Garmin Gpsmap 87 series User manual

GPSMAP®84XX/86XX/87XX

Owner’s Manual

products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin.com for current updates

and supplemental information concerning the use of this product.

Garmin®, the Garmin logo, ActiveCaptain®, ANT®, BlueChart®, Fusion®, GPSMAP®, inReach®, Ultrascroll®, and VIRB® are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and

other countries. ActiveCaptain®, Apollo™, Connect IQ™, ECHOMAP™, Fantom™, Fusion-Link™, Fusion PartyBus™, Garmin ClearVü™, Garmin Connect™, Garmin Express™, Garmin Nautix™,

Garmin Quickdraw™, GC™, GCV™, GMM™, GMR™, GRID™, GXM™, LiveScope™, MotionScope™, OneChart™, OneHelm™, Panoptix™, Reactor™, Shadow Drive™, SmartMode™, and SteadyCast™

are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.

Apple® and Mac® are trademarks of Apple Inc., registered in the U.S. and other countries. Android™ is a trademark of Google™ Inc. The BLUETOOTH® word mark and logos are owned by the

Bluetooth SIG, Inc. and any use of such marks by Garmin is under license. Blu-Ray™ is a registered trademark of the Blu-ray Disc Association. Chromecast™ is a registered trademark of Google

Inc. CZone™ is a trademark of Power Products, LLC. Color Thermal Vision™ is a trademark of FLIR Systems, Inc. FLIR® and MSX® are registered trademarks of FLIR Systems, Inc. HDMI® is a

registered trademark of HDMI Licensing, LLC. NMEA®, NMEA 2000®, and the NMEA 2000 logo are registered trademarks of the National Marine Electronics Association. microSD® and the

microSD logo are trademarks of SD-3C, LLC. Optimus®, SeaWays®, and SeaStation® are registered trademarks of Dometic®. SD® and the SDHC logo are trademarks of SD-3C, LLC. SiriusXM®

Microsoft Corporation in the United States and other countries. Yamaha®, the Yamaha logo, Command Link Plus®, and Helm Master® are trademarks of the YAMAHA Motor Co., LTD. All other

trademarks and copyrights are the property of their respective owners.

Table of Contents

Introduction.....................................................................1

Protective Cover......................................................................... 1

Device Overview......................................................................... 1

Using the Touchscreen.......................................................... 1

On-Screen Buttons................................................................ 1

Locking and Unlocking the Touchscreen............................... 1

Connector View (8x10, 8x12, and 8x16 models)................... 1

Connector View (8x17, 8x22, and 8x24 models)................... 2

Connector View (8700 models)..............................................2

Tips and Shortcuts (MFD models).............................................. 2

Tips and Shortcuts (8700 model)................................................2

Accessing Owner's Manuals on the Chartplotter........................ 2

Downloading the Manuals from the Web.................................... 3

Garmin Support Center...............................................................3

Memory Cards............................................................................ 3

Inserting Memory Cards (GPSMAP 8x10/8x12/8x16)........... 3

Inserting a Memory Card (GPSMAP

8x17/8x22/8x24/87xx)............................................................ 3

Acquiring GPS Satellite Signals..................................................3

Selecting the GPS Source..................................................... 3

Customizing the Chartplotter........................................ 3

Home Screen.............................................................................. 3

Adding an Item to Favorites................................................... 4

Customizing the Home Screen.............................................. 4

Customizing Pages..................................................................... 4

Customizing the Layout of a SmartMode or Combination

Page.......................................................................................4

Changing the Background Image.......................................... 4

Customizing the Startup Screen............................................ 4

Recommended Startup Image Dimensions...................... 4

Adding a SmartMode Layout................................................. 4

Creating a New Combination Page....................................... 5

Deleting a Combination Page................................................ 5

Customizing the Data Overlays............................................. 5

Resetting the Station Layouts................................................ 5

Presets........................................................................................5

Saving a New Preset............................................................. 5

Managing Presets.................................................................. 5

Setting the Vessel Type.............................................................. 5

Adjusting the Backlight............................................................... 5

Adjusting the Color Mode........................................................... 6

Turning On the Chartplotter Automatically................................. 6

Enabling Screen Lock................................................................. 6

Automatically Turning Off the System........................................ 6

ActiveCaptain App......................................................... 6

ActiveCaptain Roles................................................................... 6

Getting Started with the ActiveCaptain App............................... 6

Enabling Smart Notifications.......................................................6

Receiving Notifications...........................................................7

