Garden Furniture Direct Askham Tool Store Quick start guide

1
Before you commence the assembly process we recommend that you read these instructions
thoroughly beforehand to familiarise yourself with the assembly process and to also check that you have
the correct components. If for any reason you need assistance, you can find our contact details on the
final page of these instructions.
We highly recommend that any assembly is carried out on a flat, level surface if possible and that you
use another person to assist you if necessary.
Package contents
Tools required
2 x End panels
1 x Back panel
1 x Base
1 x Floor
1 x Roof
1 x Door
65mm screws
12 x 85mm screws (for the base only)
2 x Spacer blocks
Electric screwdriver with No2 Pozidrive bit
Or No2 Pozidrive Screwdriver
Askham Log Store
GaGarden
rnitu reFuu
Direct
T: 03333 448 121
ASSEMBLY
INSTRUCTIONS
Askham/Kendal 6/4ft
tool store

Askham/Kendal 6/4ft tool store
2
Step 1
Step 2
Ensure that you have all of the correct parts as listed
on the front page of these instructions, including any
fixings.
Stand the left hand end panel (or right hand for the
reversed roof version) upright on a flat, level surface.
Step 3
Step 4
Arrange the 2 spacer blocks on the ground, adjacent
to the end panel as shown in the photo above. Now
place a back panel on the blocks, at 90° to the end
panel, aligning the 2 panels ready for fixing.
Using the 65mm screws provided, attach the batten
on the back panel to the post of the end panel,
ensuring that the batten remains vertically aligned to
the post.

Askham/Kendal 6/4ft tool store
3
Step 5
Step 6
Remove the blocks from beneath the back panel and
then slide the base into position as shown so that it
locates in the gaps in the side panel battens.
Now add the right end panel, again locating the base
in the gaps in the side panel battens.
Step 7
Step 8
Secure the right side panel in place with 65mm
screws.
Attach the base to the end panel front posts using 2
of the 85mm screws for each side.

Askham/Kendal 6/4ft tool store
4
Step 9
Step 10
Now attach the base to the end panel rear posts,
again using 2 of the 85mm screws for each side.
Lay the floor section in the base and then gently
lower the roof into place as shown.
Step 11
Step 12
Check that the front batten ends sit flush with the
posts as shown. Now attach the roof to each end
panel post with 65mm screws.
Secure the rear of the roof using 65mm screws as
shown. Your log store is now complete. If your log
store came with doors, proceed to step 13.

Askham/Kendal 6/4ft tool store
5
Step 13
Step 14
Place a spacer block at the front of the log store
adjacent to the front end post and rest the hinge side
of the appropriate door on the block, aligning it
vertically and horizontally for a good fit. Now use four
of the supplied black hinge screws to affix the hinge
to the post.
Align the top hinge in place, ensuring that the gap
between the door and post is consistent at top and
bottom then secure the top hinge in place using more
of the black hinge screws
Step 15
Step 16
To fit the latch keeper plate, shut the door and hold
the latch in the horizontal position. Now fit the
keeper and mark its correct fixing position on the
post using a pencil or bradawl before securing it in
place using the screws provided.
Your Askham/Kendal tool store is now complete.
GardenFurniture.Direct i a trading tyle of LTK Sco Limited
Regi tered in England & Wale - Regi tered No. 6282947
We hope that you found your product quick and ea y to a emble.
However, if you require any further a i tance or have any que on you can
contact u by telephone on: 03333 448 121 or vi it www.gardenfurniture.direct