FujiFilm Instax Square SQ 6 User manual

EN
FR
HU
TW
PT
IT
DE
ES
KO
RU
NL
PL
CS
SK
CPL11B704-201
User’s Guide/Trouble shooting/Safety precautions
Bedienungsanleitung/Fehlerbehebung/Sicherheitsmaßnahmen
Guide d’utilisation/Guide de dépannage/Précautions de sécurité
Manual de instrucciones/Solución de problemas/Precauciones de seguridad
使用說明書/現象、可能的原因及解決措施/安全注意事項
사용설명서/문제 해결/안전을 위한 주의사항
Manual de Utilização/Resolução de problemas/Precauções de segurança
Руководство пользователя/устранение неполадок/меры предосторожности
Guida per l’Utente/Risoluzione dei problemi/Precauzioni per la sicurezza
Gebruikershandleiding/Probleemoplossing/Veiligheidsmaatregelen
Instrukcja obsługi/Rozwiązywanie problemów/Wskazówki bezpieczeństwa
Uživatelská příručka/Řešení potíží/Bezpečnostní opatření
Používateľská príručka/Riešenie problémov/Bezpečnostné pokyny
Használati útmutató/Hibaelhárítás/Biztonsági óvintézkedések
instax_BO-11_instbook_14Lang.indb 1 2018/2/23 10:47:17

© 2018 FUJIFILM Corporation. All rights reserved.
ENGLISH:
See pages 3 to 24.
DEUTSCH:
Siehe Seiten 25 bis 45.
FRANÇAIS:
Voir pages 47 à 68.
ESPAÑOL:
Consulte las páginas 69 a 89.
中國語:
請參閱第 91 到110 頁。
한국어:
111~130페이지를 참조하십시오.
PORTUGUÊS:
Veja as páginas 131 a 152.
РУССКИЙ:
См. стр. 153 – 174.
ITALIANO:
Vedere le pagine da 175 a 196.
NEDERLANDS:
Zie pagina’s 197 tot 218.
POLSKI:
Patrz strony od 219 do 240.
ČESKY:
Viz strany 241 až 262.
SLOVENČINA:
Pozrite si strany 263 až 284.
MAGYAR:
Lásd: 285–306. oldal.
instaxBO-11instbook14Lang.indb2 2/2/20185:37:57PM

3
EN
Contents
Part Names.............................................................................................................................................................. 4
Attaching the Strap .............................................................................................................................................6
Inserting Batteries................................................................................................................................................ 7
Loading the instax SQUARE Film Pack.......................................................................................................... 8
Turning the Camera on/off.............................................................................................................................10
Taking Pictures ....................................................................................................................................................10
Unloading a Used instax SQUARE Film Pack..............................................................................................................11
Taking Pictures with Various Shooting Modes ........................................................................................12
Selecting a Shooting Mode..............................................................................................................................................12
Taking Pictures without Using the Flash (Flash Suppressing)............................................................................. 12
Shooting Mode..................................................................................................................................................................... 13
Using the Self Timer...........................................................................................................................................15
Using the Flash Filter.........................................................................................................................................15
SPECIFICATIONS..................................................................................................................................................16
TROUBLE SHOOTING.........................................................................................................................................17
IMPORTANT SAFETY NOTICE..........................................................................................................................20
ENGLISH
• Read“IMPORTANT SAFETY NOTICE” (Page 20)
for safety use.
• After reading this User’s Guide, keep it in a safe,
easy to find place where you can refer to it if
needed.
instaxBO-11instbook14Lang.indb3 2/2/20185:37:57PM

4
EN Part Names
Front
1Power switch
2Film ejection slot
3Self timer light
4Viewfinder
5Strap hook
6Shutter button
7AE light sensor window
8Flash sensor window
9Tripod socket (Tripod sold separately)
10 Lens/Lens cover
11 Self-portrait mirror
12 Flash
1
910
2
12
4
7
8
3
5
6
11
instaxBO-11instbook14Lang.indb4 2/2/20185:37:57PM

