Furrion FEHS19E6A User manual

LED HDTV19"
Model: FEHS19E6A
USER’S MANUAL

Warning
To prevent fire and/or electric shock, do not use this plug with an extension
cord, receptacle or other outlet unless the blades can be fully inserted to
prevent blade exposure. Do not expose this appliance to rain or moisture.
Important Safety Instructions
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Please, unplug the TV power cord when the following conditions occur:
-When there is a thunderstorm (Please, pull out the power cord and antenna).
-When cleaning the TV set.
-When the TV set is not used for a long time.
Do not use corrosive depurative when cleaning the TV set.
Do not put the TV set under direct sunlight or near heat.
Do not put a heat source, such as a candle or heater, on top of or near the TV set.
Leave plenty of space (at least 10cm) around the TV set for ventilation.
Place the TV set away from where it can be ruined by rain or water (such as near a
window).
Don't put a container with liquid (such as a vase) on top of the TV set.
Do not move the TV set when the power is on.
Do not touch, push or scratch the surface of the TV set with hard materials or items.
When TV surfaces are dirty, please use a wet cotton cloth or soft cloth with non-
corrosive cleaners to clean it carefully. Don´t use acetone, toluene or alcohol to
clean the TV set.
Be aware and careful of moisture, which can damage inner electronic components.
When condensed moisture is present, the TV screen may appear blurry or spotty.
It is recommended that a technician install the TV set on a wall, if such placement is
desired.
An incorrect wall installation will be unsafe and hazardous.
Do not let children climb on or play around the TV set to avoid falls, collissions,
damages and injuries.
Do not hit the TV panel with hard objects to prevent damages.
Do not cover the TV set with blankets or other objects when it is connected to a
power source to prevent overheating and fire.
Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
Mains plug is used as disconnect device from the mains, the disconnect
device shall remain readily operate.
Apparatus with class I construction shall be connected to a mains socket
outlet with a protective earthing connection.
Safety Information
AVIS RISQUE DE CHOC ELEC TRIOUE/NE PAS OUVRIR

Important Safety PrecautionsImportant Safety Precautions
Do not place the power cord or other cables
across a walkway in case it is trampled on. Do
not overload the power cord or power socket.
When the power plug is used to disconnect and
connect the device, it should easily into the
power source.
Do not place the LED TV on an unstable
surface.
Do not disassemble the back cover, as it
contains high voltages inside and will cause
electric shock. Only qualified professionals
sh o ul d cond uct in t er n al ad j us t me n ts ,
maintenance, and checks.
The TV set should not be subjected to
water droplets, vapor, or splash. This
equipment should not be placed on objects
filled with liquids. Do not place flame
sources, such as lit candles, on or near the
LED TV. Please, pull out the power plug
and contact after sales support if there are
abnormal objects or water in the TV.
Pull out the power cord and antenna cable
during electrical storms so the LED TV is not
damaged by electrical surges. Keep all
people away from the antenna cable during
electrical storms.
Please, immediately pull out the AC power
plug from adapter if there is an abnormal
sound or smell or the LED TV has sound
but no picture, and contact after sales
support.
The LED TV should be kept free from rain,
moisture and dust to prevent electrical
shock and short circuits. Do not cover the
ventilation openings with table clothes,
curtains, newspapers, etc.
The LED TV should be kept from high
temperature heating sources or direct
sunlight. Good ventilation is required.
Allow 10 cm. between the LED TV and
other appliances or built-in cabinet walls.
When you wipe the front cabinet, please
make sure the power plug is pulled out and
use a soft, dry, lint-free cloth and handle it
with care. Do not repeatedly wipe the panel,
nor scrape, tap or strike the panel with a hard
object.
Do not wipe the LED TV with any petrol,
chemical or alcohol based solvents as it
will lead to product damage of the panel
and cabinet.

