Fuho IP901 User manual

IP901 User’s Manual
Page 1
IP901-IP-CAM
USER MANUAL

IP901 User’s Manual
Page 2
Cautions
1. Read this user manual before use
2. Keep this user manual accessible
3. Follow instruction
4. Keep this unit away from cleanser
5. Keep this unit dry in ventilation
6. Give way to ventilation outlet
7. Power cord must be fixed properly
8. To avoid damage, unit must not be stuffed or be splashed with something
9. Do not repair this unit on your own
10. Please contact local dealer for the following condition:
a. Power cord damaged
b. Showered unit
c. Failure in operation
d. Unit dropped or cabinet damaged
11. Repairing components must be approved by original manufacturer.
12. Ground wire of outdoor image source must be well connected to the ground to prevent from
thunder attack
13. Power cord and outdoor image source cable should be detached in case of thunder attack
Warning
Only qualified engineer can detach the cover. There is nothing inside for end users.
Cover must not be removed in case of power on.

IP901 User’s Manual
Page 3
CONTENT
1. OUTLINE
1.1 INTRODUCTION ...................................................4
1.2 FEATURE ................................................................5
1.3 ACCESSORY ..........................................................5
1.4 SYSTEM REQUIREMENT ...................................5
1.5 PANELS ...................................................................6
1.5.1 FRONT PANEL ....................................................6
1.5.2 REAR PANEL ......................................................6
2. INSTALLATION
2.1 CABLING ................................................................8
2.2 SURVEILLANCE SOFTWARE ............................11
2.3 ETHERNET FRAMEWORK & CONNECTION .13
2.3.1 PC TO IP-CAM CONNECTION ........................13
2.3.2 INTRANET CONNECTION ...............................16
3. OPERATION
3.1 LivePlayer SURVEILLANCE SOFTWARE ........19
3.1.1 LivePlay SOFTWARE INTERFACE .................19
3.1.2 LivePlayer INTERFACE SETUP .......................21
3.2 IE BROWSER SETUP CAMERA FUNCTION ..29
3.2.1 Web Server AUTHORIZATION ........................30
3.2.2 Status ...................................................................31
3.2.3 View .......................................................................32
3.2.4 System ....................................................................33
3.2.5 Network .................................................................34
3.2.6 Image .....................................................................35
3.2.7 User ........................................................................35
3.2.8 Alert .......................................................................36
3.2.9 Factory Default Function .....................................38
3.2.10 Restart Function .................................................38
3.2.11 Upgrade ...............................................................39
4. ELSE
4.1 SPECIFICATIONS .................................................40

IP901 User’s Manual
Page 4
1. OUTLINE
IP-CAM is a low cost provision of network surveillance facility which transmits images on
network to remote PC in format of compression technology. Monitoring, storage and recognition
on line are provided by IP-CAM. Image transmission remains the same quality on both ends of
server site and remote site. Single image source can be transmitted to multi ports saving lots of
cabling overhead.
1.1 INTRODUCTION
Dual compression technology JPEG & MPEG-4, remote site operator can access to the server
site via IE browser to secure personal safeguard and property. IP-CAM works with existing
digital network transmission system. LivePlayer software provides functions of live monitoring,
monitoring setup conditions & motion/schedule recording.

IP901 User’s Manual
Page 5
1.2 FEATURE
;Image & audio transmission via network
;Dynamic IP & static IP support
;Dual compression technology JPEG & MPEG-4
;Digital alarm I/O
;RS-485 for PTZ control
;LivePlayer client software
;Built in motion detection & recording functions
;IE browser remote monitoring & setup support
;Firmware upgrade via IE browser on line
1.3 ACCESSORY
[1] . IP-CAM
[2] . CD ROM
Remarks
[1] . Please contact local dealer in case of accessory shortage
[2] . IP-CAM may be damaged & warranty void in use of other power adaptors
1.4 SYSTEM REQUIREMENT
;Pentium4 or above
;Windows 2000/XP OS
;Protocol comply to 802.11 or ADSL network
;Microsoft Internet Explorer 6.0 or above
;Microsoft Codec Installation Package for Windows Media Player 6.4 or above
( http://www.microsoft.com/windows/windowsmedia/format/codecdownload.aspx )

IP901 User’s Manual
Page 6
1.5 PANELS
1.5.1 FRONT PANEL
Microphone
Build-in Microphone
1.5.2 REAR PANEL
DC +12V
Power input port receives 12VDC power
Video Out
Video output port provides images to monitor or recording devices
RS-485
RS-485 control port for PTZ control
LAN
RJ-45 10/100 Based-T Ethernet transmission port
Reset Button
Press this button to restart

IP901 User’s Manual
Page 7
ALARM I/O
Alarm input/output port two sets for digital sensor input one set for digital alarm output
Definition of the pins
1. +12VDC
2. digital sensor input #1; Hi active
3. digital sensor # 2; Hi active
4. GND。
5. digital output out
6. digital output in
caution: pin #2 & pin #3 are individual input ports Hi active input voltage rated 12VDC
pin #5 & pin #6 are the same output port normal open alarm close
POWER LED
Power indicator power on indicator red
LAN LED
Network indicator LED ON LAN working

IP901 User’s Manual
Page 8
2. INSTALLATION
2.1 CABLING
1. Power Input
Plug in the power adaptor which supplies +12VDC. IP-CAM could be damaged of
improper voltage input. Power LED turns to red in five seconds IP-CAM system
activated.
2. Plug in Ethernet Cable
Plug the cable in the Ethernet port with “LAN＂ mark for Ethernet connection.
Ethernet port
Power Input

