Fujioh FZ-WH5033N Manual

Operating / Installation Manual
FZ-WH5033N
FZ-WH5033NR
FZ-WH5033D
FZ-WH5033DR
Please read this manual carefully
before using this appliance.

21 - 22

Fujioh
Fujioh

1 x Hand shower
c/w filter mesh washer
& flow restrictor
1 x Fujioh Heater Unit
1 x Sliding Rail Set
2 x Wall Plug & Screw Set
(1 spare)
Hand

1 x Fujioh Heater Unit
1 x Spout
1 x Hand shower
c/w filter mesh washer
& flow restrictor
(1 spare)
+ allen key

7
9
10
5
6
8
4
3
Soap Dish

Spout

13
11
DC Pump Model
Indicator
14. LVDC Board
15. DC Pump Assembly
16. Pump Speed Control
5
15
14
8. Water Tank
None Pump Model
6
7
9.
0
11
12
1
6
7
8
10
1213
7
11
12
10
9
16
1
2
8
6
13
9
2

MOVEABLE
TO HAND SHOWER
Secure Spout to Rain shower(RS) Sliding Rail.
Spout to Rail Support into Fix Plate.
SPOUT
HAND SHOWER
Spout - moveable type
to Spout outlet (BOTTOM: to Hand shower)
outlet of Spout.
Extendable
height 440mm
Open/ closed
(adjust height) + allen key
683
3
3
Tighten with
allen key
Spout inlet (BOTTOM: from Heater outlet)
Be sure do this before step 6, avoid hose colliding
to the wall after spout is installed to wall.
HAND SHOWER
r
h
s
s

3.8

Service
Stop Valve
system

FILTER
CLOSE
OPEN
PLUMBING CONNECTIONS
COMPLETE THIS PROCESS BEFORE WIRING
CONNECTION
CONNECTION PROCEDURE:
Connect the water supply to the inlet of the shower
via 15mm copper, stainless steel or plastic pipe using
a 15mm x 15mm elbow compression fitting.
Do not use excessive force when making these
connections.
FITTING THE STOP VALVE
Fit the Stop valve (Warning: Conductive Valve shall not
be used) by secure to the unit Inlet.
Note:
It is compulsory to have the product installed with
stop valve (with filter) provided, failing which, dirt
particles may cause failure of flow switch assembly.
Ensure the supplied washers are in place before
connecting inlet and the Stop Valve.
Fit the other point of Stop Valve to the incoming water
supply.
Ensure that the backplate of the unit is flat on the wall
and positioned squarely. Tighten the fixing screws.
Turn on the water supply and check for leaks in the
pipework connection to the shower.
NOTE: At this stage no electricity can flow through the
unit.
ELECTRICAL CONNECTION
WARNING: THIS UNIT MUST BE EARTHED.
SWITCH OFF THE ELECTRICITY SUPPLY.
The cable entry points are shown in the figure below.
Determine the cable entry to the unit.
a) Side entry – Poke the electrical cable through
the Rubber grommet.
Route the cable into the shower unit and connect to the
terminal block (Fig. 1) as follows:-
Earth cable to terminal marked ‘ ’
Neutral cable to terminal marked ‘ N ’
Live cable to terminal marked ‘ L ’
IMPORTANT: Fully tighten the terminal block screws
and ensure that no cable insulation is trapped under
the screws. Loose connections can result in cabling
overheating. DO NOT switch on the electricity
supply until the cover has been fitted.

Filter Mesh Washer
Fit the Flexible hose (Warning: Metalic /
Chromed Hose shall not be used) by
connecting to the unit Outlet (Left side)
and hand shower. (Please, make sure to
remove one washer from the end of the
flexible hose connecting to the hand shower.)
Hence, ensure that the supplied washer is in
place at the outlet while, filter mesh and
Flow Restrictor are secured at the hand shower.
& flow restrictor

The ‘MAINS’ Sign will light meaning
the unit is ON.
‘HEATER’ Sign will light up.
‘HEATER’ Sign will switch OFF.

DC