Galanz GLEC02S3CT14 User manual

Thank you for purchasing a Galanz product. Please read this manual carefully for correct usage and safety,
and keep for future reference. For service, support and warranty information, call 800-562-0738.
@2021 Galanz Americas Limited Company@2021 Galanz Americas Limited Company
MODEL: GLEC02S3CT14
2-IN-1 ESPRESSO MACHINE & COFFEE MAKER
USER MANUAL

CONTENTS
CONTENTS
Important Safeguards
Getting To Know Your Espresso Machine
Preparing & Using Your Espresso Machine
Cleaning & Maintenance
Trouble Shooting
Product Warranty
Main Unit
Control Panel
Before first use
Espresso making guide
1
3
5
7
7
8

1 2
IMPORTANT SAFEGUARDS IMPORTANT SAFEGUARDS
IMPORTANT SAFEGUARDS IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety
precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE USING
YOUR Galanz 2-IN-1 ESPRESSO MACHINE &
COFFEE MAKER
Close supervision is necessary when any appliance is used by or
near children or individuals with certain disabilities.
To protect against electric shock, DO NOT PLACE ANY PART OF
THE ESPRESSO MACHINE IN WATER OR OTHER LIQUIDS.
Do not operate the appliance without water in the water tank.
Scalding may occur if the basket holder is opened during the
brewing cycle.
Do not let the cord hang over the edge of a table or counter, or
touch hot surfaces.
Do not operate the appliance with a damaged cord, plug, after the
appliance malfunctions or after it has been dropped or damaged
in any manner. Please contact us at 1-800-562-0738 for
troubleshooting and warranty support.
The use of accessory attachments not recommended by Galanz
may cause injuries.







Unplug from outlet when the appliance is not in use and before
cleaning. Allow it to cool before putting on or taking off parts, and
before cleaning the appliance.To unplug, grasp the plug and pull
from the outlet. Never pull from the power cord.
Do not clean with metal scouring pads. Pieces can break off the
pad and touch electrical parts, posing a risk of electric shock.
Do not use outdoors.
Do not use appliance for anything other than intended use.
This appliance is for HOUSEHOLD USE ONLY.
Do not touch hot surfaces. Use handles and knobs.
This appliance can be used by persons (including children) with
reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have supervision or instruction
concerning use of the appliance in a safe way and understand the
hazards involved.
Children should not play with the appliance.
For appliance with type Y attachment, if the supply cord is
damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified person in order to avoid a hazard.









Do not place on or near a hot gas or electric burner, or in a heated
oven.
Appliances are not intended to be operated by an external timer or
separate remote-control system.
WARNING: Risk of Fire or Electric Shock. Do not remove the
bottom cover. No user serviceable parts inside. Repair should be
done by authorized service personnel only.
Avoid contacting moving parts.




HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
Model No.
Power Consumption
Watts
Capacity
GLEC02S3CT14
120V, 60Hz
1450W
2 cups

3 4
GETTING TO KNOW YOUR ESPRESSO MACHINE GETTING TO KNOW YOUR ESPRESSO MACHINE
GETTING TO KNOW YOUR ESPRESSO MACHINE GETTING TO KNOW YOUR ESPRESSO MACHINE
1.Steam/Hot Water Dial:
To release steam or hot water.
2.Control Panel
3.Removable Water Tank :
For easy filling or discarding.
4.Reusable Filter
Holds coffee grounds and can be washed
after each use.
5.Removable Filter Holder:
For placing reusable filter or paper filter.
6.Group Head:
For easy positioning of the portafilter
7.Portafilter
Holds the coffee grounds prior to and
during the brewing process.
8.Steam Wand
Used to heat and froth milk.
9.Removeable Drip Tray
For easy cleaning.
10.1-Cup Espresso Filter Basket
11.2-Cup Espresso Filter Basket
12.Scoop and Tamper
Use to gather and pack the coffee grounds
allowing you to get the best shot of espresso.
6. Power Light
Illuminates when the machine is powered on
7. Pre-heat Light
Flashes when the machine is preheating and illuminates when it
finishes
8. Cup Size Light
Illuminates when corresponding espresso cup size is selected
9. Steam Light
Illuminates when the STEAM button is pressed
10. Hot Water Light
Illuminates when the Hot Water function is turned on
11. Drip Coffee Light
Illuminates when the DRIP COFFEE button is pressed and during the
brewing cycle
1. STEAM Button
Press to heat up water and generate steam
2. 1 CUP Button
Press to extract 1 standard cup of espresso
3. 2 CUPS Button
Press to extract 2 standard cups of espresso
4. ESPRESSO Button
Press to power on the machine and start heating up the espresso
module
5. DRIP COFFEE Button
Press to power on the machine and start brewing drip coffee
CONTROL PANEL
3 8
10
11
4/5
7
9
12
1
6
9
7
2
6
8
10
11
MAIN UNIT