IP901 User’s Manual
Page 9
3. Video Output
“VIDEO OUTPUT＂ is to be connected to CCTV monitor for live monitoring. The
video output format is 1 Vp-p Composite Video Signal, 75 Ω
4. RS-485 Connection
RS-485 --- Pan Tilt Control Port. User can setup pan tilt control on IE browser.
Please keep alert on the polarity D+ & D- of RS-485 port.
RS-485
Video Output

IP901 User’s Manual
Page 10
2.2 SURVEILLANCE SOFTWARE
Please use the enclosed CD ROM to install the software
1. Put the CD ROM in CD drive
2. Execute the file “Liveplayer_Setup.exe” to start installation. This software promptly
supports OS of English, traditional Chinese & simplified Chinese.
3. Click “Next” to initiate software
installation
4. Click “Next” in the dialog of
“Choose Components”
5. Choose the default directory

IP901 User’s Manual
Page 11
6. Execute Codec Installation Package
to download software via internet
7. Click “Close” upon installation
finished
8. Click “start” Δprogram files”
ΔIPCam”ΔLivePlayer”

IP901 User’s Manual
Page 12
2.3 ETHERNET FRAMEWORK & CONNECTION
IP-CAM can be connected to DSL modem or hub. IP-CAM will start detecting DHCP
protocol upon power input. IP-CAM enables DHCP protocol to work with NAT IP address when
NAT router in use. Default IP address 192.168.1.200 starts working when NAT router not in use.
Suppose 192.168.1.200 has been occupied by other device. Other device must be shut down
beforehand until IP-CAM finishes IP setup.
2.3.1 PC TO IP-CAM CONNECTION
1. Use Cat5 Cross-over Cable to connect PC
Cat5 Cross-over Cable (EIA 568A/B）layout & definition
2. Video server default setup as follows

IP901 User’s Manual
Page 13
3. Setup IP address of PC’s LAN card same as IP-CAM’s domain.
In condition of Windowns-2000/XP OS
a. Select “My Network Places” by clicking mouse on the right.
Click “properties” accordingly.
b. Select “Local Area Connection” by clicking mouse on the right.
Click “Properties” accordingly.
c. Select ”TCP/IP” and click “Properties”

IP901 User’s Manual
Page 14
d. Select “Use the following IP address” to input IP address, Subnet mask and
Default gateway. Click “OK” accordingly.
4. Follow the following procedure to make sure IP address correct.
a. Click “START” ΔRUN” and input “cmd”.
Click “OK”.

IP901 User’s Manual
Page 15
b. Enter DOS and input “ipconfig”. Click “enter” to inspect IP address, Subnet
mask and Default gateway.
Please logout and login if IP incorrect.
5. Connection
a. Execute the client software LivePlayer. Click “Setup” and “Refresh” to search
IP-CAM. It takes time to search the IP-CAM. Please be patient. Alert dialog
pops up upon video server found. Please review 3.1.2 for details.

IP901 User’s Manual
Page 16
b. Click “View” and “OK” to start connection.
2.3.2 INTRANET CONNECTION
1. Cat 5 cable must be used in condition of connection via router, DSL modem and hub.

IP901 User’s Manual
Page 17
2. Please make sure PC and video server same domain.
3. IP-CAM detects DHCP when system starts working. IP-CAM enables DHCP protocol to
accept IP address from NAT when NAT router detected. Default IP address becomes
192.168.1.200 when NAT router not detected. Suppose there is an IP address
192.168.1.200 on internet. This device must be turned off prior to IP-CAM renew the IP
setup.
4. Connection
a. Execute client software “LivePlayer”. Click “Setup” and “Refresh” to start
IP-CAM search. Please be patient for waiting IP-CAM search. Click “OK” by
the time video server detected. Please review 3.1.2 for details.

IP901 User’s Manual
Page 18
b. Tick the item “View” and click “OK” to start connection.

IP901 User’s Manual
Page 19
3. OPERATION
3.1 LivePlayer SURVEILLANCE SOFTWARE
IP-CAM provides LivePlay client software. Four units of IP-CAM can be monitored and
managed at the same moment.
3.1.1 LivePlay SOFTWARE INTERFACE
1. LivePlay icon comes up on the desktop after installation. Double clicks on the mouse to
activate LivePlay software. Screen shot and control panel displays as follows:
2. Click “Change to Small Panel” for small size panel.

IP901 User’s Manual
Page 20
3. Definition of buttons in the control panel
Exit
Exit LivePlayer
Hide the Panel
Minimize LivePlayer
Quad View
Viewing four channels at the same time
Single view
Viewing single channel
Setting
Entering setup menu to setup internet server, recording, system configuration,
alarm……
View recorded files
Click this button to execute the folder in explorer. Default directory can be
found C:\Program files\IPCam. Recorded files can be found there.
Audio volume
PC’s Sound Card Volume Adjustment
Can monitor the sound at the remote site.
Mute
Mute the sound of sound card.
Change to big panel/change to small panel
Change the size of the panel.
Hide the status menu
Hide the channel selection and alarm status to clarify the screen shot.
Camera 1-4
Inspect the intended channel in single channel status. Input audio in quad status.
motion detection status
Motion Detection Indicator
IP-CAM gives alert when motion detected.
Camera record status
Recording Indicator
PC keeps writing video files in the hard drive.
Digital input trigger status
Digital Sensor Input Indicator
Indicator of Digital Input
Left --- Port # 1
Right --- Port # 2
Video Server comes with two digital input ports to receive alert from sensor.
Digital output alarm status
Digital Alarm Output Indicator
Indicator gives alert when IP-CAM delivers digital output.