Lifetime PUMP ADJUST 90487 User manual

PUMP ADJUST™
BASKETBALL SYSTEM
Icon Legend................................2
Notices....................................3
Pole Assembly.............................4
Pole to Base Assembly.................9
Backboard to Rim Assembly.......13
Backboard to Pole Assembly.......19
Parts Identifier..........................i-iv
Handle Assembly.......................23
Final Assembly..........................32
Maintenance Instructions..........36
Warning Sticker........................37
Registration........................38
Warranty................................39
(2) (2) (1)
(1) (1) (1)
(1) (1) (1)
(1)
3/8”, 1/2”, 9/16”, 3/4” 1/2”
3/16”
(2)
(375 lb)
TOOLS REQUIRED TABLE OF CONTENTS
• Before you start, decide how you would like to fill
your base (sand is recommended, see page 29).
• Assembly should take 2 people about 2-3
hours to complete.
ASSEMBLY INSTRUCTIONS
MODEL #60091
MODEL 90487
Save this instruction in the event that the manufacturer has
to be contacted for replacement parts.
BEFORE ASSEMBLY:
CONTACT LIFETIME CUSTOMER SERVICE:
Call: 1-800-225-3865
7:00 am–5:00 pm (Monday–Friday) MST
and 9:00 am–1:00 pm Saturday MST
QUESTIONS? MODEL# AND PRODUCT ID
(you will need both when contacting us)
Model Number: 90487
Product ID:
For Customer Service in Mainland
Europe and the United Kingdom,
E-mail:[email protected]
Live Chat: www.lifetime.com
(click on “Ask An Expert” tab)
Video Instructions:
www.youtube.com/lifetimeproducts
1/4”
(1)
COPY

2
• Indicates the parts to be used for a section.
• Indicates special heed should be taken when reading.
• Indicates the hardware to be used for a section.
• Indicates the tools to be used for a section.
• Indicates no hardware required for a specific page.
• Indicates no parts required for a specific section.
• Indicates to use/not to use an electric drill for a specific step.
ICON LEGEND
• Indicates the use of a Centerlock Nut. A Nut with this marking will require some effort to tighten.
This hardware was designed with this feature in order to prevent loosening later.
1184985 B 8/23/2017
COPY

3
WARNINGS & NOTICES / AVERTISSEMENTS ET AVIS / ADVERTENCIAS Y AVISOS
Most injuries are caused by misuse and/or not following instructions. Use caution when using this product.
To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing
material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware
identifier and parts list in this document. Proper and complete assembly, use and supervision are essential for proper operation and to reduce the
risk of accident or injury. A high probability of serious injury exists if this product is not installed, maintained, and operated properly.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
• If using a ladder during assembly, use extreme caution.
• Two capable adults are recommended for this operation.
• Check base daily for leakage. Leaks will cause system to fall.
• Assemble the pole sections properly. Failure to do so could cause the pole sections to separate during play or transport.
• Minimum operational height is 6 ft 6 in (1.98m) to the bottom of the backboard.
SAFETY INSTRUCTIONS
COPY

