FujiFilm DR-ID 670 User manual

897N102735
This Operation Manual describes details on how to operate the DR-ID 670 and
cautions to be observed when operating it.
After reading this manual, store it nearby the DR-ID 670 so that you can see it
whenever necessary.
DR-ID 670
Operation Manual
1st Edition : May 2013
For Safe Operation
System
Conguration
(Product Overview)
Basic Operation
Daily Inspection and
Maintenance
Appendix
Maintenance and
Inspection

ii DR-ID 670 Operation Manual 897N102735

iii
DR-ID 670 Operation Manual 897N102735
Introduction
DR-ID 670 is an X-ray equipment which acquires a general radiograph from the indirect-conversion at
panel sensor. The detector of at panel sensors features 150 micron pixel pitch, a wide 16-bit dynamic
range and exposure times up to 3.8 seconds.
Intended Use
The Fujilm DR-ID 670 provides digital image capture for radiographic examinations.
It is intended for use in general projection radiographic applications wherever conventional screen-lm
systems or CR systems may be used. DR-ID 670 is a device that provides images, which diagnostic
image process is not implemented, to image collecting console. It is not designed for mammography,
uoroscope, tomography or angiography.
About This Manual
This Operation Manual includes descriptions of matters necessary when using the DR-ID 670 such
as the equipment overview, operation procedures and precautions to observe, as well as daily
inspections and maintenance.
Refer System Operation manual (which describe about image correction console, and prepared by
System Integrator), about image collecting console and diagnostic images process.
Accompanying documents were originally drafted in the English language.
Important information
DR-ID 670 consists of DR-ID 600MP, DR-ID 670MC and DR-ID 601SE/DR-ID 602SE/DR-ID 611SE/
DR-ID 612SE/DR-ID 613SE.
DR-ID 601SE, DR-ID 602SE, DR-ID 611SE, DR-ID 612SE and DR-ID 613SE :Wireless communication
mode or wired communication mode is available. When used in wireless communication mode, an
access point
*
1
, battery pack (optional) and battery charger (optional) are required.
*1 In the countries other than the U.S., an access point is not included as a component of the system.
For details including installation, consult our ofcial dealer.
Each at panel sensor complies with IEC 62220-1 (MEDICAL ELECTRICAL EQUIPMENT -
CHARACTERISTICS OF DIGITAL X-RAY IMAGING DEVICES - ) as a general X-ray radiography
equipment.
Installation may only be conducted by authorized service personal.
CAUTIONS
1. No part or all of this manual may be reproduced in any form without prior permission.
2. The information contained in this manual may be subject to change without prior notice.
3. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from
installation, relocation, remodeling, maintenance, and repair performed by other than dealers
specied by FUJIFILM Corporation.
4.
FUJIFILM Corporation shall not be liable for malfunctions and damages of FUJIFILM Corporation
products due to products of other manufacturers not supplied by FUJIFILM Corporation.
5. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from remodeling,
maintenance, and repair using repair parts other than those specied by FUJIFILM Corporation.
6. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from
negligence of precautions and operating methods contained in this manual.
7. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from use
under environment conditions outside the range of using conditions for this product such as
power supply, installation environment, etc. contained in this manual.
8. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from natural
disasters such as res, earthquakes, oods, lightning, etc.
This system is classied as a medical device under EC Directive 93/42/EEC.
Process waste correctly, as stipulated by local law or any regulations that apply.
Caution : Rx Only in the United States (Federal law restricts this device to sale by or on the order of
a physician.)

iv DR-ID 670 Operation Manual 897N102735
Open-Source Software Used in This Product
This product uses third party’s software that is made available as open source software or free software.
For information on open source software used in this product, please see the attached CD. Source
codes for certain type of open source software used in this product are available at delivery cost.
If you would like to receive such source codes, please contact FUJIFILM dealer or the service representatives
at the agency from which you purchased this product. (Please be noted that any inquiries concerning the
contents of source codes should be directed to original licensers of open source software.)
Note : FUJIFILM has successfully performed verication and validation testing on all third party
software and has conrmed its suitability to be used in this system.
Patent Marking
DR-ID 601SE/DR-ID 602SE are covered by one or more of the following US patents: US 5,654,084/
US 5,681,666/US 6,413,645 or international equivalents.
Trademarks
All company names and product names described in this manual are the trademarks or registered
trademarks of FUJIFILM Corporation or their respective holders.
Windows is the registered trademark of US Microsoft Corporation in the U.S.A. and other countries.
Copyright © 2013 FUJIFILM Corporation. All rights reserved.

