Fyllo f8 User manual

fyllo f8
ESPRESSO COFFEE MACHINE
INSTRUCTION MANUAL
PLEASE READ THIS INSTRUCTION MANUAL AND THE SAFETY INSTRUCTIONS BEFORE OPERATING THE APPLIANCE!

- 2 -
CONGRATULATION ON YOUR PURCHASE!
IF YOU LOOK IT AFTER PROPERLY IT WILL REWARD YOU WITH MANY YEARS OF GOOD SERVICE.
BEFORE USING YOUR NEW MACHINE, PLEASE READ THIS OPERATING MANUAL CAREFULLY, PAYING PARTICULAR
ATTENTION TO THE SAFETY PRECAUTIONS.
PURCHASE INFORMATION
PRODUCT:
MODEL:
SERIAL NUMBER:
PLACE OF PURCHASE:
DATE OF PURCHASE:

- 3 -
CONTENTS
1. SAFETY PRECAUTIONS ................................................................................................................................................................................................. 4
2. UNPACKING .............................................................................................................................................................................................................. 5
3. BEFORE USING FOR THE fiRST TIME ................................................................................................................................................................................. 5
4. CAPSULES / POD TYPE THAT CAN BE USED ........................................................................................................................................................................ 5
5. OVERVIEW OF MACHINE PARTS AND CONTROLS ................................................................................................................................................................ 6
6. FILL/REFILL WATER TANK ............................................................................................................................................................................................. 7
7. FILLING BY REMOVING THE WATER TANK ......................................................................................................................................................................... 7
8. FLUSHING OUT THE MACHINE ....................................................................................................................................................................................... 7
9. BREWING COFFEE ....................................................................................................................................................................................................... 8
10. REFILLING THE INTERNAL CIRCUIT WHEN WATER TANK IS OUT OF WATER DURING BREWING ................................................................................................. 9
11. ENERGY SAVING MODE .......................................................................................................................................................................................... 9
12. PROGRAMMING THE COFFEE VOLUME ...................................................................................................................................................................... 9
13. CLEANING ........................................................................................................................................................................................................ 10
14. FACTORY RESET ................................................................................................................................................................................................. 11
15. STEAMING OUT / STORAGE / TRANSPORT ............................................................................................................................................................... 11
16. DECALCIFICATION .............................................................................................................................................................................................. 12
17. TROUBLE SHOOTING ........................................................................................................................................................................................... 13
18. WARRANTY/REPAIRS ........................................................................................................................................................................................... 14
19. SPECIFICATIONS ................................................................................................................................................................................................. 15
20. MODEL NUMBERS: ............................................................................................................................................................................................. 15