4
SINOSE OBEDECEN ESTAS ADVERTENCIAS PUEDEN PRODUCIRSE
GRAVESLESIONESY/O DAÑOS A LA PROPIEDAD.
Elpropietariodel sistema debe asegurarse de que todos
losjugadoresconozcan y respeten estas reglas para que el
sistemaseuse en forma segura.
W
FAILURETOFOLLOW THESE WARNINGSMAY RESULTINSERIOUS INJU
AND/ORPROPERTYDAMAGE.
Ownersmustensure that all players know and follow thes
e
rulesforsafe operation of the system.
•Only hang from the Rim briefly to regain balance or avoid injuringothers.Release the Rim as soon as safely possible. •During play,especially when performing dunk type activit
i
keepplayer’sface away from the Backboard, Rim, and Net Seriousinjurycould occur if teeth/face come in contact wit
h
theBackboard,Rim, or Net. Playershould wear a mouth guardduringplay. •Do not slide, climb, or play on Base or Pole. •Completely fill Base according to manufacturer’s instructions.Never leave the unit standing in an upright positionwithoutfirst filling the Base with weight or the syst
e
willtipquickly causing serious personal injury. •When adjusting height or moving system, keep hands an
d
fingersawayfrom moving parts. •Do not allow children to move or adjust system. •Do not wear jewelry (rings, watches, necklaces, etc.) duri
n
play.Objectsmay entangle in Net. •Keep water and organic material away from Pole Base. Gr
a
litter,etc.could cause corrosion and/or deterioration. •Never play on damaged equipment.
•Cuélguesedel aro sólo en forma breve, para recuperar el equilibr
i
oevitar lesionar a otros jugadores. Suéltese del aro lo más pron
t
quepuedahacerlo con seguridad. •Durante el juego, especialmente al embocar violentamente
d
alto,lacara de los jugadores deb e mantenerse alejada del tabler
o
elaroy la red. Pueden producirse lesiones graves si los dientes o
l
caraentranen contacto con el tablero, el aro o la red. Los jugador
e
debenusarun protector bucal durante el juego. •Nose deslice, no trepe ni juegue sobre la base o el poste. •Llene la base completamente siguiendo las instrucciones d
e
fabricante.Nunca deje la unidad en posición de uso sin hab
e
llenadopreviamente la base con material de contrapeso, pues
e
sistemapodría tumbarse rápidamente y causar graves lesion
e
personales. •Mantengalas manos y los dedos alejados de las piezas movibl
e
cuandoregule la altura o desplace el sistema. •Nodeje que los niños regulen ni desplacen el sistema. •Nouse joyas (anillos,relojes, collares o g argantillas,etc.) durante
e
juego.Estosobjetos pueden engancharse en la red. •Lasuperficiedonde se coloque la base deb e estar lisa y desprovis
t
depiedras,grava u otros objetos. Las perforaciones pueden origin
a
pérdidas,yéstas pueden hacer que el sistema se tumbe. •Guarde aqua y materia orgánica. Césped, basura,etc., prodria causarcorrosiónet/o deterioros.
•Controle el poste y todas las piezas metálicas una vez al m
e
enbusca de signos visibles de corrosión (oxidación, picadura
s
escamado).Elimine todo rastro de óxido y vuelva a pintar c
o
esmalteparaexteriores. Si el óxido ha penetrado cualquier pieza
d
acero,reemplaceesa pieza de inmediato. •Inspeccioneel sistema antes de cada uso para veri ficar que es
t
adecuadamentecontrapesado, que los elementos de fijación
n
esténflojos,que no haya desgaste exce sivo, inestabilidad ni sign
o
decorrosión.Si encuentra irregularidades, rep árelas antes de us
a
elsistema. Nuncajueguecon un equipo dañado. •Nouse el sistema en pres encia de vientos fuertes o condicion
e
climáticasadversas,ya que puede tumbarse. Coloque la unidad
e
suposición de almacenamiento y/o en una zona a resguardo d
e
viento,lejos de propiedades personales que puedan dañarse si
e
sistemasecae, y de líneas de suministro de energía. •Nouse el sistema para levantar ningún objeto. El mecanismo es
t
diseñadopara elevar solamente el peso del tablero con el aro.
N
cuelguenada de la agarradera, el aro, el tablero ni los brazos
d
elevación,yaque esto puede dañar el sistema y anular la garantía.
www.
l
ADVERTENCIA
LifetimeProducts,Inc., Clearfield, UT 84016
1-800-225-3865
BCO
Metal Parts
Hardware Bag
TOOLS REQUIRED
PARTS REQUIRED
HARDWARE REQUIRED
POLE ASSEMBLY
1
Scrap Wood
Electric Drill
Warning Sticker
3/8"
(2)
ABB (x2)
AAF (x2)
ABE (x2) CMV (x2)
ABR (x2)
ALH (x1)
ALF (x1)
ALE (x1)
ALL (x1)
Measuring Tape Pencil
COPY

