DIMENSIONS
EFFECTS : Adjusts various effect options.
DZOOM MODE : Digitally zooms a desired section of the image.
IMAGE FREEZE : Holds the image displayed on screen.
D-EFFECT : Masks out strong backlighting to produce a clearer image.
VERTICAL FLIP : Flips the images along the x-axis.
MIRROR : Flips the image along the y-axis.
ROTATE : Rotates the image.
CONTRAST : Sets the contrast of the image.
SHARPNESS : Sets the amount of sharpness applied on the image.
COLOR ADJUST : Used to tune the general color of the image.
COLOR : Toggles the color on or off.
COLOR LEVEL : Sets the color level of the image; the higher the level the
stronger the color.
COLOR HUE : Sets the hue of the image.
RED GAIN : Sets the amount of red gain applied on the image.
BLUE GAIN : Sets the amount of blue gain applied on the image.
SPECIAL : Adjusts various special options.
MOTION DET : Adjust motion detection settings. There is a initialization period of
~15sec. *Requires the alarm relay option.
ZONE NUMBER : Selects the current motion zone.
ZONE STATE : Toggles the motion zone on or off.
WIDTH : Sets the width of the motion zone.
HEIGHT : Sets the height of the motion zone.
MOVE X : Moves the motion zone horizontally.
MOVE Y : Moves the motion zone vertically.
SENSITIVITY : Adjusts the sensitivity of motion detection.
PRIVACY MASK : Used to hide regions of the image.
MASK NUMBER : Selects the current mask number
MASK STATE : Toggles the mask on or off.
MASK COLOR : Selects the desired mask color.
WIDTH : Sets the width of the mask.
HEIGHT : Sets the height of the mask.
MOVE X : Moves the mask horizontally.
MOVE Y : Moves the mask vertically.
LANGUAGE : Sets the desired OSD language.
(ENGLISH, GERMAN, SPANISH, FRENCH, RUSSIAN, POLISH).
STABILIZER : Used to digitally stabilize an image effected by wind/vibration.
L/L SYNC : Sets the desired line lock method.
INT : Uses the internal system to synchronize a line lock.
L/L : Uses the power signal to synchronize a line lock. *Requires the dual
voltage option.
MONITOR TYPE : Sets the video output to three main input types.
CRT : Best used for CRT monitors.
LCD : Best used for LCD monitors.
LIN : Best used for input types that require no gamma correction.
FACTORY RESET : Resets all settings to it’s factory defaults.
COMM SET : Used to configure the RS-485 port. *Requires the RS-485 option.
PROTOCOL : Only 1 protocol supported at the moment (Pelco-D)
CAMERA ID : Sets the ID for the RS-485 (0~255).
BAUD RATE : Sets the baud rate for the RS-485 (4800~57600).
SAVE/REBOOT : Activates the new settings and reboots the camera.
CAM NAME : Adjusts camera title settings.
OFF : The camera name will not be displayed onscreen.
ON : Press [Set] to access the submenu.
Enter the desired camera name, select [POS] to select the desired position,
then select [END] to exit and apply the changes.
LENS : Controls various settings related to the lens.
DC IRIS : Used with DC auto iris lens.
BRIGHTNESS : Adjusts image brightness.
REACTION SPEED : Adjusts the iris reaction speed.
MANUAL : Used with manual lens.
BRIGHTNESS : Adjusts image brightness.
EZ FOCUS : Temporary mode used to focus the lens.
EXPOSURE : Adjusts exposure settings.
AGC : Adjusts the AGC level.
SHUTTER : Sets the desired shutter option.
SENS-UP : Sets the desired multiple of the digital exposure length.
LOW LIGHT GAIN : Sets the amount of digital gain to use within the system.
DAY / NIGHT : Adjust Day / Night options.
AUTO : Automatically determines the D/N switching points.
D/N LEVEL : Adjusts the switching point level.
DWELL TIME : Adjusts the calculation time for the trigger.
NIGHT BURST : Enables night burst when in B/W mode.
COLOR : Color mode.
B/W : B/W mode.
CDS : Uses the CDS sensor to determine the switching point (IR Products)
LSC MODE : Toggles the LSC mode on or off.
LSC LEVEL : Adjusts the intensity of the LSC mode.
WDR / BLC / HLC : Adjusts backlight options.
WDR : Uses a true wide dynamic range algorithm to balance dark and over saturated
areas within the image.
WDR LEVEL : Adjusts the WDR level.
BLC : Produces a clearer image of an object darkened by strong backlighting.
BLC LEVEL : Adjusts the BLC level.
HLC : Masks out strong backlighting to produce a clearer image.
AREA SETTING : Sets which areas will be active for the HLC feature.
ALL AREA SET : Sets all areas active.
MASK COLOR : Sets the desired color of the masked area.
HLC LEVEL : Adjusts the level of masking.
GAIN CONTROL : Sets when the HLC will be active.
WHITE BAL : Adjusts white balancing options.
ATW1 : Automatically white balances the image.
ATW2 : Automatically white balances the image and compensates for some color
rolling.
AWC-SET : Press [SET] to white balances the image to a specific light environment.
This mode will not adjust to a new light environment.
MANUAL : Select ATW1 or AWC-set then enter the MANUAL white balancing mode to
manually adjust the scene to your desired settings.
3D-DNR : Reduces the background noise caused by the digital enhancement
of a low light environment. If AGC is turned OFF, the 3D-DNR will be disabled.
DNR LEVEL : Sets the level of noise reduction; the higher the level the less the noise.
DNR BLACK LEVEL : Sets the low light environment black level; the higher the level the
brighter the image. Please note that decreasing the DNR BLACK LEVEL too
much will result in the low light
GLOBAL MOVEMENT: Used to reduce a trailing effect caused by motion.
OSD MENU FUNCTIONS
