Garmin DEZLCAM OTR710 User manual

DĒZLCAM™OTR710 / LGV710
Owner’s Manual

© 2022 Garmin Ltd. or its subsidiaries
All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or
improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to
www.garmin.com for current updates and supplemental information concerning the use of this product.
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These trademarks may not be used without the express
permission of Garmin.
dēzlCam™, Garmin eLog™, Garmin Express™, and myTrends™ are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of
Garmin.
Android™ is a trademark of Google LLC. Apple®, iPhone®, and Mac® are trademarks of Apple Inc, registered in the U.S. and other countries. The BLUETOOTH® word mark and logos
are owned by the Bluetooth SIG, Inc. and any use of such marks by Garmin is under license. Love's® and Love's Travel Stops® are registered trademarks of Love's Travel Stops &
Country Stores, Inc. microSD® and the microSDHC logo are trademarks of SD-3C, LLC. Pilot Flying J™ and Pilot Flying J Travel Centers™ are trademarks of Pilot Travel Centers LLC
and its affiliate companies. PrePass® is a trademark of the PrePass Safety Alliance. Tripadvisor® is a registered trademark of TripAdvisor LLC. TruckDown® is the trademark of
TruckDown Info International, Inc.Wi‑Fi® is a registered mark of Wi-Fi Alliance Corporation.Windows® is a registered trademark of Microsoft Corporation in the United States and other
countries.

Table of Contents
Getting Started................................. 1
dēzlCam Device Overview...................... 1
Installing the Dash Camera Memory
Card.......................................................... 2
Mounting Considerations....................... 2
Mounting and Powering the dēzlCam
Device in Your Vehicle.........................3
Turning the Device On or Off.................. 6
Acquiring GPS Signals............................ 6
Status Bar Icons...................................... 7
Using the On-Screen Buttons................. 7
Adjusting the Volume..............................7
Using the Audio Mixer......................... 8
Enabling or Disabling Sounds and
Audio Sources..................................... 8
Adjusting the Screen Brightness............ 8
Vehicle Profiles................................ 8
Adding a Vehicle Profile..........................8
Adding an Environmental Zone Vehicle
Profile................................................... 9
Car Profile................................................ 9
Switching the Vehicle Profile.................. 9
Changing Your Trailer Information.........9
Editing a Vehicle Profile.......................... 9
Dash Cam....................................... 10
Aligning the Camera............................. 10
Dash Cam Recording............................ 10
Saving a Dash Cam Recording......... 10
Stopping or Starting Dash Camera
Recording........................................... 10
Turning Audio Recording On or Off.. 11
Viewing Videos and Photos................. 11
Videos on Your Computer.................... 11
Deleting a Video or Photo..................... 11
Vault Storage......................................... 11
Upgrading Your Vault Subscription.. 11
Sharing a Video................................. 12
Editing and Exporting a Video.......... 12
Disabling a Shared Video Link.......... 12
Removing a Video from the Vault.... 12
Driver Awareness Features and
Alerts............................................. 13
Enabling or Disabling Driver Alerts.......13
Red Light and Speed Cameras............. 14
Advanced Driver Assistance System... 14
Forward Collision Warning System.. 14
Lane Departure Warning System......15
Finding and Saving Locations......... 16
Finding a Location Using the Search
Bar.......................................................... 17
Finding an Address............................... 17
Location Search Results....................... 18
Changing the Search Area.................... 19
Points of Interest...................................19
Finding Trucking Points of Interest.. 19
Finding TruckDown® Points of
Interest............................................... 19
Finding a Location by Category........ 20
Tripadvisor......................................... 20
Navigating to Points of Interest Within
a Venue.............................................. 20
Custom Points of Interest.................... 20
Installing POI Loader......................... 21
Finding Custom POIs........................ 21
Search Tools..........................................21
Finding an Intersection..................... 21
Finding a Location Using
Coordinates....................................... 21
Parking................................................... 21
Finding Truck Parking....................... 21
Finding Truck Parking in Europe...... 21
Finding Parking Near Your Current
Location............................................. 22
Finding Parking Near a Specified
Location............................................. 22
Viewing Recently Found Locations...... 22
Clearing the List of Recently Found
Locations........................................... 22
Viewing Current Location
Information............................................ 22
Finding Emergency Services and
Fuel..................................................... 22
Getting Directions to Your Current
Location............................................. 22
Saving Locations................................... 23
Saving a Location.............................. 23
Saving Your Current Location........... 23
Editing a Saved Location.................. 23
Table of Contents i