5
TOOLS AND HARDWARE REQUIRED
XSECTION 1 (CONTINUED)
• Use a pencil to mark a small line 4” from the top
of the Middle and Bottom Poles (ALF & ALE).
• Secure the Pole Bracket (ALL) to the Top Pole (ALH)
with the hardware as shown.
1.1 1.2
AAF (x2)
3/8" (x2)
ABB (x2)
ABE (x2)
ABR (x2)
ALH
ALL ABB
AAF
ABR
ABE
ALF ALE
FAUTEDENE PAS SUIVRE CES AVERTISS
E
DESBLESSURESGRAVES ET/OU DE
S
Lepropriétaire doit s’assurer
q
naissentet appliquent les règl
e
l’équipementen t
o
E
NCIASPUEDENPRODUCIRSE
OSALA PROPIEDAD.
asegurarse de que todos
e
nestas reglas para que el
f
ormasegura.
G
SMAY RESULT IN SERIOUS INJURY
RTYDAMAGE.
layersknow and follow these
t
ionof the system.
y
to regain balance or avoid
assoon as safely possible.
p
erformingdunk type activities,
e
Backboard, Rim, and Net.
t
h/facecome in contact with
a
yershould wear a mouth
Baseor Pole.
to manufacturer’s
itstanding in an upright
a
sewith weight or the system
ersonalinjury.
i
ngsystem, keep hands and
oradjust system.
t
ches,necklaces, etc.) during
e
t.
a
laway from Pole Base. Grass,
a
nd/ordeterioration.
ment.
•Surface beneath the Base mus
gravelor other objects. Puncture
s
causesystem to tip over.
•Once a month check Pole and
corrosion(rust, pitting, chipping)
.
andrepaint with exterior enamel.
steelpart, replace that part imm
e
•Check system before each use
hardware,excessive wear,instab
i
andrepair before use.
•Do not use system during wind
maytip over.Place system in an
a
windor in an area away from pro
ifthe system falls, and from over
h
•Do not use the system to lift or
mechanismis designed to lift onl
y
Backboardand Rim. Do not han
g
Rim,Backboard, or Lifter Arms a
thiswill damage the system and
v
thewarranty.
•Ne vous suspendez pas à l’ann
e
retrouvervotre équilibre ou éviter
d
Relâchezl’anneauaussitôt que poss
i
•Lors d’un match, particulièreme
n
visagedujoueur ne doit pas faire fac
e
filet.Lejoueur risque de graves bles
s
entrentencontact avec le panneau,
l
doiventtoujoursporter un protège-d
e
•Ne glissez pas, ne grimpez pas, et
poteau.
• Remplissez complètement la b
a
fabricant.Ne laissez jamais l’unité d
d’abordrempli la base avec un p
o
basculerrapidementet causer de gr
a
• Lorsque vous ajustez la haute
u
l’équipement,gardezvos mains et d
o
• Ne permettez pas aux enfan
t
l’équipement.
•Ne portez pas de bijoux (bagues,
vousjouez.Ces objets pourraient s’a
c
•La surface sur laquelle est posée
gravieroutout autre objet qui pourra
i
unefuitece qui pourrait faire bascul
e
•Gardez de l’eau et de la matiére
gazon,les déchets, etc. pourraient
p
détérioration.
•Une fois par mois, vérifiez que le
métalne montrent pas de signes
écaillage).Enlevez toute la rouille et
unepeinturepour extérieur. Si la roui
acier,vousdevrez remplacer imméd
i
•Achaque fois que vous allez utilise
l’équilibre,la possibilité de pièces d
e
del’équipement et tout signe de cor
r
avantutilisation.
•Nejouez jamais avec un équipem
e
• N’utilisez pas l’équipement lors
de mauvais temps. L’équipeme
n
l’équipementdans un endroit abrité
qu’ilpourraitendommager s’il bascu
•N’utilisezpas l’équipement pour le
v
Sonmécanisme a été conçu unique
panneauet de l’anneau. N’accroch
e
aupanneau ni aux leviers sous pein
e
etd’annulerla garantie.
e
ve,pararecuperar el equilibrio
S
uéltesedel aro lo más pronto
alembocar violentamente de
m
antenersealejada del tablero,
sionesgraves si los dientes o la
r
o,elaro o la red. Los jugadore s
n
teeljuego.
s
obrelab ase o el poste.
i
guiendolas instrucciones del
e
nposición de uso sin haber
m
aterialde contrapeso, pues el
e
ntey c ausar graves lesiones
a
lejadosde las piezas movibles
e
lsistema.
e
splacenelsis tema.
e
sogargantillas, etc.) durante el
harseen la red.
a
sedebeestar lisa y desprovista
s
perforaciones pueden originar
elsistemas e tumbe.
Césped,basura,etc.,prodrian
z
asmetálicas una vez al mes
o
rrosión(oxidación, picaduras,
e
óxido y vuelva a pint ar con
apenetrado cualquierpieza de
e
diato.
a
dauso para verificar que esté
e
los elementos de fijación no
e
xcesivo,inestabilidad ni signos
d
ades,repárelas antes de usar
o.
e
vientos fuertes o condiciones
u
mbarse.Coloque la unidad en
o
en una zona a resguardo del
alesque puedan dañarse si el
n
istrode energía.
n
gúnobjeto.El mecanismo est á
p
esodel tablero con el aro. No
a
ro,el tablero ni los brazos de
e
lsistemay anular la garantía.
www.lifetime.com
N
CIA AVERTISS
E
4
016
Pencil
Measuring Tape