- 4 -
1. SAFETY PRECAUTIONS
PLEASE TAKE TIME TO READ THESE SAFETY PRECAUTIONS CAREFULLY BEFORE CONNECTING
YOUR MACHINE TO THE POWER SUPPLY. IT IS ESSENTIAL TO FOLLOW THE OPERATING
INSTRUCTIONS.
ALWAYS PULL OUT THE POWER PLUG BEFORE:
• RELOCATING THE MACHINE
• CLEANING OR MAINTENANCE
• LONG PERIODS OF DISUSE
NEVER CLAMP OR RUN THE POWER CABLE OVER SHARP CORNERS OR EDGES.
DANGER OF ELECTRIC SHOCK! DAMAGED POWER CABLES MAY ONLY BE REPLACED AT THE
CUSTOMER SERVICE CENTRE.
DANGER OF ELECTRIC SHOCK! NEVER TOUCH THE POWER PLUG/SOCKET/CABLE OR THE
MACHINE WITH DAMP OR WET HANDS. NEVER UNPLUG BY PULLING OUT THE POWER CABLE;
ALWAYS REMOVE THE PLUG.
IF YOU NEED AN EXTENSION CABLE, MAKE SURE IT IS SUITABLE FOR YOUR MACHINE (3-POLE
GROUNDED, 1.5 MM2 CONDUCTOR CROSS-SECTION), AND LAY THE CABLE TO AVOID
TRIPPING.
DANGER OF SCALDING! NEVER MOVE THE MACHINE DURING OPERATION!
NEVER OPERATE THE MACHINE WITHOUT WATER.
ALWAYS MAKE SURE THERE IS WATER IN THE WATER TANK NOT LESS THAN MINIMUM LEVEL.
DANGER OF BURNING! NEVER TOUCH VERY HOT PARTS OF THE MACHINE (E.G. BREW UNIT
DURING OPERATIONS).
DANGER OF SCALDING! DO NOT TOUCH THE STEAM OR WATER JETS.
DANGER OF SCALDING! DO NOT MOVE THE OPERATING LEVER WHEN THE MACHINE IS STILL
UNDER PRESSURE MAKING COFFEE.
DO NOT USE THE MACHINE IN CASE OF:
• FAULTY OPERATION
• DAMAGED POWER CABLE
• AFTER FALLING OR OTHER DAMAGE IN SUCH CASES IMMEDIATELY HAVE THE
MACHINE CHECKED AND REPAIRED, IF NECESSARY, AT THE CUSTOMER SERVICE
CENTRE.
CHOOSE A DRY, STABLE AND LEVEL SUPPORT SURFACE NOT IMMEDIATELY UNDERNEATH THE
POWER POINT, AT LEAST 60 CM AWAY FROM THE WASHBASIN AND TAPS.
NEVER PLACE ON FLAMMABLE/FUSIBLE SURFACES OR EQUIPMENT.
NEVER PLACE THE MACHINE OR POWER CABLE ON OR NEARER THAN 50 CM TO HOT
SURFACES OR OPEN FLAMES.
NEVER COVER THE MACHINE DURING OPERATION.
KEEP CHILDREN AWAY FROM THE MACHINE DURING OPERATION.
ONLY USE THE MACHINE IN DRY ROOMS.
DANGER OF TRIPPING! DO NOT LET THE POWER CABLE HANG DOWN.
THIS MACHINE IS ONLY INTENDED FOR HOUSEHOLD USE.
PULL OUT THE POWER PLUG AND ALLOW THE MACHINE TO COOL DOWN COMPLETELY BEFORE
CLEANING AND OR MAINTENANCE.
TO PREVENT DAMAGE, NEVER USE REPLACEMENT PARTS OR ACCESSORIES NOT
RECOMMENDED BY THE MANUFACTURER.
THIS APPLIANCE IS NOT INTENDED FOR USE BY YOUNG CHILDREN OR INFIRM PERSONS
UNLESS THEY HAVE BEEN ADEQUATELY SUPERVISED BY A RESPONSIBLE PERSON TO ENSURE
THAT THEY CAN USE THE APPLIANCE SAFELY, YOUNG CHILDREN SHOULD BE SUPERVISED TO
ENSURE THAT THEY DON’T PLAY WITH THE APPLIANCE.
IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY THE MANUFACTURER, ITS
SERVICE AGENT OR SIMILARLY QUALIFIED PERSONS IN ORDER TO AVOID A HAZARD.
THIS APPLIANCE IS INTENDED TO BE USED IN HOUSEHOLD AND SIMILAR APPLICATIONS SUCH
AS:
• STAFF KITCHEN AREAS IN SHOPS, OFFICES AND OTHER WORKING
ENVIRONMENTS.
• FARMHOUSES.
• BY CLIENTS IN HOTELS, MOTELS AND OTHER RESIDENTIAL TYPE
ENVIRONMENTS.
• BED AND BREAKFAST TYPE ENVIRONMENTS.
NOTES ON THIS OPERATING MANUAL
THIS OPERATING MANUAL CANNOT COVER ALL POSSIBLE CIRCUMSTANCES. FOR FURTHER INFORMATION OR IN CASE OF PROBLEMS NOT ADEQUATELY COVERED IN THIS OPERATING
MANUAL, PLEASE CONTACT THE SERVICE AND SALES CENTRE.
PLEASE KEEP THIS OPERATING MANUAL SAFE AND PASS IT ON TO THE NEXT USER.