v
DR-ID 670 Operation Manual 897N102735
Contents
Introduction...........................................................................................................................iii
Chapter 1 For Safe Operation
1.1 Safety ......................................................................................................................1-1
1.2 Electromagnetic Compatibility (EMC)......................................................................1-9
1.2.1 DR-ID 670................................................................................................................1-9
1.3 Precautions in Using the DR-ID 670 .....................................................................1-14
1.3.1 Handling.................................................................................................................1-14
1.3.2 Before Exposure....................................................................................................1-15
1.3.3 During Exposure....................................................................................................1-16
1.3.4 During Cleaning.....................................................................................................1-16
1.3.5 Storage ..................................................................................................................1-16
1.3.6 Precautions Related to the Load Applied to the Flat Panel Sensor.......................1-17
Chapter 2 System Conguration (Product Overview)
2.1 DR-ID 670 ...............................................................................................................2-1
2.1.1 System Conguration ..............................................................................................2-1
2.2 Unit Names and the Functions................................................................................2-2
2.3 Locations of Labels and Signs ................................................................................2-3
2.3.1 Locations of Labels..................................................................................................2-3
2.3.2 Safety and Other Symbols.......................................................................................2-7
Chapter 3 Basic Operation
3.1 Preparing the Flat Panel Sensor .............................................................................3-1
3.1.1 Type of Flat Panel Sensor .......................................................................................3-1
3.1.2 Number of the Connectable Flat Panel Sensors .....................................................3-1
3.1.3 Connecting/Disconnecting the Flat Panel Sensor Connector..................................3-2
3.1.4 Inserting/Removing the Flat Panel Sensor into/
from the Radiographic Examination Stand ..............................................................3-3
3.1.5
Changing the Direction of the Flat Panel Sensor Connector ........................................3-6
3.1.6 Charging the Battery Pack (Optional) for the Flat Panel Sensor .............................3-6
3.1.7 Installing/Removing the Battery Pack (Optional) for the Flat Panel Sensor ............3-7
3.2 Starting Up and Shutting Down the DR-ID 670.......................................................3-8
3.2.1 Starting Up the DR-ID 670.......................................................................................3-8
3.2.2 Shutting Down the DR-ID 670 .................................................................................3-8
Chapter 4 Daily Inspection and Maintenance
4.1 Daily User Inspection and Maintenance......................................................................4-1
4.1.1 Periodical Inspection................................................................................................4-1

vi DR-ID 670 Operation Manual 897N102735
Appendix A Specications
A.1 Specications ..........................................................................................................A-1
A.1.1 Reduced Equivalent (DR-ID 670) ........................................................................... A-1
A.1.2 Power Supply Conditions........................................................................................ A-1
A.1.3 Environmental Conditions....................................................................................... A-1
A.1.4 Image Performance ................................................................................................ A-1
Appendix Z Precautions for Exposure
Z.1 Precautions for the Automatic X-ray Detection Function.............................................Z-1
Z.1.1 Precautions for Making an Exposure.......................................................................Z-1
Z.1.2 Precautions Related to the X-ray Exposure Time....................................................Z-2
Z.2 Other Precautions ...................................................................................................Z-3
Z.2.1 Precautions for Exposure of a Subject in Relatively Large Contrast .......................Z-3
Z.2.2 Precautions for DR System .....................................................................................Z-3
Z.2.3 Precautions for Assuring the Radiation Field...........................................................Z-3
Z.2.4 Precautions Related to Continuous Operation ........................................................Z-3
Z.2.5 Precautions during Calibration.................................................................................Z-4
Z.2.6 Precautions for Exposing the Flat Panel Sensor to X-ray........................................Z-4
Appendix O Use of Optional Items
O.1 Optional Items ....................................................................................................... O-1
O.2 Using the SE Storage Case ................................................................................... O-2
O.3 Using the Retaining Bracket for MP ....................................................................... O-3
O.4 Cradle..................................................................................................................... O-4
Maintenance and Inspection

1-1
For Safe Operation
1
DR-ID 670 Operation Manual 897N102735
Chapter 1 For Safe Operation
1.1 Safety
Before using the DR-ID 670, read this section thoroughly to ensure that you use the product properly.
Electric Shock Warnings and Cautions
WARNING
The power supply to the DR-ID 670 is AC100 to 240V.
To avoid electric shocks, users should always take the following precautions:
● Never open any covers of the equipment.
● Install the equipment in a location where it will not be exposed to water.
● Check that the equipment is securely earthed.
● Check that all of the cords and cables are completely and securely connected.
WARNING
Do not touch the patient’s body while touching the control cabinet. Otherwise, the patient may
receive an electric shock.
WARNING
Do not use a multiple tap connector or extension cable for powering the devices constituting
the system. Otherwise, re or electric shock may occur due to the electrical load exceeding the
allowable limit.
WARNING
Observe the following precautions when using the cables.
● Turn off each unit before connecting/disconnecting the cable.
Do not touch the plug and connector with wet hands. Otherwise, electric shock may result,
causing death or severe injury.
● Hold the plug or connector when removing the cable.
Pulling the cable or carrying by holding it may damage the cable, causing re or electric shock.
● Do not damage or remodel the cable.
Do not place a heavy object on the cable or lay it under the at panel sensor. Do not step on,
pull, forcibly bend, or bundle the cable. Otherwise, re or electric shock may result.
● Do not use the at panel sensor for the radiographic examination stand if its cable becomes
overloaded. Otherwise, the cable may be damaged, causing re or electric shock.
WARNING
Do not turn on the system with dew condensation on the at panel sensor. Otherwise, re or
electric shock may result.

