G-Light Rinku-GLink RH-GGO-KIT User manual

Rinku-GLink Garage/Gate Opener Install Guide (RH-GGO-KIT)
1. RX-Receiver(white) x 1 pc
2. TX-Transmitter(black) x 1 pc
3. Posi-Tap Wire Taps x 2 pcs
CONTENTS
4. Double Side Adhesive
5. Plastic Ties
6. AC Adapter x 1 pc
12
White
Black
4 5
36
Tools needed: Phillips Screwdriver, Wire Stripper
Installation Overview – Receiver (to opener)
On the back of your garage door/gate opener motor you have two wires that run to your wall button switch that operates the
door. You will connect the two wires from the Receiver to these two terminals on the garage door motor. You will then plug
the AC Adapter to the outlet above your garage door opener motor.
Installation Overview – Transmitter (in car)
You will locate the two wires that are connected to your high beams. You will only need to connect the Transmitter to one of
your headlights. Choose the one with the most working space behind it. You will use the supplied wire connectors to tap into
those high beam wires. You will then mount the transmitter and secure the wiring with the provided plastic ties and adhesive.
Compatibility
The transmitter will work with virtually all cars, trucks, motorcycles, or any vehicle with a 12volt electrical system. Any
vehicle with a high beam that can be activated by pulling on the turn-signal stalk is compatible with this product.
activate the high beam.
The Receiver is compatible with most garage door and gate openers manufactured from 1983. There are a few
models manufactured from 2011-on that may not work, check our website for the latest incompatible models list.
‘2 and 2’ Simple Installation -
Just Two Wires to Your Car and Two Wires to Your Garage Door!
Follow wall button wires to locate
the terminal connection area of the
garage motor unit. It typically looks
like the below two types:
Installing the RX-Receiver Inside Your Garage
1. Disconnect/Unplug the power to garage door opener so it will not operate accidentally during installation.
2. Locate the terminals on the garage door motor that the two wires of the wall button switch connect to.
If you have more than two wires, you will need to decipher the two wires (one positive, one negative) that
operate the garage door. This information can be found in your garage door manual.
3. Connect the BLUE and BROWN wires from the Receiver to the garage door terminals.
Connect one wire to each of the two terminals (it does not matter which color wire goes to which terminal).
See diagrams below for common terminal types and sample wire connections.
4. Connect the AC Adapter to the Receiver and plug into a wall outlet.
5. The LED on the receiver should light up and stay GREEN.
6. Mount the Receiver in a location away from any moving parts of the garage door opener.
(Typical mounting point is on the metal support straps above garage opener motor)
7. Secure the Receiver Unit and wires with the provided plastic ties, avoiding any moving parts of the door/gate.
8. Restore power to your garage door opener.
9. Receiver Installation is complete!
>>> Continue to back side for the next step and operating instructions.
(I) Receiver (To Gate or Garage Opener) :
Wiring Instructions:
Connect to Power (AC Adapter):
Plug into standard 120v Home Wall Power Outlet.
Connect Signal output / input.
BLUE & BROWN wire:
To the two terminals on the garage/gate opener motor
that trigger the operation of the door.
The same terminals the wall button wires are
connected to.
LED
To AC Adapter Brown wire
Blue wire
Programming
Button
White Color
Unit
Receiver (RX)
V2.0F
G-Light:
PAGE 1 of 2

Installing the TX-Transmitter In Your Car
1. Be sure the Garage Door is in sight and all vehicles and any persons are away from the garage door during the
installation of the Transmitter.
2. Determine which headlamp has more working room behind it. The Transmitter can be installed on either headlamp.
3. Operate your high beam switch and observe which lights are the actual high beams. You will tap the two wires of
the Transmitter to the two wires that power the high beam.
4. If your high beam connector has more than 2 wires, refer to the diagram below to see if your headlight
connector/bulb code matches the below. Your highbeam bulb will have one of the numbers stamped on it.
If your high beam only has 2-wires, go on to step-5.
IMPORTANT: Only operate the garage door when it is in sight to prevent injury to people or property.
The door will activate a second after receiving the signal.
If you are still unable to activate the door, see our troubleshooting section on our website (www.rinkuhaus.com).
