Fujitsu FMWT-401 User manual

This getting started guide contains information
on using your BluetoothTM Modem Station hard-
ware and software with a Bluetooth PC Card. We
strongly recommend that you read this guide
before using the device, even if you are already
familiar with Bluetooth technology and personal
computers.
INSTRUCTIONS
Bluetooth™ Modem Station
Getting Started Guide
Fujitsu PC Corporation

2
Special Notices
Electrical Information
The Fujitsu Modem Station could malfunction in the event
of a change in voltage due to electrical disturbance. To
protect against voltage sag, use of an uninterruptible power
supply (UPS) is recommended.
The frequency band used for the Modem Station is the same
as for some types of industrial, scientific, and medical
equipment, including microwave ovens, as well as on-
premises radio stations (subject to a license) for identifica-
tion of mobile units, e.g., radio stations installed in produc-
tion lines in factories, and other application-specific low-
output radio stations (not subject to a license).
In the event the Modem Station causes radio interference to
an on-premises radio station for identification of mobile
units, immediately change the frequency used or break off
connection, and consult FM Information Service about
preventive measures against radio interference (for example,
installation of partitions).
If you have a problem with the Modem Station, such as
radio interference to an application-specific low-output
radio station for identification of mobile units, contact FM
Information Service for help.
Safety Instructions
This section provides information that you must follow to
avoid personal injury or damage to property when using the

3
Modem Station. Before reading this guide, read the
following information thoroughly.
■Do not install the Modem Station near medical elec-
tronic equipment.
■Don’t use the Modem Station near an automatic door or
fire alarm, otherwise radio waves transmitted by the
Modem Station could affect its automatic control unit.
■Do not insert or pull out the AC adapter with a wet
hand.
■Insert the AC adapter firmly as far as it will go. If not,
this may cause an electric shock or a fire due to heat
generation.
■Pull out the AC adapter immediately when you find any
abnormality. Do not use the Modem Station in the
abnormal conditions, e.g., the unit is damaged, a foreign
smell is given off, a foreign substance is put in the unit,
smoke is emitted, or the unit is heated excessively. This
may cause a fire or electric shock.
■Do not cover or enclose the AC adapter in use. The
accumulated heat may cause a fire.
■Do not exceed the rating of a wall outlet or wiring acces-
sories or use voltages other than 100 VAC.
■If you do not use the AC adapter for a long time, pull
out the plug.
■Never disassemble, repair, or modify the unit. Touching
internal components could cause you to get an electric
shock.

4
Do not leave the unit in the following places:
■Where it is subject to excessive moisture, dust, heat, or
cold
■On an unstable surface
■Where it is subject to mechanical shock
During communication
■You can call up or be called up on the telephone
connected to the Modem Station irrespective of whether
the power to the personal computer or the Modem
Station is turned on or off. The telephone also functions
as a message phone. However, it cannot be used during
communication using the Modem Station.
■When multiple computers have been registered in one
Modem Station, only one personal computer can be
used at a time for communications.
■When a communications application can not be termi-
nated normally, confirm that the status indicator lamps
(“OFF HOOK”and “CONNECT”) of the Modem
Station go off. If they do not go off, turn off the power
switch once and turn it on again. (Telephone charges
will accrue if the “OFF HOOK”and “CONNECT”
lamps remain lit.)
■Avoid using the unit for extended periods of time.

5
This chapter describes basic matters that you should fully
understand before performing communications using the
Modem Station.
Before proceeding, be sure to carefully review the important
safety information starting on page page 2.
Verification of Connector Type
Before connecting the Modem Station, verify the connector
to which you will connect is one of the types shown below.
Figure 1. Jack Configurations
Modular Jack Rosette
3-Terminal Jack 4-Terminal Jack
Getting Started

6
Make a change as described below when the line branch
point used is other than a modular jack.
- For rosette
Replace the line branch point with a modular jack.
- For three- or four-terminal jack
Replace the line branch point with a modular jack or use a
commercial conversion adapter for connection with a
modular plug as shown below.
Figure 2. Conversion Adapter
Using the Modem Station in conjunction with a Bluetooth
PC Card, you can browse Web pages or send and receive e-
mail by connecting wirelessly to the Internet. You can also
send or receive faxes using commercial fax software.
Using the Modem Station

7
Wireless communications can be performed via an analog
line when a Bluetooth PC Card is used together with the
Modem Station.
Figure 3. Connecting with an Analog line
Analog Line
Modem
Station
Computer containing
Bluetooth Card
Wireless
Communication

