Digital Audio

and PC, you could click the Connection button in

the management system of Digital Audio to refresh

the USB connection.

Internal Memory Display

The management system of Digital Audio can

display the internal memory by numbers and

figures.

In the above figure, yellow represents used

memory while green available memory

Pre-listen

After selecting a song in your PC, you could listen

to it by using Digital Audio manage system.

1. Choose the song to be listened.

2. Click the Pre-listen button on the top right

corner, and then you could enjoy pleasant

music pieces from PC. Now, the Pre-listen

Figure

Number

button changes into Stop button. Music will

stop by clicking it again. If you want to listen

to another song, you have to stop the current piece first and then go on to the next.

Trouble Diagnosis

1. The LCD display window shows nothing after

turning on Digital Audio.

·Check to see if the battery has been inserted.

·Check to see if the battery needs replacement.

·Try reinserting the battery or replace it.

·Take out the battery and insert it correctly after

5 seconds.

2. The buttons are not workable.

·Check to see if the “Hold” button is on.

·Release the Hold button.

3. No sound could be heard while playing MP3

files.

· Check to see if the volume is too low and turn

it up.

· Check to see if the Digital Audio is being

connected with computer.

· Check to see if there is any music file in the

memory.

4. I can’t download music files after connection.

· Check to see if Manager Software is setup.

· Check to see if the software is working

properly.

· Check to see if your Mother Board supports

the USB devices and needs upgrade.

5.Some songs show the playback time not continuous

Now some MP3 or WMA songs use VBR format to compress, so the player can not show the playback time

normally. You can try to compress again by selecting normal ratting.

6.Some MP3 songs can not play in the player

Now some MP3 songs use the Mpeg I Layer1 or Layer2 format compressing, but the player only support the

Mpeg I Layer3 and WMA songs, the other songs maybe play natural but will exist some problem in it. So you

try to compress the songs by Mpeg I Layer3 format.

NOTICE:

1. Please use provided format tool to format your MP3 player, it will not work if you use Windows®format

tool. If you have not installed the provided Digital Audio Management System, please use the “delete”

command to erase the files in your player. The MP3 player will be damaged if formatted under Window’s

format tool. Was genau soll das heißen?

2. When transferring files between your MP3 player and PC, please watch the MP3 player’s LCD

display. The transferring rate is displayed on the screen. The transmission is completed when the

LCD stops displaying the transfer.

3. The “Plug and Play” function only works with

Win®2000/Win® XP operating system or higher.

Under Win® 98/ Win® 98SE the driver has to be installed which is build into the Digital Audio

Management System. If the device is still not displayed, please install the files of Win® 98 driver

folder from the driver CD.

Fixtool User Manual

We strongly recommend user do not format their Mp3 player under the Window’s formatting system without installing our

audio management software. This is because it’ll lead the player halted or unable to function normally. However, if the above

situation occurs, this fixtool is for users to solve the problem.

Please follow the steps for the installation and manual (Under Window XP):

1.After installing the Fixtool in the system, restart the PC.

2.Take out the battery in the halted player and connect the player to PC with USB cable, then put in a new battery into the

player.

3.Press the “Play” button for 5 seconds, the PC will automatically detect a “Recovery Device”

click “Next”:

Choose the option of installing the system automatically, and the system should be able to detect a “Player Recovery

Device”. If not, follow the installation window and click “next”:

Click “Next”:

If system need you choose directory for installation, please select the directory such as “C:\program

files\digital\AudioMS”.

After installing the hardware, click “Format AudioMS” in the “Digital AudioMS Player” menu (as shown below):

The system should be able to detect the device this time, click “next” to continue:

Click “next” the system will select device automatically, if the system can not be able to run automatically,please choose the

your installation path. Installation path as below “C:\program files\digital\AudioMS”

After finding the device, run the “Format AudioMS” in the “Digital AudioMS Player” menu and click “start” to start

formatting. The player should be able to function normally after the formatting process.(only if the start button show effective ,

and the media option and capacity option show correctly number, it proves you get correctly device.)

Choose “unplug or eject hardware” in the toolbar, then remove your player safely. The player should be able to function

normally now.

Note: Please refer to the above instructions for Window 2000 and 98.

Fechnique Spec

Memory Size 64/128M

Volume adjustment 32 level

LCD 96*26 pixel

Size 95*32*21(mm)

SNR 90dB

Output Frequence 20HZ-20KHZ

Record Format ADPCM

Compress Rate 32Kbps-256Kbps

Note:

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more

of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.