Operating range is up to 100ft (30meters) depending on vehicle and other physical obstructions.
3. Strip 3/8” (9.6mm)
Red wire from the Transmitter
4. Insert Wire & Tighten
End Cap of the Posi-Tap with
transmitter wires
5. Repeat Procedure for the Headlight Ground Wire to the TX Black Wire
1. Insert Wire
Headlight Power wire to be tapped
2. Tighten
The body of the Posi-Tap to lock
the wire in place
5. Once you have found the high beam wires, use the supplied Posi-Taps to connect to these two wires.
Tap Red wire from TX to the Highbeam Power wire. Tap Black wire from TX to the Highbeam Ground wire.
See diagram below on how to correctly secure the wire Posi-tap connectors.
When the Transmitter is activated, the LED will light up RED. The door will open or close.
7. Secure the Transmitter and all wiring away from any moving parts of your vehicle using plastic ties and the adhesive.
If you have a sealed back cover type headlamp, mount the Transmitter inside the headlamp and close the back cover.
Expanding your Rinkuhaus Kit
You can expand your Rinkuhaus world to multiple vehicles or doors. Additional Receivers and Transmitters are
available for purchase on our website (www.rinkuhaus.com).
Adding Receivers
The Rinkuhaus In-Car Transmitter can control up to 5 Receivers. This means that the one transmitter in your vehicle
Many homes have multiple garage doors or a property gate. Just add an additional receiver to those doors and
control them with the one transmitter already in your car.
Here is one possible example if you had multiple Rinkuhaus Receivers set up in your home:
For instance you have a vacation home or parents’ home and you add a Rinkuhaus Receiver to their garage door, you
Adding Transmitters
golf carts, etc.) that use a gate on your property, you can install a Transmitter on each of them and they can operate
the same door or gate that has the one Receiver already installed. Make life more convenient for your entire household
or business by adding a Transmitter to those vehicles!
NEED MORE HELP? Visit www.RINKUHAUS.com for more resources and helpful hints!
(II) Transmitter Installation (In Vehicle) :
Wiring Instructions:
Connect to Headlight Highbeam signal wire
(+12V power)
RED wire : Connect to Headlight Highbeam signal wire
power +12V
BLACK wire: Connect to Headlight Highbeam Ground
LED
Red Wire Black wire
Black Color
Unit
CONTINUED FROM PAGE 1:
Ver-PT1.0R
PROGRAMMING
>>> If you have just purchased this kit, no programming is necessary <<<
NOTE: The Transmitter(TX) is pre-programmed to the Receiver (RX) module in each kit f e.
(1). To enter programming mode, press and hold the button of the Receiver for 5 seconds. T RANGE.
(2). Trigger headlights desired number of times to register into RX within 60 seconds of entering programming mode.
Example: F to progr e.
Note: If progr conds of entering programming mode or if RX is pressed/released again, it will return
to standby and the LED will be GREEN.
(3). Once the RX has received the signal from the TX, the LED on the R YELLOW. The LED will turn GREEN to c rm programming.
(4). Every Receiver can accept up to 20 TX codes. The 21st register will replace the 1st registered. The 22nd will replace the 2nd registered, etc.
(5). Every Transmitter can tr erent codes b t
●To Erase ALL memory from the Receiver (RX):
(1). Disconnect power to the Receiver(RX) and reconnect.
(2). Dur conds of power connection, press and hold the RX’s program button for 20 seconds, then LED will quick D.
(3). Release the programmer button. LED will con s.
(4). When all memory has been erased, the LED will light GREEN and return to Standby mode.
●To delete a SINGLE memory from the Receiver (RX):
(1). Enter programming mode by pressing and holding the button of the RX for 5 seconds RANGE.
(2). Trigger headlights desired number of times of the register you want to erase within 60 seconds of entering programming mode.
Example: F to erase what was progr e.
Note: If progr conds of entering programming mode or if RX is pressed/released again, it will return
to standby and the LED will be GREEN.
(3). Once the RX has received the signal from the TX, LED on the R D. The LED will then turn GREEN to c rm the erase.
ERASING MEMORY
(III) Operating The System
PAGE 2 of 2
Transmitter (TX)
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may cause undesired operation.