1-2
For Safe Operation
1
DR-ID 670 Operation Manual 897N102735
WARNING
Do not use the equipment in a location where metal particles could come into the equipment.
This may cause an electric shock.
WARNING
Do not disassemble or remodel the equipment. Otherwise, re or electric shock may result.
Keep away from the parts inside the product, which may cause electric shock. If you touch
them accidentally, death or severe injury may result.
WARNING
Do not hit or drop the equipment or subject it to severe shock. Otherwise, the equipment may
be damaged. If the damaged equipment is used, re or electric shock may result.
WARNING
Before using the at panel sensor (DR-ID 601SE, DR-ID 602SE, DR-ID 611SE, DR-ID 612SE and DR-ID
613SE), make sure that the battery cover or battery pack is attached. If not attached, an electric shock
may result.
WARNING
Make sure to use the optional parts and accessories recommended by us. Failure to use the
optional parts and accessories recommended by us may result in damage to the equipment
and/or electric shock and injury.
CAUTIONS
As the cables of the equipment are long, be careful not to entangle the cables during use.
Also, be careful not to trip over the cables. Falls could result in injury.
CAUTIONS
Follow the specied procedure when turning off the equipment. Otherwise, the at panel
sensor could be damaged by thermal shock.
CAUTIONS
Do not store magnetic media near the DR system and control cabinet. Otherwise, magnetism
generated by the equipment may cause the data to be lost.
CAUTIONS
Keep the equipment away from patient’s body uids, chemicals, water, etc.
Otherwise, it may become damaged, causing re or electric shock.
If necessary, protect the at panel sensor by covering it with a disposable bag.
Explosion Warnings
WARNING
Because this equipment is not explosion-proof, do not use combustible and explosive gases
near the equipment.

1-3
For Safe Operation
1
DR-ID 670 Operation Manual 897N102735
WARNING
Flammable gasses may stay in the room after disinfection. Ventilate the room well before
powering on the equipment following disinfection.
Warnings for Abnormalities
WARNING
If any of the following occurs, immediately turn off the power of each unit, unplug the power
cable from the outlet, and then contact a FUJIFILM dealer.
● When smoke, strange odor, or abnormal sound is present.
● When a foreign object (such as a metal object) or liquid enters the product.
● When the equipment is dropped or hit and is damaged.
Installation Precautions
CAUTIONS
Do not install the equipment in a location with the following conditions.
● Where the temperature changes sharply.
● Close to heat sources such as a heater.
● Where the equipment may be exposed to water due to water leakage or ingress.
● Where corrosive gas may be generated.
● Where there is excessive dust.
● Where the equipment is subject to frequent or excessive vibration/shock.
● Where the equipment is exposed to direct sunlight.
● Where there is no ventilator.
CAUTIONS
For veterinary or mobile applications, contact a FUJIFILM dealer.
CAUTIONS
Use the system indoor in wireless communication mode. For details, contact a FUJIFILM dealer.
CAUTIONS
Do not place any object in a place where removal of the power cable is prevented.
Connection Instructions
WARNING
Make sure that the devices to be connected to the equipment are authorized for connection.
WARNING
When the DR-ID 670 is connected to X-ray equipment, make sure that the equipment complies
with IEC 60601-1.

1-4
For Safe Operation
1
DR-ID 670 Operation Manual 897N102735
Precautions on External Network Connection
CAUTIONS
When a setting of the network to which the equipment is connected has been changed,
check that the change does not affect the system operation and take measures if
necessary.
The setting change may include the following:
● Change of connection destination
● Addition of devices
● Removal of devices
● Update of devices
● Upgrade of devices
Warnings and Cautions on Network
WARNING
Make sure to use the optional parts, accessories and networks recommended by us. Failure to
use the optional parts, accessories and networks recommended by us may result in damage to
the equipment and/or electric shock and injury.
CAUTIONS
Connect to the Ethernet Network of 1000BASE-T, 100BASE-TX, or 10BASE-T prescribed in the
IEEE standard 802.3.
Do not connect telephone lines to LAN connector. Only UTP-type straight LAN cables of 4-pair
Category 5 cable (CAT 5E) or higher are appropriate for connection to this connector.
CAUTIONS
After connecting this system to the network with other systems,conrm that the other systems
are not affected. If they are affected, take countermeasures such as network separation.
System Isolation Instructions
WARNING
To ensure complete system isolation, never install any unauthorized accessories or other such
items.
When it is necessary to install authorized accessories or optional items, contact a FUJIFILM
dealer.
WARNING
Keep equipment other than those used for patients out of their reach to ensure appropriate
system isolation.
WARNING
In normal use, have a patient take a proper positioning for exposure. The operator should operate the
system in a place where safety from radiation is ensured. The operator should also make sure before
exposure that no one but the patient is in the exposure area and the operating area of the system.