Assigning Categories to a Saved
Location............................................. 23
Deleting a Saved Location................ 23
Navigating to Your Destination....... 24
Routes.................................................... 24
Starting a Route.....................................24
Starting a Route by Using the Map...24
Going Home....................................... 24
Your Route on the Map......................... 25
Viewing Popular Truck Paths on the
Map.................................................... 26
Active Lane Guidance....................... 26
Viewing Turns and Directions...........26
Viewing the Entire Route on the
Map.................................................... 26
Planning Your Arrival............................ 26
Arriving at Your Destination................. 27
Completing a Truck Route................ 27
Parking Near Your Destination......... 28
Changing Your Active Route.................28
Adding a Location to Your Route..... 28
Shaping Your Route...........................28
Taking a Detour................................. 28
Changing the Route Calculation
Mode.................................................. 29
Stopping the Route............................... 29
Using Suggested Routes...................... 29
Avoiding Delays, Tolls, and Areas........ 29
Avoiding Traffic Delays on Your
Route.................................................. 29
Avoiding Road Features.................... 29
Avoiding Environmental Zones On
Your Route......................................... 29
Custom Avoidances.......................... 29
Using the Map................................ 30
Map Tools.............................................. 31
Viewing a Map Tool...........................31
Up Ahead............................................... 31
Viewing Upcoming Locations........... 32
Customizing the Up Ahead
Categories..........................................32
Cities Ahead.......................................... 32
Viewing Upcoming Cities and Exit
Services..............................................32
Warning and Alert Symbols.................. 32
Restriction Warnings......................... 33
Road Condition Warnings................. 33
Alerts.................................................. 34
Trip Information.................................... 34
Viewing Trip Data from the Map...... 34
Viewing the Trip Information Page.. 34
Resetting Trip Information................35
Viewing Upcoming Traffic.................... 35
Viewing Traffic on the Map.............. 35
Searching for Traffic Incidents......... 35
Customizing the Map............................ 35
Customizing the Map Layers............ 35
Changing the Map Data Field........... 35
Changing the Map Perspective........ 36
Live Services, Traffic, and
Smartphone Features..................... 36
Pairing with Your Smartphone............. 36
Disabling Bluetooth Features
(Android™)..........................................36
Disabling Bluetooth Features
(iPhone®)...........................................37
Viewing Videos and Photos on Your
Smartphone........................................... 37
Deleting a Video or Photo Using Your
Smartphone....................................... 37
Bluetooth Feature Status Icons............37
Smart Notifications............................... 38
Receiving Notifications..................... 38
Viewing the List of Notifications...... 39
Going to an Address or Location Using
the dēzl App........................................... 39
Hands-Free Calling................................ 39
Placing a Call..................................... 39
Receiving a Call................................. 40
Using the Call History........................40
Using In-Call Options......................... 40
Saving a Home Phone Number........ 40
Deleting a Paired Phone....................... 41
Traffic............................................ 41
Receiving Traffic Data Using Your
Smartphone........................................... 41
Enabling Traffic..................................... 41
Viewing Traffic on the Map.................. 41
Searching for Traffic Incidents......... 41
ii Table of Contents

