GABOR MD-ASL15W User manual

MD-ASL15W /SPRING LOADED
MONITORMOuNT
For 15″ - 27″(38.1-68.6 cm) LCD desktop computer monitors
User Manual

2 Welcome
The Gabor MD-ASL15W mounts your 15″–27″(38.1–68.6 cm) LCD computer monitor. It
attaches to your desk via a built-in clamp, freeing up valuable desk space and enabling
personalized monitor placement for improved safety and comfort over conventional monitor
stands. The MD-ASL15W’s arm incorporates an internal mechanical spring system, which
is safer than the gas springs found in similar products. This spring-loaded arm functions
as a counterbalance to support your monitor in any position. Multiple points of articulation
provide a full range of motion, making it easy to adjust your monitor’s height, tilt, swivel,
and roll.
Thank you for
choosing Gabor.

3Welcome

4 Overview
Overview Mounting Arm (x1)
M4x12 (x8) M4x30 (x8)
M6x25 (x2)
13X5.5X16.5 (x8)
(x1)
S=3mm (x1)
S=5mm
A
B
(x2)
(x1)
M4x12 (x8) M4x30 (x8)
M6x25 (x2)
13X5.5X16.5 (x8)
(x1)
S=3mm (x1)
S=5mm
A
B
(x2)
(x1)
Tools Required For
Installation
• Phillips Screwdriver
VESA Mount
Locking
collar
Shaft
Mounting
socket
Cable guides
Clamp
Clamp screws
Clamp locking
knob
Set screw

5Overview
M4 Hex Key Spacer Cable Clip/
Protective Caps
Ax4
Bx4
Cx1
Dx1
Fx1
Gx1
Ex4
M4x12 (x8) M4x30 (x8)
M6x25 (x2)
13X5.5X16.5 (x8)
(x1)
S=3mm (x1)
S=5mm
A
B
(x2)
(x1)
M4x12 (x8) M4x30 (x8)
M6x25 (x2)
13X5.5X16.5 (x8)
(x1)
S=3mm (x1)
S=5mm
A
B
(x2)
(x1)
M4x12 (x8) M4x30 (x8)
M6x25 (x2)
13X5.5X16.5 (x8)
(x1)
S=3mm (x1)
S=5mm
A
B
(x2)
(x1)
A(4) M4 × 12 screw
B(4) M4 × 30 screw
C3 mm hex key
D5 mm hex key
E(4) Spacer
FCable clip
G(1) Shaft Cap
HUser Manual
Supplied Parts & Hardware
Also Included
F G
?
M4x12 (x8)
M4x30 (x8)
(x1)
M5x12 (x8)
M5x30 (x8)
13X5.5X16.5 (x8)
S=4mm (x1)
B CA
E
D
13" - 27"(33-69cm)
Max. 8 kg every screen
±15°
(Installed in shaft)

6
8
B
M6x25
A
S=5mm
12.2″ (31 cm)
90°
85°
180°
360°
0-13.8
″
(0-35 cm)
+/-45°
360°
Max. 16.1″ (41 cm)
Product Specifications
Monitor display size:
15″–27″(38.1–68.6 cm)
Maximum load capacity (per arm):
17 lb. (7.8 kg)
VESA standard: 75 × 75, 100 × 100
Tilt: -90°/+85°
Swivel: 180°
Roll: 360°
• Installation: Clamp fits desk edges up to
2.6″(6.5 cm) thick
•Arm width (extended): 28.7″(73 cm)
•Arm pivot: 180°
•Arm height adjustment
Angle: ±45°
Range: 0″–13.8″(0–35 cm)
•Shaft height: 12.2″(31 cm)
•Weight: 8.25 lb. (3.7 kg)
Specifications

7
Safety Warnings
Please read and follow the instructions and
keep this manual in a safe place.
Clean this product with only a soft, dry cloth.
Keep this product away from children.
Make sure everything is secure before
proceeding.
Make sure that this product is intact and
that there are no missing parts.
To avoid damage to this product, be careful
not to overtighten or improperly thread any
of the threaded fittings.
Do not exceed the maximum load capacity.
Do not install this product on an unsteady
structure or one that is prone to vibration,
has a chance of being impacted, or is
susceptible to other movements. Reinforce
the structure as necessary before installing
this product.
Mounting surfaces should be sturdy and flat.
Do not install this product on a weak, uneven
surface.
All photos are for illustrative purposes only.
17
2
8
9
10
3
4
5
6
Safety Warnings

8
GETTING STARTED:
Decide where you want to place your monitor. You'll be positioning your monitor directly in
front of you, at eye level, and approximately at an arm’s length away. You shouldn’t need to
turn your head to look at your monitor. If you have to strain to look at it, you should readjust
its position.
Getting Started

9Installation Instructions
ATTACHING THE SHAFT
• The MD-ASL15W easily
attaches to most desk
edges up to 2.6″(6.5 cm)
thick, even if your desk
is nearly flush against a
wall. Before attaching
the shaft to your desk,
determine whether
you have enough room
to fit the entire clamp
behind your desk. If you
have enough clearance
to attach the clamp
without removing the
bottom part of it, skip to
Clearance on this page.
• If your desk is close to
a wall or you don’t have
enough clearance to fit
the entire clamp behind
your desk, you can
remove the bottom part
of the clamp. If this is
the case, skip to Limited
Clearance on page 10 .
Clearance
1. Loosen the clamp locking
knob until you can fit the
clamp over the edge of
your desk.
2. Fit the clamp over the
edge of your desk, and
tighten the clamp locking
knob until the shaft is
securely mounted to
your desk.
• Continue with Attaching
Your Monitor to the VESA
Mounts on page 11 .

10
Limited Clearance
1. Use the included 5 mm
hex key to remove the
clamp screws.
2. Fit the top part of the
clamp behind your desk.
3. Underneath your desk,
align the screw holes in
the top and bottom parts
of the clamp.
• Note: It may help to
unscrew the clamp
locking knob first.
4. Reinsert the clamp
screws and use the
included 5 mm hex key
to fasten them until fully
tightened.
5. Tighten the clamp locking
knob until the shaft is
securely mounted to your
desk.
• Continue with Attaching
Your Monitor to the VESA
Mounts on page 11 .
Installation Instructions
A
M4x12
A
M4x12