FURNITUREBOX SIENA User manual

SIENA TV STAND
ASSEMBLY GUIDE
www.furniturebox.co.uk
Scan QR code for more tips,
advice and assembly video or visit
furniturebox.co.uk/club/siena-tv
SCAN ME

• Check you have all the components and
tools listed.
• Remove all ttings from the plastic bags
and separate them into their groups.
• We do not recommend the use of power
drills/drivers for inserting screws, as this
could damage the unit. Only use hand
screwdrivers and Allen keys.
• Keep children and animals away from the
work area, small parts could cause choking
if swallowed.
• Make sure you have enough space to
layout the parts before starting.
• Assemble the item as close to its nal
position (in the same room) as possible.
• Do not overtighten the nuts to avoid
causing damage to the threads.
Important - Please read these instructions fully before starting assembly
SAFETY AND
CARE ADVICE
!
NO POWER TOOLS
Follow us on Instagram
@furniturebox_uk
• Only clean using a damp
cloth and mild detergent,
do no use bleach or
abrasive cleaners.
• From time to time check
that there are no loose
screws on this unit
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre
SAFETY AND CARE ADVICE

www.furniturebox.co.uk
PLEASE CHECK CAREFULLY AND MAKE SURE YOU HAVE ALL
FITTINGS AND TOOLS LISTED BELOW BEFORE YOU START.
NOTE: The quantities above are the correct amount to complete the assembly. In
some cases more ttings may be supplied than are required.
IMPORTANT INFORMATION
30 MINUTE
BUILD
ONE
PERSON
MAXIMUM
CAPACITY 80Kg
IMPORTANT
STEP

Follow us on Instagram
@furniturebox_uk
STEP 1
Use a clear, at, soft surface to avoid bumps or scratches.
Place top panel [1] face down on your at surface.
Add 2x dowels [D] to the inside holes and 2 x long rod bolts [A] to the outside
holes at the end of bottom panel [1].
Add 1 x rod bolt [A] to the single hole towards the opposite end of panel [1].
Carefully align and drop side panel [2] over the long rods and onto the
dowels at the end of panel [1]. Then add 2 x dowels [D] to the outside holes in
the top of panel [2}.
Add 1 x gasket [C] to the single rod, followed by 1 x tubular support {B] and
another gasket [C].
ATTENTION: Be careful not to over-screw beyond the thread stops.

www.furniturebox.co.uk
STEP 3
Align and carefully drop bottom panel
[4] over the exposed rod ends. Secure
bottom panel [4] into place using 1 x
washer [E] followed by 1 x nut [G] over
each of the three exposed rod ends.
Tighten with spanner [G].
STEP 4
ATTENTION: Check all components
are secured. Carefully, and with help,
turn your TV stand over to it rests on
the bottom panel. Check for stability.
Your TV unit is now ready to use.
FULL ASSEMBLY INSTRUCTIONS
STEP 2
Align middle panel [3] and drop
onto exposed rod ends. Secure
middle panel into place using 1 x
washer [E] followed by 1 x nut [G]
over each of the three exposed rod
ends. Tighten with spanner [G].
Add 2x dowels [D] to the inside
holes and 2 x long rod bolts [A]
to the outside holes at the end of
middle panel [3].
Add 1 x rod bolt [A] to the single
hole towards the opposite end of
bottom panel [1].
Carefully align and drop side panel
[2] over the long rods and onto the
dowels at the end of panel [1]. Then
add 2 x dowels [D] to the outside
holes in the top of panel [2}.
Add 1 x gasket [C] to the single rod,
followed by 1 x tubular support {B]
and another gasket [C]

www.furniturebox.co.uk

The cushions (foam inserts and
covers) are not covered by the guarantee.