Managing Notifications...........................................................7

Making Notifications Private...................................................7

Updating Software with the ActiveCaptain App.......................... 7

Updating Charts with ActiveCaptain........................................... 7

Communication with Wireless Devices........................ 8

Wi‑Fi Network............................................................................. 8

Setting Up the Wi‑Fi Wireless Network.................................. 8

Connecting a Wireless Device to the Chartplotter................. 8

Changing the Wireless Channel............................................ 8

Changing the Wi‑Fi Host........................................................ 8

Wireless Remote Control............................................................ 8

Pairing the Wireless Remote Control With the

Chartplotter............................................................................ 8

Turning On and Off the Remote Backlight............................. 8

Disconnecting the Remote from All Chartplotters.................. 8

Wireless Wind Sensor................................................................ 8

Connecting a Wireless Sensor to the Chartplotter................. 8

Adjusting the Wind Sensor Orientation.................................. 8

Viewing Boat Data on a Garmin Watch...................................... 8

Viewing Boat Data on a Garmin Nautix™ Device...................... 9

Charts and 3D Chart Views........................................... 9

Navigation Chart and Fishing Chart........................................... 9

Zooming In and Out Using the Touchscreen......................... 9

Chart Symbols....................................................................... 9

Measuring a Distance on the Chart....................................... 9

Creating a Waypoint on the Chart....................................... 10

Viewing Location and Object Information on a Chart.......... 10

Viewing Details about Navaids............................................ 10

Navigating to a Point on the Chart....................................... 10

Premium Charts........................................................................ 10

Fish Eye 3D Chart View....................................................... 10

Viewing Tide Station Information......................................... 10

Animated Tide and Current Indicators............................ 11

Showing Tides and Current Indicators............................ 11

Showing Satellite Imagery on the Navigation Chart............ 11

Viewing Aerial Photos of Landmarks................................... 11

Automatic Identification System................................................11

AIS Targeting Symbols........................................................ 11

Heading and Projected Course of Activated AIS Targets.... 12

Activating a Target for an AIS Vessel.................................. 12

Viewing Information about a Targeted AIS Vessel......... 12

Deactivating a Target for an AIS Vessel......................... 12

Viewing a List of AIS and MARPA Threats.......................... 12

Setting the Safe-Zone Collision Alarm................................. 12

AIS Aids to Navigation......................................................... 12

AIS Distress Signals............................................................ 13

Navigating to a Distress Signal Transmission................. 13

AIS Distress Signal Device Targeting Symbols.............. 13

Enabling AIS Transmission Test Alerts........................... 13

Turning Off AIS Reception................................................... 13

Chart Menu............................................................................... 13

Chart Layers........................................................................ 13

Chart Layer Settings....................................................... 13

Depth Layer Settings.......................................................13

My Vessel Layer Settings................................................14

Laylines Settings............................................................. 14

User Data Layer Settings................................................ 14

Other Vessels Layer Settings..........................................14

Water Layer Settings.......................................................14

Depth Range Shading..................................................... 14

Weather Layer Settings...................................................15

Radar Overlay Settings................................................... 15

Chart Settings...................................................................... 15

Fish Eye 3D Settings........................................................... 15

Supported Maps....................................................................... 15

Garmin Quickdraw Contours Mapping....................... 15

Mapping a Body of Water Using the Garmin Quickdraw

Contours Feature...................................................................... 16

Adding a Label to a Garmin Quickdraw Contours Map............ 16

Garmin Quickdraw Community................................................. 16

Connecting to the Garmin Quickdraw Community with

ActiveCaptain....................................................................... 16

Downloading Garmin Quickdraw Community Maps Using

ActiveCaptain.................................................................. 16

Sharing Your Garmin Quickdraw Contours Maps with the

Garmin Quickdraw Community Using ActiveCaptain...... 16

Connecting to the Garmin Quickdraw Community with

Garmin Connect................................................................... 16

Sharing Your Garmin Quickdraw Contours Maps with the

Garmin Quickdraw Community Using Garmin Connect.. 16

Table of Contents i

Downloading Garmin Quickdraw Community Maps Using

Garmin Connect.............................................................. 16

Garmin Quickdraw Contours Settings...................................... 17

Navigation with a Chartplotter.................................... 17

Basic Navigation Questions...................................................... 17

Destinations.............................................................................. 17

Searching for a Destination by Name.................................. 18

Selecting a Destination Using the Navigation Chart............ 18

Searching for a Marine Services Destination....................... 18

Setting and Following a Direct Course Using Go To........... 18

Stopping Navigation............................................................. 18