5 6
PREPARING & USING YOUR ESPRESSO MACHINE PREPARING & USING YOUR ESPRESSO MACHINE
PREPARING & USING YOUR ESPRESSO MACHINE
MAINTENANCE & TROUBLE SHOOTING
BEFORE FIRST USE ESPRESSO MAKING GUIDE
MACHINE PREPARATION
INITIAL START UP
FLUSHING THE MACHINE
PREHEAT THE MACHINE




Ensure all packaging has been removed.
Position the machine onto a dry, stable, flat & horizontal
countertop.
Clean parts and accessories (water tank, portafilter, filter baskets
filter holder and steam wand) using warm water and a gentle
dishwashing liquid and rinse well. Wipe the outer housing and drip
tray with a soft damp cloth and dry thoroughly.
Do not immerse the outer housing, power cord or power plug in
water or any other liquid.
Fill the tank with water. Water level should not exceed the “MAX”
mark on the tank.
Insert the Power Plug into a 120V AC power outlet & switch the
power on.
When the PREHEAT light is illuminated, the machine is ready to
use.
Insert the filter basket into the portafilter, insert the portafilter flat
against the group head, and turn the portafilter right all the way to
the center position.
Put the Reusable Filter into the filter holder and insert it into the
drip coffee slot
It is recommended to complete a water flushing operation without
ground coffee to ensure the machine has been conditioned.
Press ESPRESSO and 2 CUPS, water should start flowing from
the portafilter. Allow water to run through until it stops.
Put a pitcher or jar under the drip coffee station and press DRIP
COFFEE. Water should start flowing from the filter holder. Allow
water to run through untill it stops

Open the water tank lid and pour cold, preferably filtered water into
the tank to the maximum mark on the side of the tank and slide the
water tank back into position at the back of the machine.

Switch the power on by pressing the ESPRESSO button. The
PREHEAT light will illuminate & pulse to indicate the thermoblock is
heating up. When the PREHEAT light stops flashing, the machine is
ready to use.

Tap the portafilter several times to distribute the coffee evenly in the
filter basket.
COFFEE DOSE AND TAMPING


Wipe the filter basket with a dry cloth before using to remove any
remaining coffee grounds.
Measure out enough coffee beans for 1 or 2 cups of espresso
(depending on your needs) then grind the beans in a coffee grinder
until they are a fine powder. You can also use pre-ground coffee
beans that have been ground for an espresso machine. Fill the filter
basket with the desired amount of coffee grounds.
FILL THE WATER TANK
NOTE:
Check the water level before using the machine and replace the water daily. The
water tank should be filled with fresh, cold tap water before each use. Do not use
de-mineralized or distilled water or any other liquid.
NOTE:
For a balanced taste, we recommend using 8-10g of coffee grounds for 1 cup and
15-18g of coffee grounds for 2 cups.
EXTRACTING ESPRESSO
FROTHING MILK


Tamp down firmly using the other end of the measuring scoop (using
approx. 30-40lbs or 15-20kg of pressure). It’s important to apply
consistent pressure every time.
Wipe excess coffee from the rim of the filter basket to ensure a
proper seal in the group head is achieved.