Vehicle and Driver Tools................. 42
Break Planning...................................... 42
Taking a Suggested Break................ 42
Starting the Break Timer................... 42
Pausing and Resetting the Break
Timer.................................................. 42
Adjusting Drive Hours....................... 42
Adjusting the Daily Driving Limit...... 42
Garmin eLog.......................................... 43
Setting Up Garmin eLog Features On
Your dēzl Device................................ 43
Viewing Garmin eLog Information on
Your dēzl Device................................ 43
Viewing Garmin eLog Diagnostic and
Malfunction Events........................... 43
IFTA........................................................ 43
Entering Fuel Data............................. 44
Editing Fuel Data............................... 44
Viewing and Exporting a Jurisdiction
Summary............................................ 44
Editing and Exporting Trip Reports.. 44
Viewing Exported Jurisdiction
Summaries and Trip Reports............ 45
Logging Service History........................ 45
Adding Service Categories............... 45
Deleting Service Categories..............45
Renaming Service Categories.......... 45
Deleting Service Records.................. 45
Editing a Service Record................... 46
PrePass®...............................................46
Loyalty Programs.................................. 46
Using the Apps............................... 46
Viewing the Owner's Manual on
Your Device............................................46
Viewing the Weather Forecast............. 46
Viewing Weather Near a Different
City..................................................... 46
Viewing the Weather Radar.............. 47
Viewing Weather Alerts.....................47
Checking Road Conditions............... 47
Route Planner........................................ 47
Planning a Route............................... 47
Editing and Reordering Locations in a
Route.................................................. 48
Changing Routing Options for a
Route.................................................. 48
Navigating to a Saved Route............ 48
Editing and Saving Your Active
Route.................................................. 48
photoLive Traffic Cameras................... 48
Viewing and Saving photoLive Traffic
Cameras.............................................49
Viewing photoLive Traffic Cameras on
the Map.............................................. 49
Saving a Traffic Camera................... 49
Wireless Cameras................................. 49
Pairing the BC 40 Camera with a
Garmin Navigation Device................ 49
Pairing a BC 50 Camera with a Garmin
Navigation Device............................. 50
Viewing the Backup Camera............ 50
Viewing Previous Routes and
Destinations.......................................... 51
Music Player.......................................... 52
Adding the Music Player Tool to the
Map.................................................... 52
Garmin PowerSwitch™ App.................. 53
Activating a Power Switch................ 53
Turning Off All Switches................... 53
Customizing a Button....................... 54
Assigning a Switch to a Control
Input................................................... 54
Adding a Custom Layout.................. 54
Routines............................................. 55
Voice Command............................. 56
Tips for Speaking to the Device........... 56
Launching Garmin Voice-Activated
Navigation............................................. 57
Controlling the Camera Using Voice
Commands............................................ 57
Checking Your Arrival Time.................. 57
Placing a Phone Call Using Your
Voice...................................................... 57
Changing Device Settings Using Your
Voice...................................................... 57
Settings..........................................57
Map and Vehicle Settings..................... 57
Enabling Maps................................... 58
Navigation Settings............................... 58
Calculation Mode Settings............... 58
Setting a Simulated Location........... 58
Wireless Network Settings................... 59
Table of Contents iii

Driver Assistance Settings................... 59
Proximity Alerts Settings.................. 59
Dash Cam Settings............................... 60
Backup Camera Settings...................... 60
Display Settings.....................................60
Traffic Settings...................................... 60
Units and Time Settings....................... 60
Setting the Time................................ 61
Language and Keyboard Settings........ 61
Device and Privacy Settings................. 61
Resetting Data and Settings............. 61
Device Information......................... 61
Viewing E-label Regulatory and
Compliance Information....................... 61
Specifications........................................62
Charging the Device.............................. 62
Device Maintenance....................... 62
Garmin Support Center......................... 62
Map and Software Updates.................. 62
Connecting to a Wi‑Fi Network......... 62
Updating Maps and Software Using a
Wi‑Fi Network.................................... 63
Updating Maps and Software with
Garmin Express................................. 64
Device Care............................................65
Cleaning the Outer Casing................ 65
Cleaning the Touchscreen................ 65
Cleaning the Camera Lens................66
Avoiding Theft................................... 66
Restarting the Device............................ 66
Removing the Device, Mount, and
Suction Cup........................................... 66
Removing the Device from the
Mount................................................. 66
Removing the Mount from the Suction
Cup..................................................... 66
Removing the Suction Cup from the
Windshield......................................... 66
Data Management.......................... 66
About Memory Cards............................ 66
Formatting the Dash Cam Memory
Card........................................................ 67
Connecting the Device to Your
Computer............................................... 67
Transferring Data From Your
Computer............................................... 67
Disconnecting the USB Cable...............67
Troubleshooting............................. 67
My video recordings are blurry............. 67
My memory card has degraded and
needs to be replaced............................ 68
My video recordings are choppy or
incomplete............................................. 68
The suction cup will not stay on my
windshield..............................................68
My device is not acquiring satellite
signals....................................................68
The device does not charge in my
vehicle.................................................... 68
My battery does not stay charged for
very long................................................ 69
My device does not connect to my
phone..................................................... 69
Appendix........................................ 69
Installing a Memory Card for Maps and
Data........................................................ 69
Viewing GPS Signal Status................... 69
Purchasing Additional Maps................ 69
Purchasing Accessories....................... 69
European Emission Standards............. 69
Garmin PowerSwitch............................ 70
Mounting Considerations................. 70
Mounting the Device......................... 70
Opening the Front Cover................... 71
Connecting Accessories................... 72
Connecting a Control Input............... 73
Connecting the Device to Vehicle
Power................................................. 73
Pairing with a Garmin Navigation
Device.................................................74
Garmin PowerSwitch
Specifications.................................... 74
Troubleshooting................................ 74
iv Table of Contents

