FujiFilm FinePix S1 Pro User manual

FUJI PHOTO FILM U.S.A., INC. CAMERA REPAIR 1100 KING GEORGE POST RD. EDISON, NJ 08818-7828 1-800-659-3854
PLACE
POSTAGE
HERE
Cleaning
Your
FinePix S1 Pro
CCD
FUJI PHOTO FILM U.S.A., INC.
Attn: Camera Parts Department
1100 King George Post Road
Edison, NJ 08837
[phone] ext. 3452 Phone
[phone] FAX
PHOTOGRAPHIC SOLUTIONS, INC.
http://www.photosol.com
7 Cranston Way
Buzzards Bay, MA 02532
[phone] Phone
[phone] all US, all US territories & all Canada
(508) 759- 9699 FAX
ECLIPSE OPTIC SOLUTION
Contents: 59ml. (2Fl oz)
SENSOR SWAB
Contents: 12 swabs

4. Hold down both the self-timer and the AE lock "AE-L"
buttons and switch camera on.
5. Press the shutter button. The mirror will then swing up and
the shutter opens. The camera will remain open while the AC
power adapter delivers power to the camera.
6. Hold the camera so that light shines on the CCD to check
the CCD surface.
* If there is dust on the CCD surface, contact an authorized
Fuji Film dealer to request cleaning or clean the CCD as
described below. If there is no dust on the CCD surface,
proceed to step 5 below of "Cleaning the CCD" to drop the
mirror back down.
Cleaning the CCD:
1. Perform steps 1 to 5 in "Determine whether cleaning is
required" to swing the mirror up.
* Never disconnect the AC adapter while cleaning the CCD.
Damage to the camera shutter may result!
2. Use a blower to remove any dust on the CCD surface.
Please note when cleaning the CCD:
* Use a blower that does not have an attached brush.
Using a blower brush to clean dust from the CCD can
scratch the CCD surface.
3. Unwrap a Sensor Swab™and moisten both sides with a
few drops of Eclipse™optic cleaner.
4. Gently wipe using one side of the moistened swab,
ONCE ONLY, across the full length of the CCD. Repeat
using the other side of the swab, if necessary.
5. Check that all dust has been removed. Hold down both
the self-timer button and the AE lock button "AE-L" as you
switch the camera off. Disconnect the AC power adapter
from the camera.
* When you switch the camera off, the mirror will drop down
and the shutter closes at the same time. Make sure that
your finger or a Sensor Swab™stick is not caught inside
the camera!
If dust or other minute debris attaches to the surface of
the CCD, depending on the camera setting and subject
type, the particles may appear as spots in the image. If
this occurs, the CCD must be cleaned. The CCD is
located behind the shutter screen.
The surface of the CCD is extremely fragile. A camera
that requires CCD cleaning should be sent to an
authorized Fuji Film service center. Please be aware that
cleaning the CCD is considered a maintenance procedure
and a service fee will be applied. CCD cleaning is NOT
covered by warranty.
Please note that scratched or damaged CCD sensors may
need to be replaced. This will involve a very expensive
procedure. Please be aware that damage to the CCD or
camera caused by an attempt by the customer to clean
the CCD using the procedure described below is not
covered by warranty and that responsibility for any
charges necessary to repair the product rests with the
customer.
Note: How to keep dust off the CCD:
a). Change the lens in an area free from dust.
b). If the lens is removed attach a clean body cap to cover
the mirror box.
c). Check that the body cap and lens are free of dust.
WARNING: In no event will Fuji Film be responsible for
any damage that may result to the camera relating to the
cleaning procedures described herein. See product
warranty for further details.
Determine whether cleaning is required:
1. Connect the AC adapter and load the battery adapter.
* When cleaning the camera, always use the AC power
adapter, AC-5VH, and battery adapter to prevent
damaging the camera. While cleaning the CCD, power
from the AC power adapter keeps the mirror from
dropping and holds the shutter open.
2. Remove the camera lens.
3. Set the exposure mode dial to M.