Waypoints................................................................................. 18

Marking Your Present Location as a Waypoint.................... 18

Creating a Waypoint at a Different Location........................ 18

Marking an SOS Location.................................................... 18

Projecting a Waypoint.......................................................... 18

Viewing a List of all Waypoints............................................ 18

Editing a Saved Waypoint.................................................... 18

Moving a Saved Waypoint................................................... 18

Browsing for and Navigating to a Saved Waypoint.............. 19

Deleting a Waypoint or an MOB.......................................... 19

Deleting All Waypoints......................................................... 19

Routes...................................................................................... 19

Creating and Navigating a Route From Your Present

Location............................................................................... 19

Creating and Saving a Route............................................... 19

Viewing a List of Routes and Auto Guidance Paths............ 19

Editing a Saved Route......................................................... 19

Browsing for and Navigating a Saved Route....................... 19

Browsing for and Navigating Parallel to a Saved Route...... 20

Initiating a Search Pattern....................................................20

Deleting a Saved Route....................................................... 20

Deleting All Saved Routes................................................... 20

Auto Guidance.......................................................................... 20

Setting and Following an Auto Guidance Path.................... 20

Creating and Saving an Auto Guidance Path...................... 20

Adjusting a Saved Auto Guidance Path............................... 20

Canceling an Auto Guidance Calculation in Progress......... 21

Setting a Timed Arrival.........................................................21

Auto Guidance Path Configurations.................................... 21

Adjusting the Distance from Shore..................................21

Tracks....................................................................................... 21

Showing Tracks................................................................... 21

Setting the Color of the Active Track................................... 21

Saving the Active Track....................................................... 22

Viewing a List of Saved Tracks............................................ 22

Editing a Saved Track.......................................................... 22

Saving a Track as a Route...................................................22

Browsing for and Navigating a Recorded Track.................. 22

Deleting a Saved Track........................................................22

Deleting All Saved Tracks.................................................... 22

Retracing the Active Track................................................... 22

Clearing the Active Track..................................................... 22

Managing the Track Log Memory During Recording........... 22

Configuring the Recording Interval of the Track Log........... 22

Boundaries................................................................................22

Creating a Boundary............................................................ 22

Converting a Route to a Boundary...................................... 22

Converting a Track to a Boundary....................................... 22

Editing a Boundary...............................................................22

Linking a Boundary to a SmartMode Layout........................ 23

Setting a Boundary Alarm.................................................... 23

Disabling all Boundary Alarms............................................. 23

Deleting a Boundary............................................................ 23

Deleting All Saved Waypoints, Tracks, Routes, and

Boundaries................................................................................23

Sailing Features............................................................ 23

Setting the Vessel Type for Sailing Features........................... 23

Sail Racing................................................................................23

Starting Line Guidance........................................................ 23

Setting the Starting Line.................................................. 23

Using the Starting Line Guidance................................... 23

Starting the Race Timer....................................................... 23

Stopping the Race Timer..................................................... 23

Setting the Distance between the Bow and the GPS

Antenna................................................................................24

Laylines Settings.......................................................................24

Setting the Keel Offset.............................................................. 24

Sailboat Autopilot Operation..................................................... 24

Wind Hold............................................................................ 24

Setting the Wind Hold Type............................................ 24

Engaging Wind Hold....................................................... 24

Engaging Wind Hold from Heading Hold........................ 25

Adjusting the Wind Hold Angle with the Autopilot........... 25

Tack and Gybe.....................................................................25

Tacking and Gybing from Heading Hold......................... 25

Tacking and Gybing from Wind Hold.............................. 25

Setting a Tack and Gybe Delay...................................... 25

Enabling the Gybe Inhibitor............................................. 25

Heading Line and Angle Markers............................................. 25

Setting the Heading Line and Angle Markers...................... 25

Sonar Fishfinder........................................................... 25

Stopping the Transmission of Sonar Signals............................ 25

Changing the Sonar View......................................................... 25

Traditional Sonar View..............................................................25

Split-Frequency Sonar View................................................ 26

Split-Zoom Sonar View........................................................ 26

Garmin ClearVü Sonar View.....................................................26

Garmin SideVü™ Sonar View.................................................. 26

SideVü Scanning Technology.............................................. 26

Measuring Distance on the Sonar Screen........................... 26

Panoptix Sonar Views...............................................................26