5
EN
Part Names (Continued)
Rear
13 Mode indicator/LED
14 Strap hook
15 MODE (mode) button
16 Self timer button
17 Flash suppressing button
18 Back cover lock
19 Back cover
20 Film counter
21 Battery lid
22 Film pack confirmation window
23 Viewfinder
18
23
19
14
15
16
17
22
13
20
21
instaxBO-11instbook14Lang.indb5 2/2/20185:37:57PM

6
EN Attaching the Strap
Attach the provided camera strap to the strap hook on each side as in the illustrations below.
Caution
• For safety, use the strap only as a shoulder strap. Do not put the strap around your neck.
• Be careful so that the strap does not obstruct the film ejection slot.
~
Ÿ
instaxBO-11instbook14Lang.indb6 2/2/20185:37:57PM

7
EN
Inserting Batteries
Open the battery lid.
Caution
• Use two new CR2 lithium batteries. (All the batteries should be new and be the same brand/type.)
• Insert the batteries before you load the instax SQUARE film pack.
• The battery performance may be reduced when it is cold. In this case, warm up the batteries to room temperature
before using this camera.
Insert the batteries.
• Insert one CR2
lithium battery
straight (1)
matching the C
and Dpolarities
and slide it to the
end (2).
Then, insert the
other battery.
!~
ŸAlign the tabs on
the battery cover
and push the battery
cover lock until it
clicks into place.
To remove the batteries, remove one battery first, and
then slide the other battery and take it out.
instaxBO-11instbook14Lang.indb7 2/2/20185:37:57PM

8
EN Loading the instax SQUARE Film Pack
Caution
Do not open the back cover until you have used up the film; otherwise, the rest of the film will
become exposed and turn white. The film can no longer be used.
• When you load the film pack, never press the two rectangular holes on the back of the film pack.
• Never use a film pack beyond its shelf life; otherwise, it may damage the camera.
Use FUJIFILM Instant Film “instax SQUARE” only. The instax mini film or instax WIDE film cannot be
used.
Notes on the film pack
• Each FUJIFILM Instant Film“instax SQUARE”pack contains 1 black film protective cover and 10 film sheets.
• Do not remove the film pack from its inner bag before loading it into the camera.
For details, refer to the instructions and warnings on FUJIFILM Instant Film ”instax SQUARE”.
Press the back cover lock down to open the back
cover.
Hold both sides of the film pack, align the yellow
marks on the camera and the film pack, then
insert it straight.
~Ÿ
instaxBO-11instbook14Lang.indb8 2/2/20185:37:58PM

9
EN
Loading the instax SQUARE Film Pack (Continued)
Slide the power switch toward the “ON”side to
turn the camera on.
• Do not hold the lens cover when you are turning
the camera on; otherwise, the lens cover will
not open.
Press the shutter button.
The film cover (black) is ejected and“10
” is displayed
on the film counter on the back of the camera.
Carefully remove the film cover.
Close the back cover. Make sure the back
cover lock clicks into place.
@
!
⁄
instaxBO-11instbook14Lang.indb9 2/2/20185:37:58PM

10
EN Turning the Camera on/off
Slide the power switch toward the “ON” side to turn the
camera on.
The lens will extend and the LED on will light up.
• Do not hold the lens cover when you are turning the
camera on; otherwise, the lens cover will not open.
Slide the power switch toward the “OFF” side to turn the
camera off.
The lens will retract and the LED on the mode indicator
will go off.
Auto power off
When no operation occurs for 5 minutes, LEDs on the back
will go off and the camera will turn off automatically.
Press one of the buttons on the back to turn the camera
on again.
~
Ÿ
!
Taking Pictures
Press the shutter button.
• The shutter will not release while the flash is
charging. (The LED on the flash suppressing
button will be flashing while the flash is charging.)
• Hold the camera with the flash lampface at the
top.
• Be careful so that your fingers or the strap do not
cover the flash lampface, flash sensor window, AE
light sensor window, lens, or film ejection slot.
• Look into the viewfinder so that the“O” mark
appears in the center.
• Be careful not to touch the lens surface when you
press the shutter button.
Slide the power switch toward the “ON” side to turn
the camera on.
Hold the camera and confirm the desired
composition of the final image.
instaxBO-11instbook14Lang.indb10 2/2/20185:37:58PM

