Furman Pf-Pro E User manual

PF-PRO E / PF-PRO R E MANUAL

PF-PRO E / PF-PRO R E MANUAL
PF-PRO E FEATURES
• Clear Tone Technology provides Power
Factor correction with 45 amps peak
current reservoir
• SMP+ (Series Multi-Stage Protection Plus)
with Extreme Voltage Shutdown (EVS)
• LiFT (Linear Filtering Technology) with zero
ground contamination
• Four rear panel outlets
• Three year limited warranty
• Front panel meter to display incoming line
voltage ranging from 180 to 256 volts
PF-PRO R E ADDITIONAL
FEATURES
• Compact rack-mountable design
• 10 rear panel outlets plus one convenient
front panel outlet
• BNC connector on the rear panel allows you
to attach any standard (12VAC 0.5 amp)
gooseneck lamp to illuminate the rear of
your rack
INTRODUCTION
Congratulations on your purchase of a
Furman Power Factor Pro (Model PF-Pro E
or PF-Pro R E). Both Power Factor Pro units
feature Furman’s revolutionary Clear Tone
Technology, and Series Multi-Stage Protection
Plus (SMP+) circuit, as well as our exclusive
Linear Filtering Technology (LiFT). Together
these technologies comprise the world’s
rst comprehensive AC power conditioner for
instrument ampliers.
1
Today’s AC power is contaminated. Whether
you play in a stadium, bar, or rehearsal
space, they all have one thing in common:
the AC power is supplied from your local
utility. What’s worse is that the “power factor”
supplied from your building’s AC outlet is
typically poor, thanks to increasingly over
taxed power lines and raised line impedance.
In fact, the quality of AC power has been so
poor for so long, most musicians have no idea
how great their ampliers could really sound.
When the AC power factor is poor, ampliers
sound muddy because their power supplies
can’t deliver when pushed. The scream and
cry from a guitar loses bite and harmonics,
bass guitars lose their punch and weight,
keyboards sound nasally, losing clarity, attack,
and extension.
Furman’s Power Factor Pro units address this
issue - allowing your amplier to sound its best
while protecting it at the same time.
DESCRIPTION
The Power Factor Pro’s “Clear Tone
Technology” actually lowers the AC line
impedance supplied by your wall outlet, while
storing energy for peak current demands. In
fact, there are over 45 amps (peak charge) of
instantaneous current reserve in the Power
Factor Pro. Additionally, “Linear Filtering
Technology” dramatically lowers AC line noise
to unprecedented levels in the critical audio
frequency band. What does this mean? Just
plug in your current-starved amplier, crank
up the volume, and listen to the dynamics,
harmonics, and clarity you’ve been missing!

PF-PRO E / PF-PRO R E MANUAL
Additionally, the Power Factor Pro units are
the most comprehensive power protection
device ever created for the serious musician.
Furman’s Series Multi-Stage Protection Plus
(SMP+) guards your equipment from voltage
spikes that can damage your amplier or other
connected equipment.
Furman’s SMP+ features unparalleled
clamping voltage. While other designs offer
clamping voltages that are well above 450
Vpk, SMP+ clamps at 376 Vpk (266 VAC
RMS) even when tested with multiple 6000Vpk
- 3000 amp surges! And, our pro level over-
voltage auto shutdown circuit assures you will
never see your prized amplier go up in ames
due to a sustained voltage overload.
The PF-Pro E has a generous 7 amp R.M.S.
capacity, a convenient 20 segment AC
voltmeter, a detachable-locking AC cord,
and (4) AC outlets, all contained in a small
convenient, oor standing package. The PF-
Pro R E has the same features except it has
(10) rear outlets and (1) front panel outlet. It
also features a BNC connector on the rear
panel to allow attachment of any standard
gooseneck lamp (such as Furman’s model GN-
I or GN-LED) to illuminate the rear of your rack.
S A F E T Y I N F O R M AT I O N
To obtain best results from your Furman Power
Factor Pro Power Conditioner, please be sure
to read this manual carefully before using.
WA R N I N G: To reduce the risk of electrical
shock, do not expose this equipment to rain
or moisture. Dangerous high voltages are
present inside the enclosure. Do not remove
the covers. Refer servicing to qualied
personnel only. The lightning ash with an
arrowhead symbol, is intended to alert the user
to the presence of un-insulated dangerous
voltage within the product’s enclosure that may
be of sufcient magnitude to constitute a risk of
electric shock.
I M P O R TA N T S A F E T Y
I N S T R U C T I O N S
(Please read prior to installation)
1. Please read and observe all safety and
operating instructions before installing
your Power Factor Pro unit. Retain these
instructions for future reference.
2. Your Power Factor Pro unit should not be
used near water – for example, near a bathtub,
washbowl, kitchen sink, laundry tub, in a wet
basement, near a swimming pool, etc.
3. Do not place your Power Factor Pro unit
near heat sources such as radiators, heat
registers, stoves, or other appliances that
produce heat.
4. The PF-Pro E and PF-Pro R E should only
be connected to a 220 VAC, 10 amp grounded
electrical outlet. Do not defeat the ground or
change polarization of the power plug.
5. Pay particular attention to the condition of
the cords and cables at the plugs. To prevent
risk of re or injury, damaged cords and cables
should be replaced immediately.
6. Clean your Power Factor Pro unit with
a damp cloth only. Do not use solvents or
abrasive cleaners. Never pour liquid on or into
the unit.
2