Getting Started
WARNING
See the Important Safety and Product Information guide in the product box for product warnings and other
important information.
• Update the maps and software on your device (Map and Software Updates, page 62).
• Mount the device in your vehicle and connect it to power (Mounting Considerations, page 2).
• Acquire GPS signals (Acquiring GPS Signals, page 6).
• Adjust the volume (Adjusting the Volume, page 7) and display brightness (Adjusting the Screen Brightness,
page 8).
• Set up a vehicle profile (Adding a Vehicle Profile, page 8).
• Navigate to your destination (Starting a Route, page 24).
dēzlCam Device Overview
Microphone for Voice Command or hands-free calling
Power button
USB power and data port
Camera memory card slot
Map and data memory card slot
Getting Started 1

Installing the Dash Camera Memory Card
Before the device can record video from the integrated dash camera, you must install a camera memory card.
The camera requires a microSD® memory card from 4 to 256 GB with a speed rating of Class 10 or higher. You
can use the included memory card, or you can purchase a compatible memory card from an electronics
supplier.
NOTE: A memory card is included so your device is ready to use out of the box. All memory cards have a limited
life and must be replaced periodically. Your device alerts you when the memory card has exceeded its useful life
and needs to be replaced. You can follow the troubleshooting tips to help extend the useful life of the memory
card (My memory card has degraded and needs to be replaced, page 68).
1Insert a memory card into the camera memory card slot .
NOTE: If you install the memory card into the incorrect slot, the camera cannot record video.
2Press it in until it clicks.
Mounting Considerations
• Do not mount the device in a location that obscures the driver's view of the road.
WARNING
It is your responsibility to ensure the mounting location complies with all applicable laws and ordinances, and
does not block your view of the road during the safe operation of your vehicle.
• Choose a location that allows you to route the power cable safely.
WARNING
When installing the device in a vehicle, install the device and power cable securely so they do not interfere
with the vehicle operating controls. Interference with the vehicle operating controls can result in a collision,
which could result in injury or death.
• Choose a location that is within easy reach.
• Choose a location that provides the dash cam with a clear view of the road.
You should verify the vehicle's windshield wipers clear the windshield area in front of the dash cam, and you
should avoid placing the dash cam behind a tinted area of the windshield.
• Thoroughly clean the windshield before installing the mount.
2 Getting Started

Mounting and Powering the dēzlCam Device in Your Vehicle
WARNING
This product contains a lithium-ion battery. To prevent the possibility of personal injury or product damage
caused by battery exposure to extreme heat, store the device out of direct sunlight.
Before you use your device on battery power, you should charge it.
1Press the suction cup to the windshield, and flip the lever back toward the windshield.
2Plug the vehicle power cable into the USB port on the device.
Getting Started 3

3Plug the other end of the vehicle power cable into a power outlet in your vehicle.
4Fit the tab on the bottom of the mount into the slot on the back of the device, and press the device into
the mount until it clicks.
4 Getting Started