Insert the Portafilter into the Group Head & lock into position. Place
an espresso cup centered below the portafilter on the drip tray.
Press the 1 CUP or 2 CUPS button, a pumping noise will be heard.
After a few seconds, espresso will begin to brew into the cup.
Extraction will automatically stop when 1 cup (1 oz) or 2 cups (2 oz)
of espresso is brewed.





Press the ESPRESSO button and the STEAM button. The PREHEAT
light will start to flash indicating that the machine is heating up. When
the PREHEAT light stops flashing, the steam is ready.
It is recommended to purge the steam wand before inserting it into
the milk. Put the steam wand into an empty pitcher, turn the
Steam/Hot water Dial couterclockwise to purge the steam wand.
Discard any liquid that was purged into the pitcher.
Add milk to a mug or frothing pitcher, making sure to only fill half
way or less so that the milk has room to froth without over flowing.
Insert the wand into the milk and turn the Steam/Hot water Dial
counterclockwise.
To stop the steam, turn the Steam/Hot water Dial to the ‘OFF’
position and remove the steam wand from the mug or pitcher.
NOTE:
The steam function should only be used when the wand is inserted in milk. The
steam should always be turned off before removing the wand from the container of
milk.
HOT WATER



Press the ESPRESSO button and wait untill the PREHEAT light stops
flashing.
Place the steam wand into an empty mug. Turn the Steam/Hot
water Dial counterclockwise. Hot water will come out from the Steam
Wand.
Turn the Steam/Hot water Dial to OFF to stop the Hot Water function.
NOTE:
Steam and Hot Water functions cannot be operated at the same time.
DRIP COFFEE MAKING GUIDE

Open the water tank lid and pour cold, preferably filtered water into
the tank to the maximum mark on the side of the tank and slide the
water tank back into position at the back of the machine.
FILL THE WATER TANK
PUT THE COFFEE GROUNDS INTO THE FILTER
Draw the Filter Holder out from the machine. Pour your desired
amount of coffee grounds into the permeant filter holder or place a
paper filter in the holder and add grounds to that. Insert the Filter
Holder back into the machine.

NOTE:
It is recommended to put 21g of coffee grounds in order to brew a full single serve
size cup of drip coffee (around 300ml)
BREW COFFEE
Press the DRIP COFFEE button, the machine will be powered on and
will begin brewing cycle.
The brewing cycle will automatically stop when a full single serve size
cup of drip coffee is brewed (around 300ml).










7 8
MAINTENANCE & TROUBLE SHOOTING PRODUCT WARRANTY
PRODUCT WARRANTY
above exclusions will be denied. All liability is limited to the
purchase price and does not include any:
Retail offered extended warranties
Tax
Other charges(including postage to send required materials)
Incidental and/or consequential damages associated with the
product in question.
Every implied warranty, including any statutory warranty of
merchantability or fitness for a particular purpose is disclaimed
except to the extent prohibited by law, in which case such warranty
is limited to the duration of this written warranty. This warranty
gives you specific legal rights. You may have other legal rights that
vary depending on where you live. Some states do not allow
limitations on implied warranties or special, incidental, or conse-
quential damages, so the above limitations may not apply to you.
If you have a claim under this warranty, please call our Customer
Service number: 1-800-562-0738.
For faster service, please have the model number, serial number,
and receipt ready for the operator to assist you.