1
Table of Contents
2
Troubleshooting 18
Introduction
Features
Specifications
2
3
Accessories
General Description
Overview of front and side panel
Overview of back panel
Overview of remote control
Installing Batteries in the Remote Control
4
4-7
4
5
6
7
External Connection
Connecting VCR
Connecting DVD Player/Set-Top Box via HDMI
Connecting PC
10
11
8
PICTURE
AUDIO
14
13
OSD Menu Operations
BASIC OPERATION 13
13
Picture defects and the reason 19
8
Supporting signals
12
TIME
CHANNEL
14
15
W arnings
Features
Introduction
Input terminals used for external equipment connection
One computer VGA/PC inpu t
One AV input
l TV adopts TFT LED display screen
l HDTV Compatible( 480p,720p, 1080i, 1080p)
l Support American TV Standard 8VSB/Free 64/256QAM,NTSC System, ATSC System
l Connect to computer directly to realize TV/monitor combo.
l Zero X radiation complies to green environment protection requirement
l Advanced Chroma Processing
l Closed captioning/PARENTAL LOCK
l SAP/STEREO/MONO; ATSC.
l HDMI input
l USB input (for factory use only)
One ANTENNA jack
One PC Audio input
One HDMI input
One USB for factory use only
SETUP 15
LOCK 16
One L/R output
One Earphone output
Connecting DVD Player/Set-Top Box 9
One Component input
Connecting Amplifier/DVD Home Theater
12

34
Please make sure the following items are included with your LED TV. If any items are
missing, contact your dealer.
Accessories
Remote Control &
Batteries (AAAx 2)
Adapter
Power Cord
Owner’s
Instructions
SPEAKER
REMOTE CONTROL SENSOR
Aim the remote control towards this
spot on the TV.
POWER INDICATOR
Green: In power on mode.
Red: In standby mode.
Toggles between all the available input
CH+/-
Press to change channels.
In the on-screen menu, use the CH +/-
buttons as up/down arrow buttons.
VOL+/-
Press to increase or decrease the volume.
In the on-screen menu, use the VOL +/-
buttons as left/right arrow buttons.
POWER
Press POWER button to toggle between
and standby mode.normal
MENU
Press to see an on-screen menu of your
TV's features.
SOURCE
4 5 67
8
sources ( TV, AV, Component, HDMI,
PC)
Fine digital control
NTSC3.58
75W (Unbalance)
32 W
Color active matrix LED display
NTSC System, ATSC System
Antenna: 2~69; Cable: 1~135 (Analog: 1-125,
Digital: 1-135)
Note:
Introduction
W arnings
Specifications
DC 3V (Two AAA size batteries)
o
0C-40C
o
Design and specification modification maybe made at any time without
prior notice; all data and dimensions are approximations.
Power supply
1366X768
FEHS19E6A
Model
DC 12V 4A
2 x 5 W
General Description
Overview of front and side panel
18.0 x 1.7 x 12.3 inch POWER SO URC E MENU CH-CH+VO L-VO L+
Warranty card
Screws for wall mounting

56
General Description
Overview of back panel Overview of remote control
General Description
1. POWER( ) input
2. HDMI input
3.
4. PC AUDIO
5.
DC 12V
input
input
input
VGA
VIDEO
6. RF input
output
8. YPbPr input
. USB For factory use only
10. output
7. EARPHONE
9
L/R
POWER: Turn the TV on or off.
MUTE: Press to mute the sound, Press again to regain
the sound.
0-9: Press 0-9 to sel et a TV channel directly The channel
will change after 2 seconds. Applicable for entering page
number in teletex t mode and so on.
-/--: Press this button firstly when the channel to be
selected is two or th ree figures (only DVD mode).
RETURN: Return to t he previously viewed program.
P.MODE: Select the picture mode.
S.MODE: Select the sound mode.
SOURCE: Press to select signal source for TV.
VOL+/-: Press these two buttons to increase/decrease the
sound volume.
CH+/-: Press these two buttons to change channels
sequently.
▲▼◀▶/enter: Allows you to navigate the on-screen
menus and adjust the system settings to your
preference.
EXIT: Exit from the menu or sub menu.
MENU: Allow you to na vigate the on-screen menus.
EPG: Press to display EPG (Electronic Program Guide) in
formation.
INFO: Displays the channel in formation.
ZOOM: Press to change the screen scale.
MTS: Press to select the audio channels.
LOCK: Press to display the parental menu.
TIME: Press to display Time menu.
FREEZE: Press to freeze the screen.
CC: Press to displa y the closed caption.
LIST: Press to display the TV program list.
FAV: Press to display the favorite programs.
ADD: Add this program to the favorite language.
ERASE: Delete thi s program from the favorite channels
list.
FAV+/-: Press this button +/- the favorite program list.
SLEEP: Set up the time how long the TV will turn off.
2347 5
1
HDMI
IN
VGA
IN
RF
IN
PC
AUDIO
IN
EARPHONE
OUT
6
VIDEO LR
IN
8
10
9
USB
YPb Pr
IN
LR
OUT
(Fa ctory u se only )