8
Items included with the Modem Station
Make sure all the following items are contained in the
package. If any item is missing or damaged, contact your
reseller immediately.
Figure 4. Contents of Modem Station Package
Modem Station AC Adapter
Serial Cable Modem Setup Tool Disk
Warranty Card Modular Cable
Mounting Screws User’s Guide Network List

9
Names and functions of the parts
Figure 5. Fujitsu Modem Station
Status indicator lamps
Note that all lamps blink for a few seconds when the power
is turned first on.
POWER: Lights while power to this unit is on.
OFF HOOK: Lights from the time that you start the connec-
tion (you begin to call up a provider) until you disconnect
the line.
CONNECT: Lights from the time you call up a provider
until you disconnect the line (while you are connecting the
Status Indicators
Power Switch
DC Input
Line Input
Telephone
Terminal
Serial Connector
Antenna
(internal)
(for future
use only)

10
line). (TBD - Lit while the phone is connecting until it is
connected, or until it is disconnected?)
LINK: Lights while the unit is connected with a personal
computer.
Switches and Ports
POWER switch
This switch turns the Modem Station power on or off.
DC IN port
This terminal is connected with the DC plug of the supplied
AC adapter.
LINE terminal
This terminal is connected with a telephone line using a
modular cable.
TEL terminal
This terminal is connected with a telephone set using a
modular cable.
Serial connector
This connector is not currently used; it is provided for future
applications.
Antenna
An internal antenna is provided.

11
Figure 6. Bottom Panel - Location of DIP Switches
DIP switches
Note that all DIP switches are set to OFF at the factory. Prior
to changing DIP switch 3 and 4 positions, be sure to turn off
power to the Modem Station
■Switch 1: Set to ON when you want to deaden a sound
during line connection.
■Switch 2: Set to ON when you want to turn off status
indicator lamps.
■Switch 3: Set to ON when you use a terminal adapter.
■Switch 4: Used for system setting. Usually, set to OFF.
Flow of operation.
1. Install the Modem Station.
Perform the “Installation”procedure on page (TBD)
POINT
Steps 1 through 3 below should be executed only the first
time you operate the Modem Station.
OFF
ON
SET UP

12
2. Install the software.
■Install the driver and utility software on your computer
to use the Bluetooth function with the module and PC
card. (Refer to the Bluetooth PC Card manual.
■Install Bluetooth Modem Setup Tool in accordance with
“Installing Bluetooth Modem Setup Tool”on page TBD
3.) Set up the operating environment
■1. Turn on the power of the Modem Station in accor-
dance with “Turning on the power”on page TBD
■Set the operating environment for a Bluetooth module/
PC card at the communication destination. For more
information, see the Bluetooth PC Card manual.
■Set up the modem in accordance with “Setting the
modem”on page TBD TBD (-> P. 25)
4. Perform communications
■Turn on the power of the Modem Station in accordance
with “Turning on the power”on page TBD (-> P. 24)
■Insert the Bluetooth PC card into your computer.
■Connect your computer with the Modem Station wire-
lessly by using a Bluetooth Modem Setup Tool. Refer-
ence “Connecting using Bluetooth Modem Setup Tool”
on page TBD TBD(-> P. 28)
■You can browse homepages or send or receive e-mail by
connecting to Internet. It can also send or receive FAX
using commercial FAX software.

13
This chapter explains the preparations required for commu-
nications, such as the installation of the unit or the setting of
communication.
Installation
1. Disconnect the modular cable of your telephone set from
the jack of the telephone line.
Figure 7. Disconnecting the Modular Cable
2. Connect a telephone set, telephone line, and AC adapter
(Figure 8).
■Connect the disconnected modular cable to the TEL
terminal.
■Connect the LINE terminal and the jack of a telephone
line using the supplied modular cable.
■Connect the AC adapter.
Preparing for Communications

14
Figure 8. Connecting an Analog Line
3. Place the Modem Station vertically in a stable place. Note
that the Modem Station can also be mounted on the wall.
For more information, see “Mounting on the Wall”(-> P.
45).
POINT
The Modem Station can also be mounted to the wall. For
more information, see “Mounting on the Wall” on page
TBD TBD

15
To carry out communications
The Modem Station may not function properly in some
environments. To ensure proper functioning, consider the
following when installing your computer and Modem
Station.
■Install your computer at a line-of-sight distance of
approximately 160 feet (50m) or less fromthe Modem
Station. The communication distance shortens
depending on the use environment (e.g., presence of
walls or furniture) and the structure of the building.
■Install your computer and Modem Station at least 6.5
feet (2m) away from other electric or electronic systems.
(When you need to install your computer or Modem
Station near a microwave oven for some reason, keep it
at least 10 feet (3m) away from the microwave oven.)
Be sure to place the Modem Station in the vertical direc-
tion. If not, the internal antenna will not function prop-
erly.
■If you have trouble communicating using the Modem
Station because there is a broadcast station or radio
equipment nearby, move the Modem Station to another
place. The presence of strong radio waves may impair
proper communication.
POINT
The AC adapter consumes power when it is only connected
to the wall outlet. Pull out the AC adapter from the outlet
when it is not required.

