FujiFilm FinePix S1800 Series User manual

DIGITAL CAMERA
Confidential: FUJIFILM Service Center Use Only
FinePix S1800/
S1850/
S1880/
S1900
SERVICE MANUAL
US/EF/E1/EG/EE/CH-model
Ref.No.: ZM00812-103
Printed in Ja
p
an 2010.03
●THE COMPONENTS IDENTIFIED WITH THE MARK " " ON THE SCHEMATIC DIAGRAM
AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY.
●PLEASE REPLACE ONLY WITH THE COMPONENTS SPECIFIED ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST.
●IF YOU USE PARTS NOT SPECIFIED, IT MAY RESULT IN A FIRE AND AN ELECTRICAL
SHOCK.
●BECAUSE THIS PRODUCTIS RoHS LEAD-FREE COMPLIANT, USE THE DESIGNATED
AFTER-SELES PARTS AND THE DESIGNATED LEAD-FREE SOLDER WHEN
PERFORMING REPAIRS.
FUJIFILM Cor
p
oration

Confidential: FUJIFILM Service Center Use Only
1. Check the area of your repair for unsoldered or poorly 7.
soldered connections. Check the entireboardsurface
forsoldersplasherandbridges.
2. Check the interboard wiring to ensure that no wires
are "pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors,thatwereinstalledduringaprevious
repair.Pointthemouttothecustomerandrecommend
theirreplacement.
4. Look for parts which, though functioning, show
obvious
signs of deterioration. Point them outtothecustomer
and recommend their replacement.
5. Check the B + voltage to see it is at the values
specified. 8.
6. Make leakage - current measurements to determine
that exposed parts are acceptably insulated from
the supply circuit before returning the product to the
customer.
CAUTION: FOR CONTINUED
ATTENTION: AFIN D'ASSURER
UNE PROTECTION
PERMANENTE CONTRE
LES RISQUES D'INCENDIE,
REMPLACER UNIQUEMENT
PAR UN FUSIBLE DE MEME,
TYPE 2.5 AMPERES, 125/250
VOLTS.
RISK OF FIRE-
REPLACEFUSE
A
S MARKED
WARNING:
SHOCK, BE CAREFUL TO
TOUCH THE PARTS.
TO REDUCE THE ELECTRIC
SAME TYPE 2.5 AMPERES
125V/250V FUSE.
PROTECTION AGAINST FIRE
HAZARD, REPLACE ONLY WITH
safety check before return the product to the customer.
SAFETY CHECK-OUT
After correcting the original problem, perform the following
2

RoHS lead-free compliance
Confidential: FUJIFILM Service Center Use Only
With the exception of parts and materials expressly excluded from the RoHS directive, all the internal connections and
component parts and materials used in this product are lead-free compliant under the European RoHS directive (*1). Use the
designated after-sales parts and the designated lead-free solder when performing repairs.
*1: Definition of lead-free
A lead content ratio of 0.1 wt% or less in the applicable locations (solder, terminals, electronic components, etc.)
<Lead-free soldering>
When lead-free solder is used, the solder tends to be less workable than when eutectic solder is used. When carrying out
repairs, use a designated lead-free solder, bearing in mind the differing work practices for eutectic solder and lead-free
solder.
■ Differences in the soldering work for lead-free and eutectic solder
Eutectic solder (Sn-Pb) Lead-freesolder(Sn-Ag-Cu)
Melting point 183°C220°C
Soldering iron temperature 283°C 320°C The bonding temperature that will
give the best bond strength.
Wetting Good Poor
Surface Gloss Matte
■Recommended equipment
Solder type (Displayed symbol)
SnAgCu
Wire diameter 0.8mm
lead-free
■Soldering iron maintenance
Because of the high soldering iron temperature in lead-free soldering, there is rapid carbonization of the flux adhering to
the tip of the soldering iron.
(1) Always cover the tip of the soldering iron with solder when it is not being used.
(2) If the tip is black from carbonization, wipe it gently with a paper towel soaked in alcohol until the solder will wet.
3