78
Installing Batteries in the Remote Control
Installing BatteriesInstalling Batteries
1Open the battery compartment
cover on the back side.
2Insert two 1.5V AAA size batteries in
correct polarity. Don´t mix old or used
batteries with new ones.
3Closed the cover.
Point the remote towards the remote
control sensor of the wireless TV and
use it within 7 meters.
Put the used batteries into the recyc-
ling bin since it can negatively affect
the environment.
General Description
Battery
Cover
2xsize AAA 1.5V
Battery
Cover
Antenna connection
Antenna input impedance of this unit is 75ohm. VHF/UHF 75ohm coaxial cable can be
connected to the antenna jack directly, if the antenna cable is 300ohm parallel flat feeder
cable, you need to use the 300ohm/75ohm converter to connect the antenna cable to the
antenna jack. For details Please refer to the following drawing.
Use a 75ohm - 300ohm converter
300ohm coaxial cable
Antenna feeder
ANT IN
75ohm coaxial cable
Antenna cable
Antennas with 300 ohm flat twins Leads Antennas with 75 ohm Round Leads
External Connection
The batteries shall not be eposed to ecessive heat such as sunshine
fire of the like.
External Connection
Connecting VCR
These instructions assume that you have already connected your TV to an antenna or a
cable TV system. Skip step 1 if you have not yet connected to an antenna or a cable
system.
VCR Rear Panel
Video Cable (Not supplied)
Follow the instructions in Viewing a VCR or Camcorder Tape to view your VCR tape.
Each VCR has a different back panel configuration.
When connecting a VCR, match the color of the connection terminal to the cable.
We recommend the use of cables with a Ferrite Core.
1. Unplug the cable or antenna from the back of the TV.
2. Connect the cable or antenna to the ANT IN terminal on the back of the VCR.
3. Connect an RF Cable between the ANT OUT terminal on the VCR and the ANT IN
terminal on the TV.
4. Connect a Video Cable between the VIDEO OUT jack on the VCR and the VIDEO IN
jack on the TV.
5. Connect Audio Cables between the AUDIO OUT jacks on the VCR and the AUDIO L and
AUDIO R jacks on the TV.
If you have a mono (non-stereo) VCR, use a Y-connector (not supplied) to hook up to
the right and left audio input jacks of the TV. If your VCR is stereo, you must connect
two cables.
HDM I
IN
VGA
IN
RF
IN
PC
AUD IO
IN
EAR PHON E
OUT
VID EO LR
IN
USB
YPb Pr
IN
LR
OUT
(Fa ctory u se only )

External Connection
and the AUDIO OUT jacks on the DVD player.
the TV and the COMPONENT [Y, PB, PR] jacks on the DVD player.
Connecting DVD Player/Set-Top Box
T he rear panel jacks on your TV make it easy to connect a DVD to your TV.
Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and Pr
(Red) for enhanced video quality.
Be sure to match the component video and audio connections.
For example, if connecting the video cable to COMPONENT IN, connect the audio
cable to COMPONENT IN also.
Each DVD player/STB has a different back panel configuration.
When connecting a DVD player/STB, match the color of the connection terminal to the
cable.
We recommend the use of cables with a Ferrite Core.
1. Connect a Component Cable between the COMPONENT IN [Y, PB, PR] jacks on
2. Connect Audio Cables between the COMPONENT IN [R-AUDIO-L] jacks on the ATV
Component Cable (Not supplied)
DVD Player/Set-Top Box
910
Audio Cable (Not supplied)
External Connection
Connecting DVD Player/Set-Top Box via HDMI
This connection can only be made if there is a HDMI Output connector on the external
device.
What is HDMI?
HDMI, or high-definition multimedia interface, is a next-generation interface that enables
the transmission of digital audio and video signals using a single cable without
compression.
Multimedia interface is a more accurate name for it especially because it allows multiple
channels of digital audio (5.1 channels).
The difference between HDMI and DVI is that the HDMI device is smaller in size, has the
HDCP(High Bandwidth Digital Copy Protection) coding feature installed, and supports
multi-channel digital audio.
Each DVD player/STB has a different back panel configuration.
We recommend the use of cables with a Ferrite Core.
1. Connect an HDMI Cable between the HDMI connector on the TV and the
HDMI connector on the DVD player/Set-Top Box.
HDMI Cable (Not supplied)
DVD Player/Set-Top Box
HDM I
IN
VGA
IN
RF
IN
PC
AUD IO
IN
EAR PHONE
OUT
VID EO LR
IN
USB
YPb Pr
IN
LR
OUT
HDM I
IN
VGA
IN
RF
IN
PC
AUDIO
IN
EAR PHONE
OUT
VID EO LR
IN
USB
YPb Pr
IN
LR
OUT
(Fa ctory u se only )
(Fa ctory u se only )