6
1.2
1.2
• Make sure the holes indicated are on the same side of the Pole assembly as the Pole Bracket. Slide the Top Pole (ALH)
onto the Middle Pole (ALF) as shown.
• In order to seat the Poles, strike the end of the
Pole very hard five to six times on a piece of scrap
wood. The Top Pole (ALH) should come down until it
covers the 4” pencil mark at the top of the Middle
Pole (ALF) and no further. If the Top Pole does not
completely cover the mark at the top of the Middle
Pole after seating, DO NOT COMPLETE ASSEMBLY. Call
our Customer Service Department.
TOOLS AND HARDWARE REQUIRED
1.3
1.4
XSECTION 1 (CONTINUED)
ALH
ALF
(1)
6x
ATTENTION: THIS STEP CANNOT BE REVERSED!
• Do not strike your feet with the
Pole sections, as serious injury
may occur.
!
WARNING
The Poles must be seated together! Even if the
Poles cover the slots before seating, they must be
struck on a hard surface five to six times! Failure
to seat the Poles correctly could allow the Poles to
separate during use, which could lead to serious
personal injuries or property damage.
!

7
1.5 1.6
TOOLS AND HARDWARE REQUIRED
XSECTION 1 (CONTINUED)
ALH
ALF
ALE
ALL
Crimped end
• Slide the Middle Pole (ALF) onto the
Bottom Pole(ALE) as shown. Make sure
the crimped side at the end of the
Bottom Pole (ALE) faces the opposite
direction as the Pole Bracket (ALL).
• In order to seat the Poles, strike each end of the Pole very
hard five to six times on a piece of scrap wood or cardboard.
This must be done even if the Poles cover the 4” mark before
seating has occurred. If the Top and Middle Poles (ALH & ALF) do not
completely cover the marks on the Middle and Bottom Poles (ALF &
ALE) after seating, DO NOT COMPLETE ASSEMBLY. Call our Customer
Service Department.
(1)
6x
ATTENTION: THIS STEP CANNOT BE REVERSED!
WARNING
The Poles must be seated together! Even if the
Poles cover the slots before seating, they must be
struck on a hard surface five to six times! Failure
to seat the Poles correctly could allow the Poles to
separate during use, which could lead to serious
personal injuries or property damage.
!
• Do not strike your feet with the
Pole sections, as serious injury
may occur.
!