1.Disassembly......................................................................1-1 4.Inspection...................................................4-1
REARCOVERASSY..............................................................1-1 4-1.RequiredMeasuringEquipment..........................4-1
BATTERYCOVERASSY....................................................1-2 4-2.ConnectionofMeasuringEquipment...................4-1
LCDHOLDERASSYandLCD:.........................................1-3 4-3.InspectionandFactorySettings..........................4-2
STRAPLEFT&TOPBOARDMYLAR&
WIREFFC&PCBASHUTTERASSY&TOP 5.PartsList....................................................5-1
BOARDASSY&EVFASSY&EVF....................................1-4 5-1.PackingandAccessories.......................5-1
FLASHTCOVERPIB&FLASHHINGE& 5-1-1.FinePixS1800E1-model...............................5-1
FLASHBOTTOMASSY&TOPCOVERCONST:.......1-7 5-1-2.FinePixS1800EF-model...............................5-2
MAINPWBASSY......................................................................1-8 5-1-3.FinePixS1800EE-model...............................5-3
PCBAAFLEDASSY...............................................................1-9 5-1-4.FinePixS1800EG-model...............................5-4
LENSCONST.............................................................................1-10 5-1-5.FinePixS1800US-model...............................5-5
FRONTCOVERASSYB&FRAMEASSY& 5-1-6.FinePixS1850EG-model...............................5-6
CAPMYLAR...............................................................................1-10 5-1-7.FinePixS1880CH-model...............................5-7
5-1-8.FinePixS1900EE-model...............................5-8
2.Schematics...........................................................................2-1 5-1-9.FinePixS1900EG-model...............................5-9
Cautions........................................................................................2-1 5-2.MechanicalBlock.................................5-10
BlockDiagram............................................................................2-2 5-3.Electricalparts...................................................5-11
OverallconnectionDiagram.................................................2-3
MountedPartsDiagrams........................................................2-4 6.Appendix....................................................6-1
MAINPWBASSY.......................................................................2-4 6-1.ListofRelatedTechnicalUpdatesIssued............6-1
3.Adjustments....................................................................3-1
3-1.Importantpointbeforeadjustment.......................3-1
3-1-1.Thehandlingof
imagefilesininternalmemory.......................3-1
3-1-2.Adjustmentwhenreplacingmajorparts...3-2
3-2.Measuringinstrumentsused..................................3-2
3-3.Usejiglist........................................................................3-3
3-4.Calibrationmethodofpatternbox.......................3-3
3-5.PreparationofAdjustmentSoftware..................3-4
3-5-1.Variousdownloading
softwaredecompressions,
preservationmethods,andnotes.................3-5
3-5-2.Compositionof
AdjustmentSoftware,and
CreationofSDCardforAdjustment.......3-6
3-5-3.CreatingafirmwareSDcard...........................3-6
3-5-4.CreatingaLCDAdjustmentSDcard............3-7
3-6.LCDAdjustment.............................................................3-8
3-7.ModuleSelect................................................................3-9
3-8.FirmwareDownload....................................................3-11
3-9.EFAAdjustment...........................................................3-13
3-10.ShutterDelayAdjustment....................................3-14
3-11.ISODBPShadingAdjustment............................3-15
3-12.RunInWBPAdjustment.........................................3-17
3-13OISDATADownload...............................................3-18
3-14.PreparationofFxS1700USBID/
LENSDATAWritingSoftware............................3-19
3-15LENSDATARead.....................................................3-23
3-16.USBID/LENSDATAWriting..............................3-24
3-16-1USBIDWriting......................................................3-24
3-16-2LENSDATAWriting.........................................3-26
3-17.OISCalibration............................................................3-27
3-18.DestinationSetting..................................................3-32
CONTENTS