11
EN
Taking Pictures (Continued)
⁄Every time you take a photo, the number on the film counter decreases
from“10”to reflect the number of remaining photos, and“0” is displayed
when you have used up the film pack.
When the film has been ejected (the camera stops making a sound), grasp
the edge of the film, then take it out.
• The developing time is approximately 90 seconds. (The time varies
depending on the ambient temperature.)
When finished using the camera, always switch the camera to “ off ” to
maintain battery life. If the camera is left switched
“ on ” for 5 minutes
without being used, it will automatically switch to
“ off ” .
When
“ 0 ” is displayed on the film counter, unload the film pack following the procedure below.
Unloading a Used instax SQUARE Film Pack
~Ÿ
Press the back cover lock down to open
the back cover.
Grasp the rectangular holes on the film pack,
then pull it out straight.
instaxBO-11instbook14Lang.indb11 2/2/20185:37:58PM

12
EN Taking Pictures with Various Shooting Modes
You can choose settings according to the subject or purpose.
Selecting a Shooting Mode
Each time you press the MODE button, the shooting
mode changes as follows.
Press the MODE (mode) button.
The LED on the selected mode lights up.
Auto Landscape
Double exposure
Macro
Lighten
Selfie
Darken
• Taking a photo does not change the settings.
• Turning the power off returns to Auto.
Taking Pictures without Using the Flash (Flash Suppressing)
Select this where using the flash is prohibited or when you want to shoot without the flash in a bright place.
Press the flash suppressing button.
The LED on the flash suppressing button will light up - pressing the shutter button will
not let the flash fire.
Flash suppressing is retained even after pressing the shutter button. To cancel, press
the flash suppressing button.
• Depending on the lighting conditions, the picture may look bluish-green, reddish,
or darker or lighter than expected.
• Use of a tripod is recommended in dark lighting conditions.
instaxBO-11instbook14Lang.indb12 2/2/20185:37:59PM

13
EN
~Ÿ
Taking Pictures with Various Shooting Modes (Continued)
Shooting Mode
You can take a self portrait using the self portrait mirror. Using this mode applies an appropriate brightness and
shooting distance for self portrait.
Hold the camera securely
keeping 30 cm to 50 cm between
you and the edge of the lens.
• Hold the camera securely
especially in a dark place, to
prevent blurring.
Confirm the
composition using the
self-portrait mirror, then
take a photo.
Selfie
• When you take a photo, do not look at the flash; otherwise, an afterglow may interfere with your view temporarily.
• If you press the shutter button while the flash is charging, the shutter release will not trip.
• In a dark place, the slow shutter may automatically be used. Hold the camera securely to prevent camera shake.
• The background may look bluish-green or reddish depending on the lighting condition.
Select for normal photography.
• As the flash fires with slow shutter (slow synchro) in a dark place, the background is photographed brightly.
Auto
instaxBO-11instbook14Lang.indb13 2/2/20185:37:59PM

14
EN Taking Pictures with Various Shooting Modes (Continued)
Shooting Mode (Continued)
Macro
Select when shooting a subject at close range (30-50 cm).
• Hold the camera so that the “ O ” mark in the viewfinder
is on the upper right of the center of the subject (see
the illustration above), then take a photo.
Select when shooting a distant subject (2 m〜∞).
Landscape
Double exposure
2 separate subjects are photographed in one picture.
When you shoot the first subject, the LED on will flash.
After the LED has flashed, shoot the second subject.
Select to lighten the picture if photos are coming out too
dark.
Lighten
Select to darken the picture if photos are coming out too
bright.
Darken
instaxBO-11instbook14Lang.indb14 2/2/20185:37:59PM

15
EN
Using the Self Timer
~Ÿ
Press the self timer button once.
The LED on the self timer button
lights up. If you press the shutter button, the self timer lamp is lit about 7
seconds. After that, the lamp flashes about 3 seconds and the
shutter is released.
※To cancel the self timer, press the self timer button while the
self timer lamp is lit or flashing.
Lit about 7 seconds Flashes about 3 seconds
You can use the self timer in combination with each shooting mode.
Using the Flash Filter
Using the flash filter allows you to take a picture which may look different than usual.
[Important] When you take a picture in a dark place
If you take a picture using the flash filter, the picture may look darker than
expected. Select for the shooting mode when you use the flash filter in a dark
place such as indoors and want the picture to look brighter.
instaxBO-11instbook14Lang.indb15 2/2/20185:38:00PM