LiveVü Down Sonar View.................................................... 27

LiveVü Forward Sonar View................................................ 27

RealVü 3D Forward Sonar View.......................................... 27

RealVü 3D Down Sonar View.............................................. 27

RealVü 3D Historical Sonar View........................................ 27

FrontVü Sonar View............................................................. 28

Panoptix LiveScope Sonar View.......................................... 28

Perspective View................................................................. 28

Selecting the Transducer Type................................................. 28

Selecting a Sonar Source......................................................... 28

Renaming a Sonar Source...................................................28

Creating a Waypoint on the Sonar Screen............................... 28

Pausing the Sonar Display....................................................... 28

Viewing Sonar History.............................................................. 28

Sonar Sharing........................................................................... 28

Adjusting the Level of Detail..................................................... 29

Adjusting the Color Intensity..................................................... 29

Sonar Recordings..................................................................... 29

Recording the Sonar Display............................................... 29

Stopping the Sonar Recording............................................. 29

Deleting a Sonar Recording................................................. 29

Playing Sonar Recordings................................................... 29

Traditional, Garmin ClearVü, and SideVü Sonar Setup........... 29

Setting the Zoom Level on the Sonar Screen...................... 29

Setting the Scroll Speed...................................................... 30

Adjusting the Range of the Depth or Width Scale............... 30

Sonar Noise Rejection Settings........................................... 30

Sonar Appearance Settings................................................. 30

Sonar Alarms....................................................................... 31

Advanced Sonar Settings.................................................... 31

ii Table of Contents

Traditional, Garmin ClearVü, and SideVü Transducer

Installation Settings.............................................................. 31

Sonar Frequencies...............................................................31

Selecting the Transducer Frequency.............................. 32

Creating a Frequency Preset.......................................... 32

Turning On the A-Scope...................................................... 32

Panoptix Sonar Setup............................................................... 32

Zooming in a Panoptix LiveVü or LiveScope Sonar View.... 32

Adjusting the RealVü Viewing Angle and Zoom Level......... 32

Adjusting the RealVü Sweep Speed.................................... 32

LiveVü Forward and FrontVü Sonar Menu.......................... 32

Setting the LiveVü and FrontVü Transducer Transmit

Angle............................................................................... 33

Setting the FrontVü Depth Alarm.................................... 33

LiveVü and FrontVü Appearance Settings...................... 33

LiveVü and FrontVü Layout Settings.............................. 33

RealVü Appearance Settings............................................... 33

LiveScope and Perspective Sonar Menu............................. 33

LiveScope and Perspective Sonar Setup....................... 34

LiveScope and Perspective Appearance Settings.......... 34

LiveScope and Perspective Layout Settings................... 34

Panoptix Transducer Installation Settings........................... 34

Setting the Bow Offset.................................................... 35

Calibrating the Compass................................................. 35

Radar............................................................................. 35

Radar Interpretation.................................................................. 35

Radar Overlay...................................................................... 35

Radar Overlay and Chart Data Alignment........................... 35

Transmitting Radar Signals...................................................... 36

Stopping the Transmission of Radar Signals....................... 36

Setting Up the Timed Transmit Mode.................................. 36

Enabling and Adjusting a Radar No Transmit Zone............ 36

Adjusting the Radar Range...................................................... 36

Tips for Selecting a Radar Range........................................ 36

MotionScope™ Doppler Radar Technology............................. 36

Enabling a Guard Zone............................................................ 36

Defining a Circular Guard Zone........................................... 36

Defining a Partial Guard Zone............................................. 37

MARPA..................................................................................... 37

MARPA Targeting Symbols................................................. 37

Acquiring MARPA Targets Automatically.............................37

Assigning a MARPA Tag to an Object................................. 37

Removing a MARPA Tag from a Targeted Object............... 37

Viewing Information about a MARPA-tagged Object........... 37

Viewing a List of AIS and MARPA Threats.......................... 37

Showing AIS Vessels on the Radar Screen........................ 37

VRM and EBL...................................................................... 37

Showing and Adjusting the VRM and the EBL................ 38

Measuring the Range and Bearing to a Target Object... 38

Echo Trails................................................................................ 38

Turning on Echo Trails......................................................... 38

Adjusting the Length of the Echo Trails............................... 38

Clearing the Echo Trails.......................................................38

Radar Settings.......................................................................... 38

Radar Gain...........................................................................38