Confidential: FUJIFILM Service Center Use Only
1.Disassembl
y
REAR COVER ASSY B:
Prerequisites:
[1] Remove:
1. If the memory card or battery inside the camera, please remove it.
To Remove:
[1] Remove the screws(085-0352-001)*7 and (085-0339-001)*4
[3] Take out the REAR COVER ASSY B.
CAUTION: REAR COVER ASS’Y(S/P) includes TAPE LCD WINDOW but do not
include LCD Window. LCD Window is an individual part.
To Install:
[1] Install the REAR COVER A’SSY
[2] Check the REAR COVER whether has been well-fixed
LCD WINDOW
■
★
Postrequisites:
None
★Revised:31, Mar. 2010
■Revised:05, Jan. 2010
1-1

Confidential: FUJIFILM Service Center Use Only
1.Disassembl
y
BATTERY COVER ASSY B:
Prerequisites:
[1] Remove:
• REAR COVER ASSY
To Remove:
[1] Take out the BATTERY COVER ASSY.
To Install:
[1] Reverse the steps in the removal procedure
Postrequisites:
None
1-2

Confidential: FUJIFILM Service Center Use Only
1.Disassembl
y
LCD HOLDER ASSY and LCD:
Prerequisites:
[1] Remove:
•REAR COVER ASSY •BATTERY COVER ASSY
To Remove:
[1] Remove the screws *3. (085-0340-001)
[2] Remove the LCD FPC
[3] Separate LCD from LCD HOLDER ASSY.
To Install:
[1] Reverse the steps in the removal procedure.
Postrequisites:
None
1-3

Confidential: FUJIFILM Service Center Use Only
1.Disassembl
y
STRAP LEFT & TOP BOARD MYLAR & WIRE FFC &PCBA
SHUTTER ASSY & TOP BOARD ASSY & EVF ASSY & EVF:
Prerequisites:
[1] Remove:
• REAR COVER ASSY • BATTERY COVER ASSY • LCD HOLDER ASSY & LCD
Warning: Dangerous voltage.
Use a discharger to discharge the power of “big capacitor” to avoid the shock.
To Remove:
[1] Remove the screws *4(085-0340-001), EVF FPC and WIRE FFC.
[2] Take out the STRAP LEFT.
STRAP LEFT
[3] After take out the TOP COVER ASS'Y, discharge the power of “Flash Capacitor”.
1-4

Confidential: FUJIFILM Service Center Use Only
1.Disassembl
y
[4] Take out TOP BOARD MYLAR and WIRE FFC.
[5] Remove the screws *2(085-0343-001), screw *1(085-0340-001) and unsolder soldering
joints.
[6] Take out the PCBA SHUTTER ASSY.
[7] Remove the screw *2(085-0340-001), and unsolder Flash wires.
TOP BOARD
MYLAR WIRE FFC
PCBA,SHUTTER ASSY
[8] Take out the TOP BOARD ASSY
[9] Remove the screws *2(085-0340-001).
TOP BOARD ASSY
[10] Take out the EVF ASSY
Caution：Push the two hook toward inside direction and take out the EVF ASSY carefully.
Don’t damage the EFA ASSY.
HOOK
1-5

Confidential: FUJIFILM Service Center Use Only
1.Disassembl
y
EVF ASSY
[11] Remove the screws *2(085-0340-001).
[12] Take out the EVF.
To Install:
[1] Reverse the steps in the removal procedure.
[2]The aligned points for assemble TOP BOARD MYLAR on the TOP BOARD ASSY.
Attention：Pulling of wiring is the following figure referring.
Postrequisites:
N
one
1-6

Confidential: FUJIFILM Service Center Use Only
1.Disassembl
y
FLASH TCOVER PI B & FLASH HINGE & FLASH BOTTOM
ASSY & TOP COVER CONST:
Prerequisites:
[1] Remove:
• REAR COVER ASSY • BATTERY COVER ASSY • LCD HOLDER ASSY & LCD
To Remove:
[1] Remove the screws *2(085-0340-001).
[2] Take out the FLASH TCOVER PI B.
[3] Remove the FLASH HINGE.
[4] Take out the FLASH BOTTOM ASSY.
[5] Take out the TOP COVER CONST.
To Install:
[1] Reverse the steps in the removal procedure.
FLASH HINGE
Postrequisites:None
1-7