- 5 -
2. UNPACKING
REMOVE YOUR ESPRESSO COffEE MACHINE FROM ITS PACKAGING. AFTER UNPACKING, PLEASE CHECK THAT THE FOLLOWING PARTS ARE INCLUDED:
• WATER TANK
• COffEE MACHINE
• MANUAL
CHECK THAT YOUR HOME POWER SUPPLY VOLTAGE IS THE SAME AS MARKED ON THE MACHINE RATING PLATE
DESTROY ALL THE PLASTIC BAGS TO PREVENT DANGER TO CHILDREN!
TIP: KEEP THE PACKAGING FOR TRANSPORTING THE MACHINE (E.G. FOR REMOVALS, SERVICING, ETC.)
NOTE: YOU MAY fiND A LITTLE WATER REMAINING IN THE MACHINE. IN ORDER TO ENSURE THAT THIS MACHINE WORKS PERFECTLY, IT WAS TESTED WITH WATER BEFORE LEAVING
THE FACTORY.
3. BEFORE USING FOR THE fiRST TIME
CAUTION: IMPROPER HANDLING OF ELECTRICAL EQUIPMENT IS DANGEROUS AND CAN BE LETHAL. PLEASE PAY ATTENTION TO THE SAFETY PRECAUTIONS IN THIS MANUAL, IN
PARTICULAR THE FOLLOWING:
• DANGER OF SCALDING: BEWARE OF HOT WATER!
• DO NOT OPERATE THE MACHINE WITH AN EMPTY WATER TANK OR WATER IS LESS THAN MINIMUM LEVEL.
• DO NOT OPEN THE HANDLE WHEN THE MACHINE IS BREWING.
• ALWAYS PULL OUT THE POWER PLUG BEFORE CLEANING THE MACHINE.
• ONLY USE THE MACHINE IN A DRY ROOM.
• THOROUGHLY RINSE OUT THE WATER TANK WITH FRESH WATER BEFORE USING FOR THE fiRST TIME.
• CLEAN THE COffEE MACHINE USING A DAMP CLOTH ONLY.
4. CAPSULES / POD TYPE THAT CAN BE USED
THERE ARE 2 VERSIONS OF THE FYLLO F8 ESPRESSO MACHINE:
1. F8-NES – FOR NESPRESSO®* CAPSULES OR CERTAIN COMPATIBLE CAPSULES, THE MACHINE DOES NOT WORK WITH ALL COMPATIBLE CAPSULES.
2. F8-ESE – FOR ESE PODS (EASY SERVING PODS).
* NESPRESSO IS THE TRADEMARK OF NESTLE SA, NO CONNECTION WITH MACHINE MANUFACTURER OR THE MACHINE DISTRIBUTOR/SELLER.

- 6 -
5. OVERVIEW OF MACHINE PARTS AND CONTROLS
A
HANDLE FOR INSERTION OF CAPSULE OR ESE POD
B
ESPRESSO AND LUNGO BUTTONS
C
COFFEE DISPENSER, ADJUSTABLE
D
DRIP TRAY
E
SIDE WALL OF MACHINE
F
WATER TANK COVER
G
WATER TANK (REMOVABLE)
H
POWER CORD
I
MAIN POWER SWITCH
J
USED COFFEE CAPSULE/ POD CONTAINER
K
DRIP TRAY COVER
L
DRIP TRAY (REMOVABLE)

- 7 -
6. FILL/REFILL WATER TANK
BEFORE USING FOR THE FIRST TIME OR AFTER LONG
PAUSES (E.G. HOLIDAYS) THE MACHINE MUST BE
FLUSHED OUT. THIS SHORT PROCEDURE CAN FLUSH OUT
AND CLEANS THE INTERNAL PIPING THOROUGHLY.
THERE ARE TWO WAYS TO FILL THE WATER TANK:
DIRECTLY INTO THE MACHINE, BY USING FOR EXAMPLE A
JUG, OR BY REMOVING THE WATER TANK.
FILLING WITHOUT REMOVING THE TANK RAISE THE
WATER TANK LID. FILL THE TANK UP TO THE “MAX”
MARK WITH COLD FRESH WATER (THE MAXIMUM
CAPACITY IS 0.8 LITRE), OR AT LEAST THE “MIN” MARK.
7. FILLING BY REMOVING THE WATER TANK
HOLD THE WATER GRIP AT TILTING
ANGLE AS SHOWN IN DIRECTION 1 TO
REMOVE THE WATER TANK FROM THE
MACHINE. FILL THE TANK UP TO THE
“MAX” MARK WITH COLD FRESH
WATER (THE MAXIMUM CAPACITY IS
0.8 LITRE). OR AT LEAST THE “MIN”
MARK.
SLIDE THE WATER TANK SLOWLY ON WATER TANK BASE, WHEN THE WATER TANK
OUTLET IS INSERTED IN THE INLET RECEPTACLE, PUSHING FIRMLY ON THE WATER GRIP
AS SHOWN IN DIRECTION 2 TO LOCK THE WATER TANK.
8. FLUSHING OUT THE MACHINE
FILL WATER TANK TO MAXIMUM LEVEL.
PLUG IN THE APPLIANCE AND TURN IT ON.
THE LIGHTS ON THE CONTROL BUTTONS WILL
BEGIN BLINKING, THE LIGHTS IN USED-CAPSULE
CONTAINER IS LIGHTED IN BLUE WHICH GOES OFF
AFTER 1 MINUTE.
TIP: YOU CAN CHECK EASIER IF THE USED
CONTAINER IS FULL OR NOT WHEN THE BLUE LIGHT
IS ON.
THE BUTTON LIGHTS BECOME STEADY WHEN THE
MACHINE HAS HEATED UP. HEATING UP TIME IS 45
SECONDS APPROXIMATELY.