16
EN SPECIFICATIONS
Film FUJIFILM Instant Film “instax SQUARE” (Purchased separately)
Picture Size 62 mm x 62 mm
Lens Retractable lens, 2 components, 2 elements, f = 65.75 mm, 1:12.6
Viewfinder Inverted Galilean finder, 0.4 x, with target spot
Focusing Motor-driven 3-range switching (0.3 m - 0.5 m, 0.5 m - 2 m, 2 m and beyond),
Macro Mode (0.3 m - 0.5 m) Normal Mode (0.5 m - 2 m) Landscape Mode (2 m and
beyond)
Shutter Release Programmed electronic shutter release, 1.6 sec - 1/400 sec.
Exposure Control Automatic, Interlocking range (ISO 800) : LV 5 - LV 15.5,
Exposure compensation:±2/3 EV
Film Feeding Out Automatic
Film Developing Time Approximately 90 seconds (Varies depending on the ambient temperature)
Flash In Macro mode: Built-in, automatic electronic flash
In a mode other than Macro mode: Always flashing
Charging time: 0.2 sec - 7 sec (using a new battery), Flash charging indicator, Effec-
tive flash lamp range: 0.3 m - 2.7 m
Self-Timer Electronically controlled, approx. 10 second delay, Can be stopped mid-run
LED Display
Shooting mode (Auto, Selfie, Macro, Landscape, Double exposure), Brightness adjust-
ment, Flash suppressing, Self timer Mode
Power Supply Two CR2/DL CR2 lithium batteries
Capacity: Approximately 30 instax SQUARE 10-pack film packs with new CR2/DL CR2
lithium batteries
Others Film pack confirmation window, tripod socket (tripod sold separately)
Dimensions & Weight 118.7 mm x 128.1 mm x 58.1 mm (not including protrusions)/ 393g (without bat-
tery, strap, and film pack)
Accessories Two CR2/DL CR2 lithium batteries, Shoulder strap, Three flash filters
*Specifications are subject to change for improvement.
*Certification marks acquired by the camera are located on the back of the back cover.
instaxBO-11instbook14Lang.indb16 2/2/20185:38:00PM

17
EN
TROUBLE SHOOTING
★When to replace the batteries
1When the lens does not work when the power is switched on.
2When it takes an unusually long amount of time for the flash to be charged.
3When pressing the shutter button turns off the camera.
* Replace both CR2 batteries with new lithium batteries of the same brand/type.
TROUBLE SHOOTING
During operation
Problems Possible Causes Solutions
The shutter release
won’t trip.
1The battery power is low.
2The LED on the flash suppressing
button or the self timer lamp is flashing
rapidly.
3The film counter is showing“0” sign.
1Replace both batteries with new batteries.
2The flash is charging. Please wait until the LED
or lamp turns off.
3Unload the film pack, and load a new film
pack.
The LED(s) on the
mode indicator is
flashing.
●The camera has some trouble. 1Remove the batteries and reinsert them with
the LED flashing.
2If 1does not resolve the problem, contact a
FUJIFILM authorized distributor.
The film pack won’t
load into your
camera, or won’t load
into your camera
smoothly.
1The film pack is not for your camera.
2You are not loading the film pack
correctly.
1Use FUJIFILM Instant Film“instax SQUARE”
only. (No other films can be used.)
2Match the yellow line on the film pack with
the yellow positioning mark in your camera.
Follow the FUJIFILM Instant Film“instax
SQUARE” instructions.
The film cover cannot
be ejected.
●The battery power is low. ●Replace both batteries with new batteries and
load the film pack again.
instaxBO-11instbook14Lang.indb17 2/2/20185:38:00PM