Getting Started 5

Turning the Device On or Off
• To turn the device on, press the power button , or connect the device to power.
• To put the device in power saving mode, press the power button while the device is on.
While in power saving mode, the screen is off and the device uses very little power, but it can wake instantly
for use.
TIP: You can charge your device faster by putting it in power saving mode while charging the battery.
• To turn off the device completely, hold the power button until a prompt appears on the screen, and select Off.
The prompt appears after five seconds. If you release the power button before the prompt appears, the
device enters power saving mode.
Acquiring GPS Signals
When you turn on your navigation device, the GPS receiver must collect satellite data and establish the current
location. The time required to acquire satellite signals varies based on several factors, including how far you are
from the location where you last used your navigation device, whether you have a clear view of the sky, and how
long it has been since you last used your navigation device. The first time you turn on your navigation device, it
may take several minutes to acquire satellite signals.
1Turn on the device.
2Wait while the device locates satellites.
3If necessary, go to an open area, away from tall buildings and trees.
in the status bar indicates the satellite signal strength. When at least half the bars are filled, the device is
ready for navigation.
6 Getting Started

Status Bar Icons
The status bar is located at the top of the main menu. The status bar icons display information about features
on the device. You can select some icons to change settings or view additional information.
GPS signal status. Hold to view GPS accuracy and acquired satellite information (Viewing GPS
Signal Status, page 69).
Bluetooth® technology status. Select to view the Bluetooth settings (Wireless Network Settings,
page 59).
Wi-fi signal strength. Select to change the wi-fi settings (Wireless Network Settings, page 59).
Connected to hands-free calling. Select to place a phone call (Hands-Free Calling, page 39).
Active vehicle profile. Select to view the vehicle profile settings (Editing a Vehicle Profile, page 9).
Garmin eLog™ status. Select to view the current ELD information. When the icon is blue, the device
is connected to the Garmin eLog app.
Current time. Select to set the time (Setting the Time, page 61).
Battery charge level.
dēzl™ app connection status(Pairing with Your Smartphone, page 36).
Temperature. Select to view the weather forecast (Viewing the Weather Forecast, page 46).
Dash cam recording status. Select to open the dash cam controls.
Using the On-Screen Buttons
On-screen buttons allow you to navigate the pages, menus, and menu options on your device.
• Select to return to the previous menu screen.
• Hold to quickly return to the main menu.
• Select or to scroll through lists or menus.
• Hold or to scroll faster.
• Select to see a context-based menu of options for the current screen.
Adjusting the Volume
1Select .
2Select an option:
• Use the slider bar to adjust the volume.
• Select to mute the device.
• Select a check box to enable or disable additional sound options.
Getting Started 7

Using the Audio Mixer
You can use the audio mixer to set the volume levels for different audio types, such as navigation prompts or
phone calls. The level for each audio type is a percentage of the master volume.
1Select .
2Select Mixer.
3Use the sliders to adjust the volume for each audio type.
Enabling or Disabling Sounds and Audio Sources
You can turn specific audio sources and system sounds on or off without affecting other audio sources.
1Select .
2In the Sounds section, select an option:
• To enable the device to speak navigation prompts and directions, select the Spoken Navigation check
box.
• To enable the device to speak traffic alerts and prompts, select the Spoken Traffic Alerts check box.
• To enable the device to play a tone when a driver awareness alert is triggered, select the Alerts and Tones
check box.
• To enable the device to play a sound when you touch on-screen buttons, select the Button Presses check
box.
Adjusting the Screen Brightness
1Select > Display > Brightness.
2Use the slider bar to adjust the brightness.
Vehicle Profiles
WARNING
Entering your vehicle profile characteristics does not guarantee that your vehicle's characteristics will be
accounted for in all route suggestions or that you will receive the warning icons in all cases. Limitations may
exist in the map data such that your device cannot account for these restrictions or road conditions in all cases.
Always defer to all posted road signs and road conditions when making driving decisions.
Routing and navigation are calculated differently based on your vehicle profile. The activated vehicle profile is
indicated by an icon in the status bar. The navigation and map settings on your device can be customized
separately for each vehicle type.
When you activate a truck vehicle profile, the device avoids including restricted or impassable areas in routes
based on the dimensions, weight, and other characteristics you entered for your vehicle.
Adding a Vehicle Profile
You can add a vehicle profile that includes the weight, dimensions, and other characteristics for your vehicle.
1Select > Vehicle Profile > .
2Select an option:
• To add a straight truck with a permanently attached cargo area, select Straight Truck.
• To add a tractor or a tractor-trailer combination, select Tractor.
• To add a bus, select Bus.
3Follow the on-screen instructions to enter the vehicle characteristics.
After you add a vehicle profile, you can edit the profile to enter additional detailed information, such as the
vehicle identification number or trailer number (Editing a Vehicle Profile, page 9).
8 Vehicle Profiles

