Furious FPV PIGGY OSD FOR KISS FC User manual

Please contact us if you need further assistance:
Tech support: [e-mail]
Sales support: [e-mail]
Website: http://furiousfpv.com/
PIGGY OSD FOR KISS FC
USER MANUAL

Specifications:
Item name: Piggy v2
Power input: 5V
WxLxH : 23.5 x 23.5 x 2.5 mm
Super light weight: 1.1 gr
New chip use low power consumption and
work better
Compatible with all flight controllers that run
KISS
New design layout can fit with most of FPV
Cam such as:
Runcam Swift
Runcam Swift 2
Runcam Eagle
Runcam Rotor Riot
Runcam Owl Plus
Foxeer HS1177
Foxeer Night Wolf
Foxeer Arrow
Foxeer Monster
Other camera:
Lumenier CM-650 Mini –650 TVL Camera
TBS Zerozero V2

Diagram illustrates connections of Piggy V2 with KISS FC
*Note: You need Piggy OSD for KISS FC version or you can flash firmware Piggy V2 BetaFlight to
Kiss FC with FTDI
Using VTX Tramp HV
Using VTX TBS Unify Pro

Using VTX FX FX799T

How to set up Piggy OSD:
-How to set up OSD with TX:
To access the in-built OSD menu in MW-OSD, disarm your quadcopter first.
THROTTLE MIDDLE
YAW RIGHT
PITCH FULL
To navigate through menu in the OSD:
PITCH/ROLL sticks are used to
navigate
YAW stick is used to adjust /
change values
OSD Menu Index:
Voltage (Display voltage on/off, Adjust Voltage, Voltage alarm, Cells)
RSSI (Display RSSI on/off etc)
Current (Display Amp on/off, Adjust Amps)
Advanced (Unit –Metric…)
Display (On/Off switches for Horizon, Sidebars, Scrolling bars, Throttle, GPS Coordinates,
Sensors, Gimbal, Map Mode)
Advanced (Unit, VREF, etc.)
Alarms (Distance, altitude, timer …)
Statistics (Fly time, Maximum Distance, Max Altitude, Max Speed, Flying time)

-How to set up Piggy OSD via Furious FPV FTDI
Furious FPV FTDI is compulsory in order to set up Piggy V2
Tool FTDI : https://goo.gl/Th6x25
Step 1: Download Furious FPV FTDI driver and MW-OSD software
*Note: If you use Furious FPV FTDI, you can install the next steps
Download: MW-OSD GUI R1.6
Download driver here: https://goo.gl/N9aZCN
Step2 : You must extract the zip archive into a temporary directory. DO NOT attempt to double-
click or run any of the files until you have extr acted them
Step 3: Open the temporary directory and run the appropriate executable
If you have a 64-bit operating system, you should run pololu-cp2102-setup-x64.exe
If you have a 32-bit operating system, you should run pololu-cp2102-setup-x86.exe

Step 4: Same below picture

Step 5: Right-click My Computer icon and select Manage. Connect FTDI tool to computer via USB
and click Device Manager. In the Ports (COM & LPT) appearances Silicon Labs CP210x USB to
UART Bridge then your installers completed successfully
*Note: If your computer has not java application, You need to follow steps 6–10 for you connect to
your computer
Step 6: Download and run Java application. Then, follow the same below picture

How to set up OSD with MW OSD:
Step 1: Connect Piggy V2 to the computer via FTDI tool
*Note: Remove everything and only use piggy module when you connect to FTDI tool

Step 2: Open the application MW_OSD_GUI
Step 3: Choose the COM port on MWOSD R1.6 to connect your FTDI with the computer and wait
until MWOSD load complete. You can turn on/off functions that you want to show on your
goggles/display. Note: Click Device Manager and choose the correct COM same as in the Ports
(COM & LPT)
*Note: If you want to show current or voltage on the default screen, you turn on Use FC main
voltage and Use FC amperage same below picture:

Step 4: Click Write to write your OSD configuration to Piggy V2
Flash firmware Piggy v2 Betaflight to KISS FC/Raceflight FC and
vice versa.
Firmware: https://goo.gl/pFhp8z
Xloader: https://goo.gl/IKJveN
After installing driver and running Xloader to flash firmware, connect FTDI tool with Piggy v2 as
instructed and select as below:
Step 1: Select Firmware on your computer
Step 2: Select Duemilanove/Nano (ATmega328)
Step 3: Select Com Port with Baudrate 57600
Step 4: Click Upload and wait finish process

Thanks for using our product