Adjusting Gain on the Radar Screen Automatically........ 38

Adjusting Gain on the Radar Screen Manually............... 38

Minimizing Nearby Large-Object Interference.................38

Minimizing Side-Lobe Interference on the Radar

Screen............................................................................. 38

Radar Filter Settings............................................................ 39

Adjusting Sea Clutter on the Radar Screen.................... 39

Adjusting Rain Clutter on the Radar Screen................... 39

Averaging Multiple Scans on the Radar Screen............. 39

Radar Options Menu............................................................ 39

Radar Setup Menu............................................................... 39

Reducing Cross Talk Clutter on the Radar Screen......... 39

Radar Appearance Settings................................................. 39

Radar Installation Settings................................................... 40

Front-of-Boat Offset........................................................ 40

Setting a Custom Park Position...................................... 40

Radar My Vessel Layer Settings..........................................40

Selecting a Different Radar Source.......................................... 40

Changing the Radar Mode....................................................... 40

Autopilot........................................................................ 40

Autopilot Configuration............................................................. 40

Selecting the Preferred Heading Source............................. 40

Opening the Autopilot Screen................................................... 41

Autopilot Screen....................................................................... 41

Adjusting the Step Steering Increment................................ 41

Setting the Power Saver...................................................... 41

Enabling Shadow Drive™.................................................... 41

Autopilot Overlay Bar................................................................ 41

Engaging the Autopilot............................................................. 41

Adjusting the Heading with the Helm................................... 41

Adjusting the Heading with the Chartplotter in Step Steering

Mode.................................................................................... 41

Steering Patterns...................................................................... 41

Following the U-Turn Pattern............................................... 41

Setting Up and Following the Circles Pattern...................... 41

Setting Up and Following the Zigzag Pattern...................... 41

Following the Williamson Turn Pattern................................ 42

Following an Orbit Pattern................................................... 42

Setting Up and Following the Cloverleaf Pattern................. 42

Setting Up and Following a Search Pattern......................... 42

Cancelling a Steering Pattern.............................................. 42

Adjusting the Autopilot Response............................................. 42

Enabling the Autopilot Controls on a Garmin Watch................ 42

Customizing the Autopilot Button Actions............................ 42

Controlling the Autopilot with a GRID 20 Remote Control........ 42

Reactor™ Autopilot Remote Control........................................ 42

Pairing a Reactor Autopilot Remote Control With a

Chartplotter.......................................................................... 42

Changing the Functions of the Reactor Autopilot Remote

Control Action Keys............................................................. 42

Updating the Reactor Autopilot Remote Control Software.. 43

Yamaha Autopilot..................................................................... 43

Yamaha Autopilot Screen.................................................... 43

Yamaha Autopilot Settings.............................................. 43

Yamaha Autopilot Overlay Bar.............................................43

Force® Trolling Motor Control.................................... 43

Connecting to a Trolling Motor..................................................44

Adding the Trolling Motor Controls to Screens......................... 44

Trolling Motor Control Bar.................................................... 44

Trolling Motor Settings.............................................................. 44

Assigning a Shortcut to the Trolling Motor Remote Control

Shortcut Keys.......................................................................44

Calibrating the Trolling Motor Compass...............................44

Setting the Bow Offset......................................................... 44

Digital Selective Calling............................................... 45

Networked Chartplotter and VHF Radio Functionality.............. 45

Turning On DSC....................................................................... 45

DSC List....................................................................................45

Viewing the DSC List........................................................... 45

Adding a DSC Contact......................................................... 45

Incoming Distress Calls............................................................ 45

Navigating to a Vessel in Distress....................................... 45

Man-Overboard Distress Calls Initiated from a VHF

Radio....................................................................................45

Man-Overboard and SOS Distress Calls Initiated from the

Chartplotter.......................................................................... 45

Table of Contents iii

Position Tracking...................................................................... 45

Viewing a Position Report.................................................... 45

Navigating to a Tracked Vessel........................................... 45

Creating a Waypoint at the Position of a Tracked Vessel.... 46

Editing Information in a Position Report.............................. 46

Deleting a Position-Report Call............................................ 46

Viewing Vessel Trails on the Chart...................................... 46

Individual Routine Calls............................................................ 46

Selecting a DSC Channel.................................................... 46

Making an Individual Routine Call....................................... 46

Making an Individual Routine Call to an AIS Target............ 46

Gauges and Graphs..................................................... 46

Viewing the Gauges..................................................................46