11 12
Connecting PC
Each PC has a different back panel configuration.
The HDMI jacks do not support PC connection.
We recommend the use of cables with a Ferrite Core.
1. Connect a D-Sub Cable between RGB/PC IN connector on the TV and the PC output
connector on your computer.
TV Rear Panel
D-Sub Cable (Not supplied)
PC
External Connection
2.Plug PHONE out connector into PHONE out jack on the TV the TV speaker will
be muted.
3. Connect the PC audio input jacks on the TV
Input Mode
Air
Cable
8VSB
Free 64/256QAM
CVBS NTSC 3.58
Supporting signals
Earphone Out
Component
VGA/PC
480p/60Hz
720p/60Hz
1080i/60Hz
HDMI
640x480/60Hz
800x600/60Hz
1024x768/60Hz
480p/60Hz
720p/60Hz
1080i/60Hz
1360x768/60Hz
480i/60Hz480i/60Hz
HDM I
IN
VGA
IN
RF
IN
PC
AUD IO
IN
EAR PHON E
OUT
VID EO LR
IN
USB
YPb Pr
IN
LR
OUT
(Fa ctory u se only )
Digital Audio System
Audio Cable (Not supplied)
Each external input source device has a different back panel configuration.
When connecting an external device, match the color of the connection terminal to the
cable.
We recommend the use of cables with a Ferrite Core.
1. Connect Audio Cables between the AUDIO L and R OUT on the TV and AUDIO IN [R-
AUDIO-L]on the Amplifier.
When an audio amplifier is connected to the AV OUT [R-AUDIO-L] terminals: Decrease
the gain (volume) of the TV, and adjust the volume level with the Amplifier's volume
Connecting Amplifier/DVD Home Theater
HDM I
IN
VGA
IN
RF
IN
PC
AUD IO
IN
EAR PHONE
OUT
VID EO LR
IN
USB
YPb Pr
IN
LR
OUT
(Fa ctory u se only )
External Connection
can’t control.

13 14
Adjust the OSD Screen
OSD Menu Operations
L
Picture
Picture Mode Standard
Color Mode Normal
Zoom Mode Normal
3DNR Weak
DLC On
PICTURE MENU
Press MENU to display the main menu, and press ◄ /► to select the Picture Menu.
Highlight the item and press ▼/▲ to select corresponding sub-menu.
Picture Mode: Dynamic/Standard/Soft/ Personal.
Color mode:This item can adjust the saturation of the color based on your own like.
Zoom mode: Four selectable Zoom Modes, Normal, Zoom, Cinema, Wide .
3DNR: Used for the noise reduction adjustment to get a better image effects.
DLC: Dynamic brightness control
Press MENU button to display the main menu.
Press◄ / ► button to select PICTURE in the main menu, it will highlight the first option.
AUDIO MENU
Press MENU to display the main menu, and press ◄ /► to select the Sound Menu.
Equalizer Standard: Adjust audio frequency band.
Audio Language: Set the language.
Surround Sound: Surround effect on or off.
Audio Only: Audio Only effect on or off.
AVC: When set the AVC on, quick volume change will be smoothed.
L
Audio
Equalizer Personal
Audio Language English
Surround Off
Audio Only Off
AVC Off
PICTURE
AUDIO
Press MENU button to display the main menu.
Press◄ / ► button to select AUDIO in the main menu, it will highlight the first option.
Adjust the OSD Screen
OSD Menu Operations
Press SOURCE button to display the input source list.
Press ▼/▲ button to select the input source you want
to watch.
Press ENTER button to enter the input source.
INPUT
AV
HDMI
PC
ENTER
TV
BASIC OPERATION
L
Channel
Air/Cable Cable
Auto Scan
Favorite
Show/Hide
Channel No.
Channel Label
DTV Signal Bad
Auto Scan
Digital channel only
Analog channel only
MENU ENTER
Scan all channels
Press MENU button to display the main menu.
Press◄ / ► button to select CHANNEL in the main menu, it will highlight the first option.
Air/Cable
press ENTER button to select it Cable or Air.
AUTO SCAN
Auto Tuning can find out all effective channel automatically.
Press ▼/▲ to select Auto Tuning, then press ENTER to start
auto searching.
If you want to stop searching, press EXIT.
CHANNEL
Component