16
Installing the Bluetooth Modem Setup Tool
Install the Bluetooth Modem Setup Tool using a Bluetooth
module or a personal computer in which a Bluetooth PC
card is installed.
1. Turn on power to your computer.
2. After Windows starts, insert the Bluetooth Modem
Setup Tool floppy disk into the computer.
3. Click the [Start] button and then click [Run].
4. Enter “a:\setup”and click the [OK] button. (Change the
drive of the floppy disk as required.)
5. Click the [Next] button.
6. Confirm the directory in which the tool is installed.
Change the directory if necessary and click the [Next]
button.
7. Enter each item and click the [Next] button.
■Enter the device address using half-size numeric charac-
ters. Delimit them two digits at a time by half-size
colons (:).
POINT
Bluetooth PC Utility must be installed before installing the
Modem Setup Tool.
POINT
If the Bluetooth Modem Setup Tool has already been
installed, it will be uninstalled when you execute “setup”.

17
■Enter the Bluetooth passkey (PIN code) using half-size
alphanumeric characters. The entered Bluetooth passkey
(PIN code) is displayed.
■Enter the local device name if it is blank.
■Click the [Next] button.
8. Click “Restart computer”and take out the Bluetooth
Modem Setup Tool floppy disk. Click the [End] button.
9. After Windows restarts, re-insert the Bluetooth Modem
Setup Tool floppy disk into the personal computer.
10. Click the [Start] button and then click [Settings] and
[Control panel].
11. Click [Modem], then click [Add].
13. Click “Not detect to select modem from list”for
checking (@) and then click the [Next] button.
14. Click [Have Disk].
15. Confirm that “Copy source of source file”is (A:\), then
click the [OK] button. (Change the drive name of the
floppy disk, according to your personal computer used.)
16. Click “FUJITSU FMWT-401”, then click the [Next]
button.
17. Click “Bluetooth Virtual COM Port (COM3)”,then
click the [Next] button.
POINT
The device address and Bluetooth passkey (PIN code) are
described on the seal on the left side panel of the Modem
Station.

18
18. Click the [End] button.
19. Take out the floppy disk of the Bluetooth Modem Setup
Tool from the personal computer.
The installation of the Bluetooth Modem Setup Tool is now
complete.
Tur ning on the power
1. Push the power switch on the rear panel in the direction
indicated by the arrow in (Figure 9).
When the power is turned on, all status indicator lamps
blink for a few seconds and then the POWER lamp
lights green.
Figure 9. Turning on power
POINT
Depending on the setting of your personal computer, COM3
may change to COM1 or COM2.

19
Tur ning off the power
1. Push the power switch on the rear panel in the direction
indicated by the arrow in (Figure 10).
When the power is turned off, all status indicator lamps go
off.
Figure 10. Turning off power
Setting the modem
Change the modem, which browser, mail software, and FAX
software use, to “FUJITSU FMWT-401”using your personal
computer. This modem is displayed when Bluetooth
Modem Setup Tool is installed properly. If this modem is
not displayed, execute “Installing the Bluetooth Modem
Setup Tool”(-> P.19). The operation or screen varies
depending on the application used.
POINT
If power is turned off during communication, an error
message may be displayed on the screen.

20
This chapter explains how to establish communications
using Bluetooth.
Connecting using Bluetooth Modem Setup Tool
Connect a personal computer and Modem Station using
Bluetooth Modem Setup Tool.
1. Turn on the power of your computer.
2. Confirm that the power of the Modem Station is on.
3. If you use a Bluetooth PC card, start Windows and
insert the Bluetooth PC card into the personal
computer.
For the way to insert the PC card, see the manual of the
personal computer.
4. Click the “Bluetooth Modem Setup Tool”icon in a task
tray.
POINTS
•If the “Bluetooth Modem Setup Tool”icon is not dis-
played in a task tray, click the “Start”button, “Pro-
gram”, “FUJITSU Bluetooth PC Utility”, and “FUJITSU
Bluetooth Modem Setup Tool”.
•Another way to perform the same operation is to right-
click the “Bluetooth Modem Setup Tool”icon in a task
tray, then click “Connect modem”from the displayed
menu.
Performing Communications