Adding an Environmental Zone Vehicle Profile
You can add a vehicle profile for the environmental zone settings specific to your vehicle, such as fuel type and
emission standard.
NOTE: This feature is not available for all regions or product models.
1Select > Navigation > Environmental Zones.
2Follow the on-screen instructions.
Car Profile
The car profile is a preloaded vehicle profile intended for use in an automobile without a trailer. While using the
car profile, the device calculates standard automobile routes, and routing for large vehicles is not available.
Some features and settings specific to large vehicles are not available while using the car profile.
Switching the Vehicle Profile
Each time you turn on your device, it prompts you to select a vehicle profile. You can manually switch another
vehicle profile at any time.
1From the status bar, select the vehicle profile icon, such as or .
2Select a vehicle profile.
The vehicle profile information appears, including measurements and weight.
3Select Select.
Changing Your Trailer Information
Before you can change your trailer information, you must enter a vehicle profile for a tractor (Adding a Vehicle
Profile, page 8).
When you change the trailer on your tractor, you can change the trailer information in your vehicle profile
without changing the tractor information. You can switch quickly between frequently used trailers.
1From the home screen, select the vehicle profile widget.
2Select the tractor vehicle profile to use with the trailer.
3Select .
4Select an option:
• To use a recent trailer configuration, select a trailer configuration from the list.
• To enter a new trailer configuration, select New Configuration, and enter the trailer information.
Editing a Vehicle Profile
You can edit a vehicle profile to change vehicle information or to add detailed information to a new vehicle
profile, such as the vehicle identification number, trailer number, or odometer reading. You can also rename or
delete a vehicle profile.
1Select > Vehicle Profile.
2Select the vehicle profile to edit.
3Select an option:
• To edit the vehicle profile information, select , and select a field to edit.
• To rename a vehicle profile, select > > Rename Profile.
• To delete the vehicle profile, select > > Delete.
Vehicle Profiles 9

Dash Cam
Aligning the Camera
WARNING
Do not attempt to align the camera while driving because doing so can cause distraction that could lead to an
accident resulting in serious personal injury or death.
Advanced driver assistance features may not perform properly if the camera is not aligned. You should align the
dash camera each time you mount or reposition the device.
1Select > Dash Cam > Camera Placement.
2Select Horizontal Placement, and select the horizontal location of your device on the windshield.
3Select Vehicle Height, and select your vehicle type.
4Select Alignment.
5Tilt the device and turn the camera left or right to align the camera.
The crosshairs should point straight ahead, and the horizon line should be centered between the top and
bottom of the screen.
Dash Cam Recording
NOTICE
Some jurisdictions may prohibit or regulate recording audio and video, or taking photographs. Jurisdictions may
require that all parties have knowledge of the recording and provide consent before you record audio and video
or take photographs. It is your responsibility to know and comply with all laws, regulations, and any other
restrictions in your jurisdiction.
The dash cam records video to the camera memory card. By default, the device immediately starts recording
video when it turns on, and it continues recording until it is turned off. If the memory card is full, the device
automatically deletes the oldest unsaved video to create space for new video.
When the option to promptly delete unsaved video is enabled, the device continually deletes unsaved video
more than three minutes old and deletes all unsaved video each time it is powered off. You can enable or
disable this feature in the camera settings (Dash Cam Settings, page 60).
You can save a video recording to prevent it from being overwritten or deleted.
Saving a Dash Cam Recording
You can save a portion of the recorded video to prevent it from being overwritten by new video. By default, the
device uses a sensor to detect possible accidental collisions and saves video footage before, during, and after
the detected event. You can also manually save video at any time.
1While the dash cam is recording, select Dash Cam > .
The device saves the video footage before, during, and after you select .
2Select again to extend the saved recording time (optional).
A message indicates the video is saving.
Stopping or Starting Dash Camera Recording
1Select Dash Cam.
2Select an option:
• To stop recording, select .
TIP: By default, recording starts automatically the next time you turn on the device. You can disable this
option in the camera settings (Dash Cam Settings, page 60).
• To start recording, select .
10 Dash Cam