18
EN Problems Possible Causes Solutions
The film cannot be
ejected.
1The camera shakes or has been
dropped and the film is misaligned.
2
The film has been jammed.
1Load a new film pack.
2Remove both batteries and insert them again.
If this does not solve the problem, remove
the jammed film and load a new film pack.
The battery becomes
exhausted quickly.
●The batteries are not the same type. ●Replace both batteries with new CR2 lithium
batteries of the same brand/type.
Printed pictures
Problems Possible Causes Solutions
Part or whole finished
print is white.
●The back cover was opened before you
have used up the film.
●Do not open the back cover until you have
used up the film; otherwise, the rest of the film
may be exposed and ruined for use.
The finished print
looks over exposed.
(White in color)
1The ambient temperature is low (below
+5°C).
2The AE light sensor window or flash
sensor window was covered.
1Before taking pictures, place your camera in a
warm place to bring it to room temperature.
2Be careful not to block the AE light sensor or
flash sensor window, or so that nothing blocks
it.
The finished print
looks under exposed.
(Dark)
1The ambient temperature is high
(above +40°C).
2The picture was taken facing the light.
3The flash lampface, AE light sensor
window or flash sensor window was
covered.
4
The background is too bright in
comparison with the subject.
5The flash light did not reach the
subject.
6The flash light reflected back from a
mirror or window glass.
1Keep camera, film (exposed prints) away from
excessive heat (+40°C).
2Take pictures with the light behind you.
3Be careful not to cover the flash lampface, AE
light sensor window, or flash sensor window.
4SELECT “ ”for the shooting mode.
5Take pictures closer than 2.7 m from the
subject.
6Take pictures at an angle not facing the mirror
or window glass.
instaxBO-11instbook14Lang.indb18 2/2/20185:38:00PM

19
EN
Problems Possible Causes Solutions
The picture is out of
focus.
1The shooting distance is not
appropriate.
2The lens is not clean.
3Your camera was shaken when taking
the picture.
1Select the shooting mode according to the
distance.
2Clean the lens.
3Hold your camera firmly and press in the
shutter release button gently. Since the slow
shutter is selected when shooting indoors or
dark outdoors, stabilizing the camera using a
table, tripod, etc. is recommended.
The picture is blurred. 1Picture was not permitted to develop
without touching, pressure being
applied or other interference once it
ejected from the camera.
2The picture did not come out smoothly.
1Do not press onto or fold the picture.
2Do not block the film exit with your finger.
The subject in the
viewfinder has shifted
in finished print.
●The shooting distance is too close to
the subject.
●See notes on using Macro Mode.
The subject seen
from the viewfinder
is not included in the
picture.
●The view into the viewfinder may have
been at an angle when the picture was
taken.
●Look straight into the viewfinder when taking
a picture.
instaxBO-11instbook14Lang.indb19 2/2/20185:38:00PM

20
EN IMPORTANT SAFETY NOTICE
This product has been designed with safety in mind, and to provide safe service when handled correctly and in ac-
cordance with the User’s Guide and instructions. It is important that both the product and the INSTAX film are handled
properly and used only to take pictures as instructed in this User’s Guide and in the instax SQUARE film instructions. For
your ease and safety, please follow what is written in this User’s Guide. It is also a good idea to keep this User’s Guide in a
safe, easy to find place where you can refer to it if needed.
WARNING
This symbol indicates danger, which could result in injury or death. Please follow these instructions.
WARNING
Never attempt to take this product apart. There is a danger of an electric shock.
If this product is dropped or damaged so that the inside is showing, do not touch it. There is danger of an
electric shock.
If the camera or the batteries inside become hot, begin to smoke, make a burning smell or show any sign
of unusual condition, remove the batteries right away. Use gloves to keep from burning your hands. Not
removing batteries could result in burns or fire.
Using a flash too close to a person’s eyes may for the short term affect the eyesight. Take care when taking
picture of infants and young children.
If your camera gets wet or if something such as pieces of metal get inside, remove the batteries right away to
avoid heat buildup or a fire starting inside the camera.
Do not use this camera in places where there is flammable gas or near open gasoline, benzene, paint thinner
or other unstable substances which can give off dangerous vapors. Doing so could result in explosion or fire.
Store your camera out of the reach of infants and young children. Failure to do this could result in serious
injury. (For example, the strap could become wrapped around a child’s neck and cause choking.)
Never take apart the batteries. Do not subject them to heat, throw them into an open fire, or attempt to short-
circuit them. Doing so could result in the batteries exploding or splitting open causing burns or fire.
instaxBO-11instbook14Lang.indb20 2/2/20185:38:00PM