PF-PRO E / PF-PRO R E MANUAL
7. Your Power Factor Pro unit should be
serviced by qualied service personnel when:
• The power supply cord or the plug has been
frayed or cut.
• Objects have fallen or liquid has spilled into
the unit.
• The unit has been exposed to rain or other
moisture.
• The unit does not appear to operate normally.
• The “Protection OK” indicator is not lit.
• The unit has been dropped, or the enclosure
has been seriously damaged.
8. Your Power Factor Pro unit requires that a
safety ground be present for proper operation.
Any attempt to operate the unit without
a safety ground is considered improper
operation and could invalidate the warranty.
9. Do not attempt to service your Power Factor
Pro unit beyond what is described in this
manual. All other servicing should be referred
to qualied service personnel.
F E A T U R E S
Both Power Factor Pro units have a master
switch for the rear outlets that glows red when
the power is on. The circuit breaker is located
adjacent to the power switch for the PF-Pro
E and on the rear panel for the PF-Pro R E. It
can be quickly and easily reset should the unit
be overloaded. Both models also feature a
detachable 8 foot, 10A heavy-duty power cable.
The Power Factor Pro, offers a 20 segment
LED bar-graph meter that displays incoming
voltage between 180 and 256 volts in 4-volt
increments. The normal range voltages are
indicated in green, with moderately and
extremely high or low voltages in yellow and
red respectively. The voltmeter’s accuracy
is ±4 volts. It can easily be recalibrated, if
necessary.
The PF-Pro R E features a rear rack BNC
socket which will accept any 12 VAC (0.5A)
gooseneck lamp assembly, (such as the
Furman GN-LED or GN-I). Simply slide the
BNC plug over the socket and rotate clockwise
until the connector snaps into the locked
position. The rear rack lamp can be powered
on or off with the rear light power switch
located on the far left of the front panel.
O P E R AT I O N
Multi-Segment LED Voltmeter:
This three-color, 20-LED bar graph is an
accurate, self checking AC voltmeter that
continually measures input voltages. The
meter reads from 180 to 256 volts, in 4
volt steps. The normal range voltages
are indicated in green, with moderate and
extremely high or low voltages in yellow and
red respectively. The voltmeter provides three
special ashing patterns to indicate abnormal
conditions.
(1) On initial turn on, the voltmeter will
scan for smart chip integrity.
(2) If only the single left most (beneath
the 180V mark) LED ashes, the input
voltage is marginally low.
(3) If all of the LEDs on the voltmeter
ash, the input voltage is marginally
high. Power to the Power Factor
Pro’s outlets will remain on unless the
incoming voltage rises above the
3