15 16
OSD Menu Operations
LOCK
Press MENU button to display the main menu.
Press◄ / ► button to select LOCK in the main menu, it will highlight the first option.
L
Lock
Parental Controls___
Press MENU button to display the main menu.
Press button to select Lock in the main menu. It will highlight the first option.
Enter the code 0000 to enter the parental menu (see the picture below),
or press MENU to cancel.
◄ / ►
L
Lock
Change Password
System Lock On
Input Block
US
Canada
RRT Setting
Reset RRT
CHANGE PASSWORD
Press ENTER button and enter a new 4 digit password.
SYSTEM LOCK
Press ENTER to select the system lock on or off.
Unrated Lock Off
UNRATED LOCK
Press ENTER to select the Unrated lock on or off.
Enter Old Password
Clear Cancel
Enter New Password
Confirm Password
OSD Menu Operations
TIME
Press MENU button to display the main menu.
Press◄ / ► button to select TIME in the main menu, it will highlight the first option.
L
Time
Sleep Timer Off
Time Zone Atlantic
DST Off
Time Format 24-hour
Auto Sync On
Clock 2012/1/1 12:0
Wak eUp 2 012 /1/ 1 12: 0
TIME MENU
Press MENU to display the main menu, and press ◄ /►
Sleep Timer: Select the time in minutes(5min,10min,15min,30min,60min,90min,120min,
180min,240min,Personal) that you want the TV to shut off automatically after you set the
time. Cancel by setting it to Off.
Time Zone: Set to choose the time belt.
Time Format: Set to choose time display format
Auto Sync: Synchronous automatic
Clock:Press ENTER to set time.
Wake Up: Ending the state of sleep
to select the Time Menu.
SETUP
L
Setup
Menu Language English
Transparency 25%
Closed Caption
Restore Default
Setup Wizard
Blue Screen Off
Press MENU button to display the main menu.
Press◄ / ► button to select SETUP in the main menu, it will highlight the first option.
SETUPMENU
Press MENU to display the main menu , and press◄/► to select the Seput Memu.
Menu Language: Set the OSD display language. (English/ French/ Spanish)
Transparency: Set transparency of OSD.
Closed Caption: Set to hide the caption
Restore Default: Recall the default setting.
Setup Wizard: Installation guide.
Blue Screen: Set the background color to blue or black when no input signal.

8
MUTE
Troubleshooting
18
17
CANADA
Press ENTER or right arrow for to enter to CANADA ratings menu, which contains two sub-menus:
Canada English and Canada French. See next page for more details.
Adjust the OSD Screen
OSD Menu Operations
US
Press ENTER or right arrow for to enter to US ratings menu, which contains two sub-menus:
Movie Rating and TV Rating. See next page for more details.
INPUT BLOCK
HDMI PC)
press◄/►
Press ENTER to display the Input Block , AVPress ▼ / ▲ button to select (TV、 、
Component、 、
button to select “UnBlock” or “Block”.
MENU ENTER
US
TV
MPAA
Block
TV RATING
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
ALL
ALL
ALL
ALL
ALL
ALL
FV
V S L D
V
V
S
S
L
L
D
MENU
MPAA
G
PG
PG-13
R
N/A
NC-17
X Lock
MENU
Canada Eng
C
MENU ENTER
Canada
Canada Eng
Canada Fre
MENU
Canada Fre
G
C8+
G
PG
14+
18+
EXEMPT
Lock
8 ans+
13 ans+
16 ans+
18 ans+
EXEMPT
Lock

Picture defects and the reason
19