FWB MultiBall Pro User manual

MultiBall Pro - Setup Guide 3.2
Fun With Balls GmbH

Technical Specications MultiBall Pro
What's In The Box
Console
Sensor Frame
AC Power Cord
Installation Guide
Dimensions (WxHxD)
489 x 335 x 14 cm
Connectivity
Power: 110V / 220V / 230V
Internet: Ethernet / USB (Mobile Hotspot)
Video: HDMI (use quality cables)
Audio
Internal Sound System

Technical Specications MultiBall Club
The System needs a Projector, that is mounted as close and high as possible to avoid shadows.
•Use a high quality HDMI cable.
Recommended Projectors:
•Panasonic PT-VMZ40
•Panasonic PT-VMZ60
•Panasonic PT-VZ470
Required Resolution:
•WUXGA (1920x1200)
•WXGA (1280x800)
Required Aspect Ratio
•16:10
Use this site to accurately calculate the distance you need for lens and projector:
hps://panasonic.net/cns/projector/calculator/tdc/index.html
Please ask a local projector dealer to help you choose the right projector for your light conditions and the projector distance.
Recommended play area:
5,8m x 5,8m

Dimensions in mm
138 mm1599 mm
4890 mm
3090 mm
3347 mm

Hardware
Holder (x9) Sensor (x12) Cover (x8) Sensor Bolt M4 (x40) Cover Bolt M6 (x32)
Console

Cable Management
There are 7 cable outlets to run the HDMI, LAN and power cable.
138 mm1599 mm
4890 mm
3090 mm
3347 mm

Recommended Equipment
Ladder Laser Level DrillAllen Key Set
There are 52 holes
with a diameter of 8mm.
Screws and Dowels
for Wall Mounting

Step 1
Open Console
Remove the 6 screws and liup the cover.

LeSide Down (2)
Right Side Down (2)
Boom Right (1)
Boom Le(1)
Top Le(4) Top Right (4)
Console (5)
Right Side Up (2)
LeSide Up (2)
Step 2
Mount Holders and Console
1. Mount the Boom Holders
Le, Middle and Right touching
each other.
(Distance to oor 20mm)
2. Mount LeSide and Right Side.
3. Verify Leand Right are fully
leveled and parallel.
4. Mount Top Leand Top Right.
5. Mount Console (next page).
Please always make sure all proles are leveled in order to
make the top Frames touch each other with no gap.
Please select the suitable bolts, dowels and washers to aach the
frame to the wall according to wall properties (3-5 screws per part).
Boom Middle (1)

Secure the Console with 7 bolts.
Step 2
Mount Console

Mount all Sensors with the red surface facing inwards.
The sticker must face you.
Use Sensor Bolt M4.
Step 3
Mount the Sensors
Do not over-tighten the bolts!
Sensor Bolt M4
LeSide Boom
Right Side Boom
Boom Right
Boom Le
Top LeTop Right
LeSide Top
Right Side Top
Top Middle Right
Top Middle Le
Boom Middle Le
Boom Middle Right

!
Step 4
Connect Sensors
Handle the Connectors with care and tighten them.
1. Connect the Sensor Top Lewith Top LeMiddle and
the Sensor Boom Lewith Boom LeMiddle.
2. Connect the Sensor Top Right with Top Right Middle and
the Sensor Boom Right with Boom Right Middle.