Turning Audio Recording On or Off
NOTICE
Some jurisdictions may prohibit recording audio in the vehicle or may require that all passengers have
knowledge of the recording and provide consent before you record audio in the vehicle. It is your responsibility
to know and follow all laws and restrictions for your jurisdiction.
The device can record audio using the integrated microphone while recording video. You can turn audio
recording on or off at any time.
Select > Dash Cam > Record Audio.
Viewing Videos and Photos
NOTE: The device stops recording video while you view videos or photos.
1Select Gallery > Yes.
2Select a video or photo.
The device displays the video or photo. Videos start playing automatically. If the video or photo includes
location information, a map shows the location.
Videos on Your Computer
Media is stored in the DCIM folder on the camera memory card. Videos are stored in MP4 file format.Photos are
stored in JPG format. You can view and transfer media by connecting the memory card or the device to your
computer (Connecting the Device to Your Computer, page 67).
The media is sorted into several folders.
100EVENT: Contains videos saved automatically when the device detected an incident.
101PHOTO: Contains photos.
102SAVED: Contains videos saved manually by the user.
105UNSVD: Contains unsaved video footage. The device overwrites the oldest unsaved video when the storage
space for unsaved video is full.
Deleting a Video or Photo
1Select Gallery > Yes.
2Select a video or photo.
3Select > Yes.
Vault Storage
NOTE: This feature is not available for all countries.
You can upload, manage, and share dash camera footage on a secure, online storage drive using the Vault. The
dash camera uploads saved videos to the Vault automatically while it is connected to a Wi‑Fi® network.
You can store videos in the Vault for up to 24 hours with your dēzl account. There is no size limit to the amount
of data you can store. You can purchase an optional Vault subscription from the dēzl app on your smartphone
to extend your storage time.
NOTE: Your dash camera must be connected to a Wi‑Fi network to use this feature.
Upgrading Your Vault Subscription
You can purchase an optional Vault subscription to extend your storage time.
1From the dēzl app on your smartphone, select > Vault Access > Need More Time?.
2Follow the on-screen instructions.
Dash Cam 11

Sharing a Video
You can share a secure link to a dash camera video from the Vault.
1From the dēzl app on your smartphone, select Vault.
2Select a video, and select Secure Share.
3Follow the on-screen instructions.
Editing and Exporting a Video
You can trim the length of your video to remove unnecessary footage before exporting it to the Vault.
1While viewing a video, drag the trimming handles on the video progress bar left or right to trim the video
length.
2Select the Include Audio check box to include the recorded audio (optional).
3Select or select Export.
NOTE: You must keep the app in the foreground while exporting a video.
The app exports the trimmed video to the Vault and saves the video to your smartphone.
4After the video export is complete, select an option (optional):
• To remove the video from the camera memory card, select Remove From Camera.
• To return to the gallery, select or select Done.
Disabling a Shared Video Link
You can disable a link to a video that you previously shared from the Vault. When you disable a shared video
link, the video is set to private and the shared link and passcode are disabled.
1From the dēzl app on your smartphone, select Vault.
2Select a video, and select Disable Link > Continue.
Removing a Video from the Vault
1From the dēzl app on your smartphone, select Vault.
2Select a video, and select Remove From Vault > Continue.
12 Dash Cam