This warranty applies to products sold by Galanz Americas in the
U.S. This warranty is in lieu of any other warranty and expressly
applies to the individual product only.
Galanz product is warrantied for one year following purchase for
defects in material and workmanship. Please save your receipt
as proof of purchase is required to make a warranty
claim. During this warranty period, we will provide the replacement
cost of this product, a replacement of an equivalent product, or
repair per our discretion.
The warranty cannot be transferred through resale, including the
resale through a 3rd party unauthorized retailer and is only
bestowed upon the original consumer purchaser upon purchase
from an authorized retailer.
This warranty does not cover and excludes damage or
defects caused by:
Consumer misuse
Abuse
Neglect including the failure to clean and/or provide adequate
regular maintenance as outlined in the user manual
Commercial use
Subjecting the product to any voltage outside the specified
range
Loss of parts
The affixing of any attachments not provided with the product
Use in a manner not intended and outlined in the user manual
Any subsequent damages caused by the above listed exclusions
will not be covered and any claims determined to meet the
CLEANING ESPRESSO FILTER BASKET
CLEANING THE OUTER HOUSING
CLEANING THE DRIP TRAY
TROUBLE SHOOTINGCLEANING & MAINTENANCE
PROBLEM POSSIBLE CAUSE WHAT TO DO
Not enough espresso is
being extracted
Too much ground coffee in
the filter basket
Recommend using 8-10g of
coffee grounds for 1 cup and
15-18g of coffee grounds for
2 cups
Coffee tamped too firmly Recommend using approx.
30-40lbs or 15-20kg of
pressure
Too much water is being
extracted, espresso is light
in color and weak tasting
Not enough coffee grounds
in filter basket
Recommend using 8-10g
of coffee grounds for 1 cup
and 15-18g of coffee
grounds for 2 cups
Coffee not tamped firmly
enough
Recommend using approx.
30-40lbs or 15-20kg of
pressure
Espresso runs out around
the edge of the portafilter
Portafilter is not inserted into
the group head properly
Insert portafilter into the
group head and align with
‘LOCK’ on the group head
collar, until resistance is felt.
Refer to ‘EXTRACTING
ESPRESSO’, page 5
There are coffee grounds
around the filter basket rim
Too much ground coffee in
the filter basket
Clean any excess ground
coffee from the rim of the filter
basket to ensure a proper fit
into the group head
Recommend using 8-10g of
coffee grounds for 1 cup
and 15-18g of coffee
grounds for 2 cups
Steam/Hot Water function is
turned on
Machine is not powered on
after pressing ESPRESSO
button
Turn the Steam/Hot Water
Dial clockwise to close the
Steam function
Coffee tamped too firmly Recommend using approx.
30-40lbs or 15-20kg of
pressure
Water tank is empty or not
securely in place
Refer to ‘FILL THE WATER
TANK’ on page 4
Machine is making a loud and
continuous pumping noise
CLEANING THE STEAM WAND



Run steam to clear milk from the wand after frothing.
Allow the steam wand to cool completely before touching or
removing any parts.
Remove the steam wand and clean it under running water after each
use.


Discard any used coffee grounds from the portafilter after each use.
Be careful to only discard the coffee grounds and not the filter
basket.
Place the filter into the portafilter. Run water through the machine
with the filter and portafilter in place without any ground coffee.

The outer housing can be cleaned with a soft, damp cloth, and
polished with a soft, dry cloth. Do not use abrasive cleaners, pads or
cloths which can scratch the surface.

We recommend removing, emptying and cleaning the drip tray after
each use. Wash the drip tray with warm soapy water, using a
non-abrasive washing liquid. Rinse and dry thoroughly. The drip tray
base and cover are dishwasher safe.
NOTE:
Do not immerse power cord, power plug or appliance in water or any other liquid.
CLEANING REUSABLE FILTER BASKET

Discard any used coffee grounds from the resusable filter basket.
Rinse it under water and then allow it to air dry.
MAINTENANCE & TROUBLE SHOOTING

Please mail this warranty card to the address below within 30 days of purchase.
Galanz Americas, 55 Challenger Road, Suite 503, Ridgefield Park, NJ 07660.
PLEASE PRINT CLEARLY.
Name__________________________________________________________
Address________________________________________________________
City_______________________State___________Postal Code___________
Phone___________________Email___________________________________
Model Number_____________________Serial Number__________________
Purchase Location________________________________________________
You must attach a copy of your purchase receipt to validate your registration.
9
WARRANTY REGISTRATION
WARRANTY REGISTRATION