PF-PRO E / PF-PRO R E MANUAL
Extreme Voltage Shutdown (EVS)
cutoff voltage (280 volts).
The Power Factor Pro’s voltmeter has a basic
accuracy of plus or minus four volts, and
extreme cold or heat may cause an additional
two volts of error.
NOTE: Although the Power Factor correction
will more than compensate for peak current
demands, the Power Factor Pro does not
compensate for sustained high or low line
voltage. If you derive power from generators,
travel internationally, or are in an area prone
to extreme brownouts, you may benet from
the use of one of Furman’s AC Line Voltage
Regulators.
On/Off Rocker Switch:
This 10 amp capacity power switch is
specically designed to stand up to the
enormous high inrush current demands placed
by many instrument ampliers. Additionally, the
semi-transparent rocker lights when switched
to the “ON” position.
Extreme Voltage Shutdown (EVS) Indicator:
This LED is normally off. It monitors a hazard
unfortunately common in the entertainment
industry: wiring faults – for example, accidental
connection to 380 VAC where 240VAC is
expected, or an open neutral from a 208 or
240VAC feed. The Power Factor Pro’s SMP+
circuit senses voltages that are so high that
operation would be impossible and shuts the
power down before damage can occur. Upon
initially applying power to these units, the
Extreme Voltage indicator LED will be lit if the
input voltage is above the extreme voltage
cutoff, and power will not be applied to the
unit’s outlets. If the unit has been operating
with an acceptable input voltage and then that
voltage goes above 280V, it will shut off power
to the outlet and the Extreme Voltage LED will
light.
NOTE: If the mains power is above the high
cutoff voltage and has caused the unit to
remove power from its outlets, it cannot restore
power without the operator manually turning
the unit off, then on again. Avoid turning the
unit back on without checking the source of the
problem rst, and perhaps changing the AC
source.
4
Mains Vltg. Voltage Status Voltmeter Reading Outlets
166-179 Low Marginal The LED beneath the 180V mark flashes ON
180-211 Low Meter Reads in Low Red ON
212-219 Medium Low Meter Reads in Low Yellow ON
220-240 Normal Meter Reads in Green ON
241-248 Medium High Meter Reads in High Yellow ON
249-256 High Meter Reads in High Red ON
257-265 High Marginal All Meter LEDs Flash ON
Above 280 Extreme (Shutdown) Meter off—Extreme Voltage LED illuminates OFF
Multi-Segment LED Voltmeter Readings

PF-PRO E / PF-PRO R E MANUAL
TROUBLE-SHOOTING GUIDE
1.) Symptom: No power to the AC outlets.
Possible Cause: Circuit breaker has
tripped due to excessive load.
Action Needed: Remove one piece of
equipment from the Power Factor Pro unit,
and push the square re-set tab into the circuit
breaker bezel.
2.) Symptom: No power to the AC outlets,
“Protection OK” indicator is not lit.
Possible Cause: Either the AC outlet that
your Power Factor Pro device is connected
to has no AC voltage present, or the unit has
been subjected to a sustained voltage in
excess of 400 volts.
Action Needed: Plug the Power Factor
Pro unit into an AC receptacle where AC
voltage is present. If the problem persists, the
protection circuit may be damaged factory
service may be required.
3.) Symptom: Extreme Voltage indicator lit.
Possible Cause: Input voltage is above
270 - 280 volts, causing power to the unit’s
outlets to be shut down.
Action Needed: Correct the line voltage.
Then turn the unit on. Consider installing a
Furman voltage regulator.
THREE YEAR LIMITED
WARRANTY
Furman Sound, LLC., having its principal
place of business at 1690 Corporate Circle,
Petaluma, CA 94954 (“Manufacturer”) warrants
its PF-Pro E and PF-Pro R E (the “Product”) as
follows:
Manufacturer warrants to the original
Purchaser of the Product that the Product sold
hereunder will be free from defects in material
and workmanship for a period of three years
from the date of purchase. The Purchaser
of the product is allowed fteen days from
the date of purchase to complete warranty
registration by mail or on-line at the Furman
web site. If the Product does not conform
to this Limited Warranty during the warranty
period (as herein above specied), Purchaser
shall notify Manufacturer in writing of the
claimed defects. If the defects are of such type
and nature as to be covered by this warranty,
Manufacturer shall authorize Purchaser to
return the Product to the Furman factory
or to an authorized Furman repair location.
Warranty claims should be accompanied by a
copy of the original purchase invoice showing
the purchase date; this is not necessary if the
Warranty Registration was completed either via
the mailed in warranty card or on-line website
registration. Shipping charges to the Furman
factory or to an authorized repair location must
be prepaid by the Purchaser of the product.
Manufacturer shall, at its own expense, furnish
a replacement Product or, at Manufacturer’s
option, repair the defective Product. Return
shipping charges back to Purchaser will be
paid by Manufacturer.
THE FOREGOING IS IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED
5