Confidential: FUJIFILM Service Center Use Only
1.Disassembl
y
MAIN PWB ASSY:
Prerequisites:
[1] Remove:
• REAR COVER ASSY • BATTERY COVER ASSY • LCD HOLDER ASSY & LCD
• TOP COVER ASSY
To Remove:
[1]Remove the screws *1(085-0340-001).
[2]Unsolder SPEAKER wires, Microphone wires, AF wires and Battery wire
from Main board.
[3]Remove CCD/FPC, Motor/FPC and Hall sensor FPC.
[4]Take out the MAIN BOARD ASS’Y.
To Install:
[1] Reverse the steps in the removal procedure.
Unsolder AF wire
CCD FPC
Hall sensor FPC
Motor FPC
Unsolder Battery wireScrews*1 (085-0340-001)
Unsolder Speaker wire
Unsolder MIC wire
Postrequisites:
None
1-8

Confidential: FUJIFILM Service Center Use Only
1.Disassembl
y
PCBA AF LED ASSY:
Prerequisites:
[1] Remove:
• REAR COVER ASSY • BATTERY COVER ASSY • LCD HOLDER ASSY & LCD
• TOP COVER ASSY
To Remove:
[1] Remove screw*3 (085-0343-001).
[2] Take out the PCBA AF LED ASSY.
To Install:
[1] Reverse the steps in the removal procedure.
[2] Follow the grooves to assemble the wires of PCBA AF LED ASSY on Main Frame.
Postrequisites:
None
1-9

Confidential: FUJIFILM Service Center Use Only
1.Disassembl
y
LENS CONST:
Prerequisites:
[1] Remove:
• REAR COVER ASSY • BATTERY COVER ASSY • LCD HOLDER ASSY & LCD
• TOP COVER ASSY •MAIN PWB ASSY_1
To Remove:
[1] Remove screw*4 (085-0341-001).
[2] Take out the LENS CONST.
To Install:
[1] Reverse the steps in the removal procedure.
Postrequisites:
None
1-10

Confidential: FUJIFILM Service Center Use Only
1.Disassembl
y
FRONT COVER ASSY B& FRAME ASSY & CAP MYLAR
Prerequisites:
[1] Remove:
• REAR COVER ASSY • BATTERY COVER ASSY • LCD HOLDER ASSY & LCD
• TOP COVER ASSY •MAIN PWB ASSY_1 • LENS CONST
To Remove:
[1] Remove the CAP MYLAR.
[2] Remove the screw*5(085-0340-001).
[3] Take out the FRAME ASSY, FRONT COVER ASSY B and MICROPHONE.
CAP MYLAR
Screws*5 (085-0340-001)
FRAME ASS’Y
FRONT COVER ASSY B
SIDE DOOR is included in
FRAME ASSY
MICROPHON
1-11

Confidential: FUJIFILM Service Center Use Only
1.Disassembl
y
To Install:
[1] Reverse the steps in the removal procedure.
[2]The aligned points for assemble CAP MYLAR on the FRAME ASSY.
[3] Follow the grooves to assemble the wires of Microphone on Main Frame.
Postrequisites:
None
1-12

Confidential: FUJIFILM Service Center Use Only
2.Scematics
■2. Scematics
2-1. Cautions
<Cautions when replacing parts>
• Do not reuse removed parts. Always use new parts.
• Note that the negative side of tantalum condensers is readily damaged by heat.
• Except for chemical condensers and tantalum condensers, voltage is not displayed on condensers with a voltage
resistance of 50V or less.
• Resistors not marked are 1/16W chip resistors.
• KΩ= 1000Ω, MΩ= 1000KΩ
■Revised:05, Jan. 2010
2-1

Confidential: FUJIFILM Service Center Use Only
2. Schematics
2-2

Confidential: FUJIFILM Service Center Use Only
2. Schematics
2-3

Confidential: FUJIFILM Service Center Use Only
2. Schematics
2-4