8
• After the Poles have been seated, insert two #10 x .62” Self-Tapping Screws (CMV) into the back of the Pole as shown.
1.7
CMV (x2)
• For ease of installation, chuck the
Self-Drilling Screws directly into the
drill if your drill (see Figure 1, not
available on all drills), or use a 3/8”
Hex Driver (see Figure 2, Hex Driver
not included).
!
TOOLS AND HARDWARE REQUIRED
XSECTION 1 (CONTINUED)
ALH
ALF
ALE
CMV
Figure 1
Figure 2

9
POLE TO BASE ASSEMBLY
2
BCQ
Metal Part
Hardware Bag
TOOLS REQUIRED
PARTS REQUIRED
HARDWARE REQUIRED
AMU (x2)
AJM (x1)
Plastic Parts
(2) (1)
1/2” CCL-3/16”
(2)
21 3/4 ”
AJD (x1)
ALI (x2)
AJN (x1)
38”
CCL (x2)
AAE (x2)
ABD (x4)
AAO (x2)
DRZ (x1)
BTS (x1)

10
TOOLS AND HARDWARE REQUIRED
XSECTION 2 (CONTINUED)
2.1
• Make sure the Rubber Gasket
is inside the Base Cap.
AJM
AJN
AJN
Rubber Gasket
• Screw the Base Cap (AJN) onto the Base (AJM) as shown.
!
AJN
2.2 • Position the Pole assembly on the Base (AJM) as shown. Slide the 21 3/4” Axle (AJD) through one of the Wheels (AMU)
and into the Base (AJM). Have one adult position the Bottom Pole (ALE) within the Base as shown with the lip at the
bottom of the pole facing away from the base. Insert the Axle through the Bottom Pole and into the other side of the
Base and through the other Wheel.
• It may be necessary to use a
Rubber Mallet to tap the Axle
into place.
!
AJM
ALE
AMU AMU
AJD
ALE

11
TOOLS AND HARDWARE REQUIRED
XSECTION 2 (CONTINUED)
2.3 • Attach the flattened end of the Pole Brace (ALI) to the Base (AJM) with the hardware shown. Only finger tighten the
hardware.
AAE (x2) ABD (x4) AAO (x2)
1/2" (x2)
2.4 • Repeat step 2.3 to install the remaining Pole Brace to the other side of the base. Make sure the unattached ends
of the Pole Braces line up as shown.
ALI
AAE
ABD
ABD
AAO

12
TOOLS AND HARDWARE REQUIRED
XSECTION 2 (CONTINUED)
• Tip the system forward and rest the Pole on the ground. Do not stand the system up until it is filled with either sand or water later in
the assembly. Tighten the hardware shown.
2.6
2.5 • Attach the Pole Braces (ALI) to the Bottom Pole (ALE) with the hardware shown.
3/16”
BTS (x1)
CCL (x2)
1/2" (x2)
DRZ (x1)
DRZ
BTS

13
3
AOW (x1)
AOU (x1)
AJW (x2)
ABK (x4)
BACKBOARD TO RIM ASSEMBLY
HARDWARE REQUIRED
Hardware Bag
AAQ (x2)
APY (x1)
EAP (x2)
ADR (x4)
ABQ (x1)
PARTS REQUIRED
Metal Parts
ALX (x1)
AMA (x1)
AJI (x1)
Plastic Parts / Pièces en plastique / Piezas de plástico
ALD (x1)
BCS
TOOLS REQUIRED
(x1)
9/16" (14 mm)
(x2)
1/2" (13 mm)
(x1)
AMY (x2)
DFD (x1)
ABB (x4) DFE (x4)
AAV (x2)

14
XSECTION 3 (CONTINUED)
TOOLS AND HARDWARE REQUIRED
3.1
3.2
9/16" (11 mm)
(x2)
• Attach the Backboard Brackets (AMY) to the Backboard using the hardware indicated.
ABB
DFE
DFE
DFE
DFE
ABB
AMY
• Insert two Carriage Bolts (EAP) through each hole in the Rim Pivot Bracket (APY).
EAP
APY
EAP
EAP (x2) APY (x1)
DFE (x4)
ABB (x4)