- 8 -
FLUSHING OUT THE MACHINE. (CONT.)
BEFORE PRESSING THE BUTTON, MAKE SURE THAT:
• THE HANDLE IS CLOSED WITHOUT COFFEE POD
INSIDE.
• THE WATER TANK IS FULL.
• THE WATER TANK IS FIRMLY IN PLACE,
OTHERWISE WATER MAY LEAK
• THE DRIP TRAY WITH THE USED COFFEE POD
CONTAINER IS COMPLETELY INSERTED (NEVER
OPERATE THE MACHINE WITHOUT DRIP TRAY
SET (PART D SHOWN IN “OVERVIEW OF
MACHINE PARTS AND CONTROLS”), OR HOT
WATER WILL RUN OUT WHEN OPENING
HANDLE.)
• A LARGE BOWL (250ML SIZE OR ABOVE) IS
PLACED UNDER THE DISPENSER.
PRESS THE LUNGO COFFEE BUTTON TO START FLUSH OUT.
• OPEN THE HANDLE WHEN THE FLUSH OUT PROCESS STOPPED
AUTOMATICALLY.
• EMPTY THE CUP.
• FLUSH OUT CYCLE IS FINISHED.
9. BREWING COFFEE
PLACE AN EMPTY CUP UNDER THE DISPENSER. FOR SMALL CUPS, PULL DOWN THE
DISPENSING SPOUT.
1. MOVE THE HANDLE UP AND BACK COMPLETELY.
2. INSERT AN ESE POD OR A CAPSULE (DEPENDING ON MODEL) INTO THE
COMPARTMENT CORRECTLY.
3. FOR ESE PODS, SLIDE BACK THE ESE POD COVER BEFORE INSERTING POD.
4. CLOSE THE HANDLE FIRMLY TO LOAD THE COFFEE ESE POD OR A CAPSULE.
5. PRESS THE DESIRED COFFEE BUTTON ONCE.
6. THE SELECTED BUTTON WILL BLINK AND THE MACHINE WILL BEGIN BREWING
COFFEE, DISPENSING WILL STOP AUTOMATICALLY WHEN REACHING THE
DEFAULT BREWING TIME.
7. RAISE THE HANDLE TO EJECT THE USED C ESE POD OR A CAPSULE INTO THE
CONTAINER.
8. CLOSE THE HANDLE.
TIP: WHEN USING THE MACHINE IN THE MORNING OR IF THE IDLE TIME LONGER THAN
1 HOUR), IT IS SUGGESTED THAT YOU BREW WATER FIRST IN ORDER TO REMOVE THE
RESIDUAL TASTE OF THE LAST CUP.
DEPENDING ON THE MODEL OF THE MACHINE INSERT EITHER A CAPSULE OR A POD.
ESE PODS FOR ESE MACHINES
NESPRESSO®* CAPSULES OR
CERTAIN COMPATIBLE CAPSULE FOR CAPSULE
MACHINE