Step 5
Cable connections
Connect the Sensor Cables with the Controllers.
1E
1S
3S
TXZS1 TXES1TXZS2
TXZS3
TXES2
Lvx X Lvx Y
TOP
Computer
Power
Power
CAN/RS232
COM 1 HDMI
Projector
LAN
HDMIHDMI
Power
Power Line
RXZS3
RXES2
RXZS1 RXZS2 RXES1
Calibration of the light grid:
Before the first power on after mounting the light bars to their final position put switch 3
(the array of tiny switches) up on both of the LVX-devices. Then Power on the System and
check that the green LED below the orange LED is lit. When interrupting a beam the green
light should go off. Check for both Axis X and Y. Then put down the switch 3 (to off). Now
the light grid is ready to use
Multiball setup and connection plan
S
E
1
TXZS1 TXES1TXZS2
TXZS3
TXES2
Lvx X Lvx Y
TOP
Computer
Power
Power
CAN/RS232
COM 1 HDMI
Projector
LAN
HDMIHDMI
Power
Power Line
RXZS3
RXES2
RXZS1 RXZS2 RXES1
Calibration of the light grid:
Before the first power on after mounting the light bars to their final position put switch 3
(the array of tiny switches) up on both of the LVX-devices. Then Power on the System and
check that the green LED below the orange LED is lit. When interrupting a beam the green
light should go off. Check for both Axis X and Y. Then put down the switch 3 (to off). Now
the light grid is ready to use
Multiball setup and connection plan
S
E
2
TXZS1 TXES1TXZS2
TXZS3
TXES2
Lvx X Lvx Y
TOP
Computer
Power
Power
CAN/RS232
COM 1 HDMI
Projector
LAN
HDMIHDMI
Power
Power Line
RXZS3
RXES2
RXZS1 RXZS2 RXES1
Calibration of the light grid:
Before the first power on after mounting the light bars to their final position put switch 3
(the array of tiny switches) up on both of the LVX-devices. Then Power on the System and
check that the green LED below the orange LED is lit. When interrupting a beam the green
light should go off. Check for both Axis X and Y. Then put down the switch 3 (to off). Now
the light grid is ready to use
Multiball setup and connection plan
S
E
3
TXZS1 TXES1TXZS2
TXZS3
TXES2
Lvx X Lvx Y
TOP
Computer
Power
Power
CAN/RS232
COM 1 HDMI
Projector
LAN
HDMIHDMI
Power
Power Line
RXZS3
RXES2
RXZS1 RXZS2 RXES1
Calibration of the light grid:
Before the first power on after mounting the light bars to their final position put switch 3
(the array of tiny switches) up on both of the LVX-devices. Then Power on the System and
check that the green LED below the orange LED is lit. When interrupting a beam the green
light should go off. Check for both Axis X and Y. Then put down the switch 3 (to off). Now
the light grid is ready to use
Multiball setup and connection plan
S
E
4
2E
2S
4S
3E
4E
Sender Empfänger

Step 5
Cable connections
1. Connect the Console to power outlet and to Internet.
2. Connect the projector via HDMI.
Power
LAN
HDMI
Volume
Controle

Step 6
Setup Controller (1, 2, 3, and 4)
1. Power oController 1, 2, 3 and 4 by the switches.
2. Switch up the DIP 3 on Controller 1.
3. Power on the Controller 1.
4. Switch down the DIP 3 on the Controller 1 and wait
until the „OUT 4 / IN 2“ green LED comes up.
(if this light never went o, please wait 5 seconds)
5. Test the sensor by touching the wall:
•"OUT 1" green LED blinks as you interfere the light bars.
•Center LED blink in a steady interval to show that the unit is
alive and working.
6. Power oController 1 and repeat the same steps with Controller
2-4, starting from step 1 - 6 and move on to step 7.
7. Power on Controller 1 - 4.
•Don’t change any of the DIP in the MB sensors except DIP 3
•During the sensors testing: LEDs in the center show the signal's strength in
real time and these might icker with slight signal changes, which is FINE
o/on
o/on
DIP 3
DIP 3
o/on
o/on
1
2
3
4

Step 7
Mount Covers
Carefully slide in the covers and avoid pinching or bending
the light bar cables!
If using an electric impact drill, make sure not to damage
the white surface of the wall!
Use provided bolts.
Once covers are on repeat Step 6 “Calibrate LVXs”
Cover Bolt M6
1. Mount the Covers with the sensor holes facing inwards.
2. Use Cover Bolt M6.

Step 8
Adjust Projector
To get a picture, always make sure you power on the projector rst and
then the MultiBall console.
If the game does not t in the visible picture, get in touch with us so we
can remotely change the seings
Using ‘Shi’ and ‘Corner Correction’ in your projector, align
the picture so it perfectly ts into the frame.
Now it is time to test the system for the rst time. Everything
should run smoothly.
1. Disconnect the Console from the power outlet.
2. Switch on the projector.
3. Connect the Console to the power outlet.

Step 9
Mount MultiBall Console Cover
Use this step to adjust the volume of the amplier. The
volume can also be adjusted in the menu so try to nd the
best level suitable for you.
1. Put back the Cover.
2. Use Cover Bolt M6.
Cover Bolt M6

Maintenance
In case of any problems of system not working, always rst
check the Sensors if they are clean and without any
obstruction.
Take care of the system to avoid any kind of physical
damage.
Vacuum sensors once a week.
(with covers on)
1. Do not block the Sensors.
2. Do not step on the Sensor Frame.

Home Screen
1. Choose between Games and Trainings.
2. Start by touching an icon.
3. Remote control by Smart Phone.
Scan QR-
Code to
connect with
the MultiBall
Smart Phone
App.