GALTRONICS 62-20-09 User manual

www.ga l tronics.com
Copyright © 2017 – Galtronics Corporation Ltd.
Proprietary Information. All rights reserved. Galtronics reserves the right to modify or amend any antenna or specifi cation without prior notice.
21-234-03 Release Date: 12th May, 2017; Revision: A;
Baylin TechnOlogies Company
Model No: 62-20-09 | Top Mounting Bracket on Pole for oDAS Antennas
18.7 lbs (8.5kg)
Specifications
Model Number
Weight
Dimensions:
Material
Wind Speed Resistance
Pole Diameter Range
62-20-09
Environmental Conditions Outdoor
7.5” x 7.8” X 20.5”
(190.5mm x 198.1mm x 520.7mm)
Carbon Steel
150MPh (241KMh)
Ø6” (152mm) to 12” (381mm)
Mounting Style Top Mount
Mounting Hardware to Antenna See Kit Below
Mounting Hardware to Pole Mount Not Included
Top Mounting Bracket on
Pole for oDAS Antennas
Antenna Installation
DESCRIPTION:
Galtronics top mounting bracket offers an easy installation for Galtronics’
oDAS Antennas of max Ø14.5” X 48” on poles with range of Ø6” to Ø12”
(Ø152mm to Ø381mm) or a wall.
PART IDENTIFICATION
7/16“ - Nut (8)
Stopper Plate(2)
7/16“ X 11/2” - Bolt (8)
Left Bracket (1)
Right Bracket (1)
5/16“ - Nylon Flange Lock Nut (2)
5/16“ - Cup Head Set Screw (2)
7/16“ - Plain Washer (16)
7/16“ - Spring Washer (16)
Support Bracket (1)
7/16“ X 11/2” - Bolt (8)
7/16“ - Nut (8)
7/16“ - Plain Washer (16)
7/16“ - Spring Washer (8)
5/16“ - Cup Head Set Screw (2)
5/16“ - Nylon Flange Lock Nut (2)
Support Bracket (1)
Left Bracket (1)
Right Bracket (1)
Stopper Plate(2)

21-234-03 Release Date: 12th May, 2017; Revision: A;
www.ga l tronics.com
Copyright © 2017 – Galtronics Corporation Ltd.
Proprietary Information. All rights reserved. Galtronics reserves the right to modify or amend any antenna or specifi cation without prior notice.
Baylin TechnOlogies Company
Model No: 62-20-09 | Top Mounting Bracket on Pole for oDAS Antennas
ASSEMBLY INSTRUCTIONS
Table 1.1 - Threaded rod length
Pole diameter: 8”
(203mm)
9”
(228mm)
11”
(279mm)
12”
(305mm)
6”
(152mm)
9”
(228mm)
7”
(177mm)
10”
(254mm)
11”
(279mm)
12”
(305mm)
10”
(254mm)
13”
(330mm)
14”
(255mm)
15”
(381mm)
Threaded rod length:
A. Attach support bracket to pole
Drill required hole (Ø 1.1”) through the
wooden pole (see drawing).
Attach the support bracket to the
wooden pole.
Our recommendation:
Use 1” threaded rods and corresponding 1”
plain washer, spring washers and 1″ Nut as shown
in the drawings.
Tighten with a torque of 150Nm (1328 In*Lbs).
Choose threaded rod length according to
Table 1.1.
7.8” (198.1mm)
20.5” (520.7mm)
11.6” (294.6mm)
8.5” (215.9mm)
7.5” (190.5mm)
8.5” (215.9mm)
1″Plain Washer
1″Sping Washer
1″Nut
4.3” (10.9mm)
6.9” (175mm)
Wooden Pole
(Ø6” to Ø12”)

21-234-03 Release Date: 12th May, 2017; Revision: A;
www.ga l tronics.com
Copyright © 2017 – Galtronics Corporation Ltd.
Proprietary Information. All rights reserved. Galtronics reserves the right to modify or amend any antenna or specifi cation without prior notice.
Baylin TechnOlogies Company
Model No: 62-20-09 | Top Mounting Bracket on Pole for oDAS Antennas
B. Assemble right bracket stopper plates and left bracket (Clamping brackets)
Use 7/16” fasteners to attach the support bracket,
stopper plates and left brackets without tightening (see details).
For a pole with diameter between 9” - 12”, position the interlock
tabs of the stopper plates towards the support
bracket (see picture detail on the left).
For 6” - 9” pole diameters position, the interlock tabs
away from the support backet.
Tightening hardware to the final position
will be done after placing the antenna
on the pole!
7/16“ X 11/2”
7/16“ X 11/2”
7/16“ Nut
7/16“ Plain and
Spring Washer
7/16“ Plain Washer
C. Antenna Mounting
D. Cup Head Screw Installation
Place the antenna rod on top of the pole and adjust the position
of the right bracket to the center of the pole. Tighten all bolts.
Install 5/16” cup head set screw and
tighten to the appropriate torque. Lock
the antenna rod using the nylon flange
locking hex nut. Tighten hex nut to 15Nm
(132In*Lbs).
E. Check Torque
After adjustment all loosened bolts
must be tightened with a torque of:
5/16˝- 15Nm (132In*Lbs)
7/16˝- 40Nm (354In*Lbs)
1˝- 150Nm (1328In*Lbs)
DO NOT REUSE LOCKING HEX NUT.
ONLY USE NEW LOCKING HEX NUTS
FOR ANTENNA MOUNTING ADJUSTMENTS.
5/16“ - Nylon Flange
Lock Nut (2x)
Antenna Rod / 1“ Mount Adapter Rod
5/16“ - Cup Head
Set Screw (2x)
UltraFlatIn-BuildingSISOAntenna[698-960MHz,1695-2700MHz]