- 9 -
10. REFILLING THE INTERNAL CIRCUIT WHEN WATER TANK IS OUT OF WATER DURING BREWING
IT IS STRONGLY RECOMMENDED THAT THERE IS ENOUGH WATER IN THE TANK BEFORE MAKING A COFFEE. THE MINIMUM LEVEL AT LEAST.
IN CASES WHERE THE WATER RUNS OUT DURING COFFEE BREWING IS COMPLETE, YOU CAN STOP THE BREWING PROCESS BY PRESSING THE SELECTED BUTTON WHICH IS BLINKING.
OPEN THE HANDLE TO EJECT THE USED CAPSULE. CAUTION: BEWARE OF HOT STEAM: DANGER OF SCALDING! FLUSH OUT THE MACHINE IN ACCORDANCE WITH “FLUSHING OUT
THE MACHINE”.
11. ENERGY SAVING MODE
THE MACHINE ENTERS ENERGY SAVING MODE AUTOMATICALLY ONCE THE MACHINE IS IDLE FOR 15 MINUTES. THE BUTTONS WILL FLASH CYCLICALLY IN ENERGY SAVING MODE. TO
QUIT ENERGY SAVING MODE, PLEASE PRESS ANY BUTTON, APPLIANCE WILL START TO WARM UP WITH LIGHTS BLINKING, WHEN THE BUTTONS ARE LIT STEADILY, THE MACHINE IS
READY TO BREW COFFEE.
12. PROGRAMMING THE COFFEE VOLUME
MAKE SURE THE WATER TANK IS IN PLACE BEFORE BREWING. DANGER OF SCALDING!
1. MOVE THE HANDLE BACK COMPLETELY.
2. INSERT AN ESE POD OR A CAPSULE (DEPENDING ON MODEL) INTO THE COMPARTMENT CORRECTLY.
3. CLOSE THE HANDLE FIRMLY TO LOAD THE COFFEE ESE POD OR A CAPSULE.
4. PRESS THE DESIRED BUTTON AND KEEP IT PRESSED DOWN, ONCE THE DESIRED VOLUME HAS BEEN REACHED, RELEASE THE BUTTON, NOW THE BUTTON IS REPROGRAMMED.
5. AFTER THE PROGRAMMING, THE SIZE WILL BE RECORDED IN MEMORY. FOR NEXT USE, BY CLICKING THE BUTTON NORMALLY (PRESS ONCE.)
DO THE SAME FOR OTHER BUTTONS IF REQUIRED.
VOLUME RANGE: CONTROLLED BY TIME FROM 13 S~ 90 S (25ML ~150ML BASED. DEFAULT TIME IS 25S FOR SMALL CUP AND 48S FOR LARGE CUP.
TIP: THE BLINKING FREQUENCY IS 1 SECOND 1 BLINK, HENCE, YOU CAN COUNT THE BLINKING TO WORK OUT THE BREWING TIME.

- 10 -
13. CLEANING
EMPTYING THE CAPSULE/POD CONTAINER AND DRIP TRAY.
1. THE CAPSULE/POD CONTAINER HOLDS APPROX. 10 USED CAPSULES/PODS. WE RECOMMEND EMPTYING
THE USED CAPSULE CONTAINER AND THE DRIP TRAY EVERY DAY. THE BLUE LIGHT INDICATES THAT THE
CAPSULE/POD CONTAINER IS FULL.
2. RAISE THE HANDLE TO ENSURE THERE IS NO CAPSULE INSIDE THE BREWING COMPARTMENT.
3. RAISE THE DISPENSING SPOUT UP IF IT IS IN LOW POSITION.
4. HOLD THE DRIP TRAY FIRMLY AND PULL IT OUT BY LIFTING GENTLY.
5. DISPOSE OF USED CAPSULES AND DRIP TRAY.
6. THE USED CAPSULE CONTAINER CAN BE DETACHED, IF NECESSARY, FROM THE LOWER DRIP TRAY (SNAP
LOCK).
7. RINSE OUT THE DRIP TRAY SET WITH FRESH WATER.
8. REMOVE THE WATER FROM THE APPLIANCE, RINSE OUT THE WATER TANK WITH FRESH WATER.
9. AFTER EMPTYING/CLEANING, REASSEMBLE THE PARTS IN REVERSE ORDER AND INSERT THEM BACK TO
MACHINE IN PLACE.
COFFEE MACHINE
1. ALWAYS PULL OUT THE POWER PLUG BEFORE CLEANING THE MACHINE.
2. NEVER IMMERSE THE MACHINE IN WATER OR CLEAN IT UNDER RUNNING WATER.
3. CLEAN THE MACHINE WITH A DRY CLOTH.
4. NEVER USE ABRASIVE CLEANING AGENTS OR MATERIALS (USE E.G. DRY RAGS OR KITCHEN PAPER).