PF-PRO E / PF-PRO R E MANUAL
S E R V I C E
Before returning any equipment for repair,
please be sure that it is adequately packed and
cushioned against damage in shipment, and
that it is insured. We suggest that you save
the original packaging and use it to ship the
product for servicing. Also, please enclose a
note giving your name, address, phone number
and a description of the problem.
NOTE: All equipment being returned for
repair must have a Return Authorization (RA)
Number. To get an RA Number, please call the
Furman Service Department: [phone],
ext. 121. Please display your RA Number
prominently on the front of all packages.
TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. Manufacturer
does not warrant against damages or defects
arising out of improper or abnormal use of
handling of the Product; against defects or
damages arising from improper installation,
against defects in products or components
not manufactured by Manufacturer, or against
damages resulting from such non-Manufacturer
made products or components. This warranty
shall be cancelable by Manufacturer at its
sole discretion if the product is modied in
any way without written authorization from
Furman Sound. This warranty also does not
apply to Products upon which repairs have
been affected or attempted by persons other
than pursuant to written authorization by
Manufacturer.
THIS WARRANTY IS EXCLUSIVE. The sole
and exclusive obligation of Manufacturer shall
be to repair or replace the defective Product
in the manner and for the period provided
above. Manufacturer shall not have any other
obligation with respect to the Products or
any part thereof, whether based on contract,
tort, strict liability or otherwise. Under no
circumstances, whether based on this Limited
Warranty or otherwise, shall Manufacturer be
liable for incidental, special, or consequential
damages. Manufacturer’s employees or
representatives’ ORAL OR OTHER WRITTEN
STATEMENTS DO NOT CONSTITUTE
WARRANTIES, shall not be relied upon by
Purchaser, and are not a part of the contract
for sale or this limited warranty. This Limited
Warranty states the entire obligation of
Manufacturer with respect to the Product. If
any part of this Limited Warranty is determined
to be void or illegal, the remainder shall remain
in full force and effect.
6

PF-PRO E / PF-PRO R E MANUAL
7
Furman Sound, LLC.
1690 Corporate Circle
Petaluma, California 94954-6919 USA
Phone: [phone]
Fax: [phone]
Web: www.furmansound.com
E-mail: [email protected]
030606-C
Important Note:
The Power Factor Pro must be the rst AC power component connected to the AC mains!
Regulators such as the Furman AR-2315 or UPS systems such as the SB-1000 E must be
connected to the Power Factor Pro’s output. This is due to the fact that the PF-Pro’s current
reservoir may hinder the performance of a regulator, and worst case may cause damage in
extreme power environments.
As long as the Power Factor Pro is connected prior to the Regulator or UPS both components
may be used.
SPECIFICATIONS
AC Current Capacity:
Input - 10 Amps capacity required
Output - 7 - 10 Amps RMS (maximum, all outlets
combinted - continuous)*
Operating Voltage:
180 to 280 VAC
Over Voltage Shutdown:
280 VAC typically
Voltmeter Accuracy:
±4 VAC, calibrated with internal trimpot adjustments
Spike Protection Modes:
Line to neutral, zero ground leakage
Spike Clamping Voltage:
376 Vpk (266 VAC RMS)
Response time:
1 nanosecond
Maximum surge current:
6,500 amps
Noise attenuation:
40 dB @ 10 kHz
40 dB @ 100 kHz
100 dB @ 10 MHz
Linear attenuation curve from 0.05 - 100 ohms line
impedance
Transient Current Reservoir:
45 amps peak
Mechanical:
Dimensions:
PF-Pro E: 5.25” H (with feet) x 8.125” W x 12.5” D.
PF-Pro R E: 19 “ W x 11.63” D x 1.75” H
Weight:
PF-Pro E: 11 lbs (5 kg).
PF-Pro R E: 9.7 lbs (4.39 kg)
Power Consumption:
6 watts (resistive)
* (Due to the power factor correction circuit, available RMS power
varies with the reactance of the load (vector). However, this only
affects the circuit breaker for continuous RMS current draw. Since
power ampliers will require high transient current demands, the
Elite-15 PF will never succumb to current compression. Quite the op-
posite, in fact, it will buffer the power amplier’s power supply, while
lowering the AC input impedance, allowing power ampliers to work
more efciently).