Driver Awareness Features and Alerts
CAUTION
The driver alerts and speed limit features are for information only and do not replace your responsibility to abide
by all posted speed limit signs and to use safe driving judgment at all times. Garmin® is not responsible for any
traffic fines or citations you receive for failing to follow all applicable traffic laws and signs.
Your device provides features that can help encourage safer driving and increase efficiency, even when you are
driving in a familiar area. The device plays an audible tone or message and displays information for each alert.
You can enable or disable the audible tone for some types of driver alerts. Not all alerts are available in all areas.
Schools: The device plays a tone and displays the speed limit (if available) for an upcoming school or school
zone.
Speed limit exceeded: The device displays a red border on the speed limit icon when you exceed the posted
speed limit for the current road.
Speed limit reduced: The device plays a tone and displays the upcoming speed limit so you can be prepared to
adjust your speed.
Wrong way on a one-way street: The device plays a message and displays a full-screen warning if you travel the
wrong way on a one-way street. The edges of the screen appear red and an alert remains at the top of the
screen until you leave the one-way street or correct your direction of travel.
Railroad crossing: The device displays the distance to an upcoming railroad crossing.
Animal crossing: The device plays a tone to indicate an upcoming animal crossing area.
Curves: The device plays a tone to indicate a bend in the road.
Slower traffic: The device plays a tone to indicate slower traffic when you approach slower traffic at a higher
speed. Your device must be receiving traffic information to use this feature (Traffic, page 41).
Construction zone: The device plays a tone and displays a message when you approach a construction zone.
Lane closure: The device plays a tone and displays a message when you approach a lane closure.
Break planning: The device plays a tone and suggests upcoming rest stops after you have been driving for a
long time.
No trucks allowed: The device plays a tone when you approach a road where no trucks are allowed.
Risk of grounding: The device plays a tone and displays a message when you approach a road where your
vehicle could become grounded.
Lateral wind: The device plays a tone and displays a message when you approach a road where there is risk of
lateral wind.
Narrow road: The device plays a tone and displays a message when you approach a road that may be too
narrow for your vehicle.
Steep hill: The device plays a tone and displays a message when you approach a steep hill.
State and country borders: The device plays a tone and displays a message when you approach the border of a
state or country.
Forward collision warning: The device alerts you when it detects that there is not a safe distance between your
vehicle and the vehicle in front of you.
Lane departure warning: The device alerts you when it detects you may be crossing a lane boundary
unintentionally.
Enabling or Disabling Driver Alerts
You can enable or disable several types of driver alerts.
1Select > Driver Assistance > Driver Alerts.
2Select or clear the check box next to each alert.
Driver Awareness Features and Alerts 13

Red Light and Speed Cameras
NOTICE
Garmin is not responsible for the accuracy of or the consequences of using a red light or speed camera
database.
NOTE: This feature is not available for all regions or product models.
Information about red light and speed camera locations is available in some areas for some product models.
The device alerts you when you approach a reported speed or red light camera.
• In some areas, your device can receive red light and speed camera data while connected to a smartphone
running the dēzl app.
• You can use the Garmin Express™ software (garmin.com/express) to update the camera database stored on
your device. You should update your device frequently to receive the most up-to-date camera information.
Advanced Driver Assistance System
Your device includes an advanced driver assistance system (ADAS), which uses the integrated dash camera to
provide warnings and alerts about your driving environment.
You can enable or disable each of the advanced driver assistance features in the Driver Assistance settings
(Driver Assistance Settings, page 59).
Forward Collision Warning System
WARNING
The forward collision warning system (FCWS) feature is for information only and does not replace your
responsibility to observe all road and driving conditions, abide by all traffic regulations, and use safe driving
judgment at all times. The FCWS relies on the camera to provide a warning of upcoming vehicles and, as a
result, may have limited functionality in low visibility conditions. For more information, go to garmin.com
/warnings.
The FCWS feature alerts you when the device detects that there is not a safe distance between your vehicle and
the vehicle in front of you. The device determines your vehicle speed using GPS, and it calculates an estimated
safe following distance based on your speed. The FCWS activates automatically when your vehicle speed
exceeds 65 km/hr (40 mph).
When the device detects that you are too close to the vehicle in front of you, the device plays an audible alert,
and a warning appears on the screen.
Forward Collision Warning System Performance Tips
Several factors affect the performance of the forward collision warning system (FCWS). Some conditions may
prevent the FCWS feature from detecting a vehicle in front of you.
• The FCWS feature activates only when your vehicle speed exceeds 65 km/h (40 mph).
• The FCWS feature may not detect a vehicle in front of you when the camera's view of the vehicle is obscured
by rain, fog, snow, sun or headlight glare, or darkness.
• The FCWS feature may not function properly if the camera is incorrectly aligned .
• The FCWS feature may not detect vehicles farther away than 40 m (130 ft.) or closer than 5 m (16 ft.).
• The FCWS feature may not function properly if the camera placement settings do not correctly indicate your
vehicle height or the placement of your device in the vehicle .
14 Driver Awareness Features and Alerts