15
XSECTION 3 (CONTINUED)
TOOLS AND HARDWARE REQUIRED
3.3
3.4
1/2" (13mm)
(x1)
AAQ (x2)
ABQ (x1)
• Use the 1/2" (13 mm) socket head from the socket head wrench to press one Push Nut (AAQ) onto one end of the
Axle (ABQ).
AAQ
ABQ
• The Push Nut (AAQ) should rest about 1/4" (6 mm) from the end of the Axle (ABQ). If the Push Nut (AAQ) slips
on too far, continue sliding it to the other end of the Axle (ABQ) to remove it and try again.
!!
• Slide the end of the Axle (ABQ) through the Rim (ALX) and the Rim Pivot Bracket (APY). Press the Push Nut (AAQ) onto the
end of the Axle (ABQ). Use the 1/2" (13 mm) socket head to secure the Push Nut (AAQ) if needed.
AAQ
ABQ
APY
ALX
ABQ
1/2" (13 mm) Socket Head

16
XSECTION 3 (CONTINUED)
TOOLS AND HARDWARE REQUIRED
3.5
(x1)
3.6
• Lay the Backboard (AJI) on a table or bench. Insert the U-Bolt (AOU) through the upper part of the opening on the backside of
the Backboard (AJI) as shown.
• Insert the U-Bolt (AOU) through the top holes of the Backboard and the Rim.
!!
1/2" (13mm)
AOU (x1)
AOU
DFD
• Connect the Rim (ALX) and Plastic Guard (ALD) to the Backboard (AJI) with the hardware shown.
ALX
ALD
AJI
ABK
AOU
EAP
ABK (x2)
ABK
EAP

17
XSECTION 3 (CONTINUED)
TOOLS AND HARDWARE REQUIRED
3.7
ABK (x2)
3.8
1/2" (13 mm)
• Thread the Jam Nuts (AAV) all the way down on the U-Bolt (AOU) as shown.
(x1)
AAV
AOU AOU
• Slide the Compression Springs (AJW) onto the U-Bolt (AOU), and place the Spring Retainer Plate (AOW) over the Compression
Springs. Tighten the Nylock Flange Nuts (ABK) until the Rim (ALX) does not wobble.
• Do not completely tighten the Nuts in this step!
Tightening the Nuts adjusts the Rim Tension.
!
AJW
ABK ABK
AOW
AOU
AJW (x2) AOW (x1) AAV (x2)

18
XSECTION 3 (CONTINUED)
TOOLS AND HARDWARE REQUIRED
• Attach the Rim Cover Plate (AMA) to the Rim using Screws (ADR).
ADR
AMA
3.9
ADR (x4)

19
Metal Parts Plastic Part
Hardware Bag
TOOLS REQUIRED
PARTS REQUIRED
HARDWARE REQUIRED
BACKBOARD TO POLE ASSEMBLY
4
(2)
3/4”
(1)
BCR
AAX (x4)
DFB (x2)
ABN (x8)
AKC (x2)
AKB (x2)
21 1/8” (53.6 cm)
7 1/2”
AAD (x2)
DGA (x2)
7 1/16”
ALM (x1)
25 7/8” (65.7 cm)

20
XSECTION 4 (CONTINUED)
TOOLS AND HARDWARE REQUIRED
4.1 • Finger-tighten the Short Extension Arms (AKC) to the Backboard Brackets with the hardware shown.
4.2 • Finger-tighten the Long Extension Arms (AKB) to the Backboard Brackets with the hardware shown. If needed, use a
rubber mallet to tap the bolt into place.
AAX (x2) DFB (x2)
7 1/2”
DGA (x2)
ABN (x4)
AAX
AAX
AKB
AKB
AKB
DGA
DGA
DFB
DFB
ABN ABN
AKC
AKC
ABN ABN
• If you experience difficulty passing the
bolt through the holes, try using a wrench
to rotate the bolt until it passes through.
DO NOT STRIKE THE BOLT to assist it
through the holes in this step.
!
3/4” (x2)
• If you experience
difficulty passing the
bolt through the holes,
try using a wrench to
rotate the bolt until it
passes through. DO
NOT STRIKE THE BOLT
to assist it through the
holes in this step.
!
• If necessary, use a bolt to remove any
excess powder coating from the holes in the
Backboard Brackets.
!