Gardco PureForm P26 User manual

PureForm / EcoForm
P26, P34, & ECF2
Area Luminaire
1/29/2019 page 1 www.gardcolighng.com PN 442294663261 Rev A
PureForm & EcoForm Luminaire Mounted on PTF2 (3-1/2” O.D.), PTF3 (4-1/2” O.D.) or PTF4
(5.00” O.D.) Pole Top Fier
STRAIN RELIEF ROD
SUPPLY & GROUND
WIRES
TAPE OR WIRE TIE
3/8-16 X 1.75” BOLTS
(2) #10-32 PHILLIPS PAN HEAD SCREWS
3/8” HEX NUT AND SPLIT LOCK WASHER
SPLIT LOCK WASHER AND FLAT WASHER
FITTER STOP
ARM COVER
(4) #8-32 PHILLIPS FLAT HEAD SCREWS
PTF2
PTF3/PTF4
POLE TOP
FITTER CAP
STRAIN RELIEF ROD
SUPPLY & GROUND
WIRES
TAPE OR WIRE TIE
3/8-16 X 1.75” BOLTS
(8) 3/8” SOCKET
SET SCREWS
(2) #10-32 PHILLIPS PAN HEAD SCREWS
3/8” HEX NUT AND SPLIT LOCK WASHER
FITTER STOP
ARM COVER
(2) #8-32 PHILLIPS PAN
HEAD SCREWS
FIG. 1
FIG. 2
SAFETY CABLE
SAFETY CABLE
LUMINAIRE LEADS
LUMINAIRE LEADS
SPLIT LOCK WASHER AND FLAT WASHER
POLE TOP
FITTER CAP
(8) 3/8” SOCKET
SET SCREWS

1/29/2019 page 2 www.gardcolighng.com PN 442294663261 Rev A
Pole with Tenon (See Table)
TENON HEIGHT
FITTER
TYPE
PTF2
PTF3
PTF4
"X"
DIA. (Ø)
3-1/2"
4-1/2"
5"
2-3/8" TO 2-1/2" O.D. X 4" HIGH
3" TO 3-1/2" O.D. X 6" HIGH
3-1/2" TO 4" O.D. X 6" HIGH
USED ON TENON SIZE
FIG. 3
1. Open Arm Cover by loosening (2) #8-32 Phillips Pan Head Screws located on boom of mounng arm (screws are capve and will re-
main on door). Door is aached to arm with a safety cable and can be removed if necessary. (See Fig. 1 & 2)
2. Aach luminaire/arm assembly to Pole Top Fier by lining up the threaded hole on PTF to boom hole on Arm.
3. Thread the boom 3/8” bolt, lock washer, and at washer into the lower tapped hole of the PTF from the inside of arm assembly and
ghten. (See Fig. 1,2 & 4)
4. Pass the top 3/8” bolt, lock washer, and at washer through the arm and into the top hole of the PTF. Secure with 3/8” lock washer
and hex nut. Torque both bolts to approximately 45 FT.-LBS.
5. Install the Pole Top Fier/Luminaire onto the Tenon. Top of the tenon must seat against the er stop. Level and secure with (8) 3/8”
socket set screws. Torque to approximately 20 FT.-LBS.
6. Install strain relief rod through two holes in top of er, and route supply and ground wires over the strain relief rod. Tie o with tape
or wire e as shown.
7. Connect eld supply and ground wires to luminaire leads. Make wire connecons per NEC or applicable local codes. Secure with wire
e.
8. Install PTF Cap and secure in place with (2) #10-32 Phillips Pan Head Screws.
9. Install Photo Control in housing if used.
10. Close Arm Assembly Cover and secure with (2) #8-32 Phillips Pan Head Screws.
11. Apply a bead of suitable weatherproof sealant to horizontal top, vercal le and right edges of Arm where it contacts the pole to pre-
vent water entry. (See Figure 5)
12. Energize Luminaire to test installaon.
FIG. 4
PTF2 PTF3/PTF4
PureForm & EcoForm Luminaire Mounted on PTF2 (3-1/2” O.D.),
PTF3 (4-1/2” O.D.) or PTF4 (5.00” O.D.) Pole Top Fier

1/29/2019 page 3 www.gardcolighng.com
© 2019 Signify Holding. All rights reserved. This document may be subject to change.
No representaon or warranty as to the accuracy or completeness of the informaon
included herein is given and any liability for any acon in reliance thereon is disclaimed.
All trademarks are owned by Signify Holding or their respecve owners.
Signify North America Corporaon
200 Franklin Square Drive,
Somerset, NJ 08873
Telephone [phone]
Signify Canada Ltd.
281 Hillmount Road,
Markham, ON, Canada L6C 2S3
Telephone [phone]
PN 442294663261 Rev A
ADD SILICONE TO
THESE AREAS
FIG. 5
PureForm & EcoForm Luminaire Mounted on PTF2 (3-1/2” O.D.),
PTF3 (4-1/2” O.D.) or PTF4 (5.00” O.D.) Pole Top Fier