Changing the Data Shown in a Gauge................................ 46

Customizing the Gauges......................................................46

Customizing Engine Gauge and Fuel Gauge Limits............ 46

Selecting the Number of Engines Shown in Gauges........... 47

Customizing the Engines Shown in Gauges........................ 47

Enabling Status Alarms for Engine Gauges........................ 47

Enabling Some Engine Gauge Status Alarms..................... 47

Yamaha Engine Gauges.......................................................... 47

Engine Condition Icons........................................................ 47

Engine Alert Icons................................................................ 47

Setting Up the Gauges.........................................................47

Configuring the Number of Engines................................ 47

Configuring the Tank Level Sensors............................... 47

Changing the Data Shown.............................................. 48

Yamaha Engine Data Settings........................................ 48

Setting the Fuel Alarm.............................................................. 48

Setting the Fuel Capacity of the Vessel............................... 48

Synchronizing the Fuel Data with the Actual Vessel Fuel... 48

Viewing the Wind Gauges........................................................ 48

Configuring the Sailing Wind Gauge.................................... 48

Configuring the Speed Source............................................. 48

Configuring the Heading Source of the Wind Gauge........... 48

Customizing the Close-Hauled Wind Gauge....................... 49

Viewing Trip Gauges................................................................ 49

Resetting Trip Gauges......................................................... 49

Battery Management................................................................ 49

Setting Up the Battery Management Page.......................... 49

Viewing Graphs........................................................................ 49

Setting the Graph Range and Time Scales......................... 49

inReach® Messages..................................................... 49

Connecting an inReach Device to the Chartplotter.................. 49

Receiving inReach Messages.................................................. 49

Sending an inReach Preset Message...................................... 49

Replying to an inReach Message............................................. 50

Digital Switching.......................................................... 50

Adding and Editing a Digital Switching Page............................ 50

Dometic® Optimus® Features.................................... 50

Activating the Optimus Overlay Bar.......................................... 50

Optimus Overlay Bar Overview................................................ 50

Optimus Overlay Symbols........................................................ 50

Optimus Limp Home Mode....................................................... 50

Tide, Current, and Celestial Information.................... 50

Tide Station Information............................................................50

Current Station Information.......................................................50

Celestial Information................................................................. 51

Viewing Tide Station, Current Station, or Celestial Information

for a Different Date................................................................... 51

Viewing Information for a Different Tide or Current Station...... 51

Viewing Almanac Information from the Navigation Chart......... 51

Warning Manager......................................................... 51

Viewing Messages.................................................................... 51

Sorting and Filtering Messages................................................ 51

Saving Messages to a Memory Card........................................51

Clearing all of the Messages.................................................... 51

Media Player................................................................. 51

Opening the Media Player........................................................ 51

Media Player Icons.............................................................. 51

Selecting the Media Device and Source................................... 51

Playing Music............................................................................51

Browsing for Music...............................................................51

Enabling Alphabetical Search......................................... 52

Setting a Song to Repeat..................................................... 52

Setting All Songs to Repeat................................................. 52

Setting Songs to Shuffle...................................................... 52

Joining the Fusion PartyBus™ Network.............................. 52

Adjusting the Volume................................................................ 52

Muting the Media Volume.................................................... 52

Enabling and Disabling Zones............................................. 52

VHF Radio................................................................................ 52

Scanning VHF Channels......................................................52

Adjusting the VHF Squelch.................................................. 52

Radio........................................................................................ 52

Setting the Tuner Region..................................................... 52

Changing the Radio Station................................................. 52

Changing the Tuning Mode................................................. 52

Presets................................................................................. 52

Saving a Station as a Preset........................................... 52

Selecting a Preset........................................................... 52

Removing a Preset..........................................................52

DAB Playback........................................................................... 52

Setting the DAB Tuner Region............................................ 52

Scanning for DAB Stations.................................................. 53

Changing DAB Stations....................................................... 53

Selecting a DAB Station from a List................................ 53

Selecting a DAB Station from a Category....................... 53

DAB Presets........................................................................ 53

Saving a DAB Station as a Preset.................................. 53

Selecting a DAB Preset from a List................................. 53

Removing DAB Presets.................................................. 53

SiriusXM Satellite Radio........................................................... 53

Locating a SiriusXM Radio ID.............................................. 53

Activating a SiriusXM Subscription...................................... 53

Customizing the Channel Guide.......................................... 53

Saving a SiriusXM Channel to the Presets List................... 53

Parental Controls................................................................. 53

Unlocking SiriusXM Parental Controls............................ 53

Setting Parental Controls on SiriusXM Radio

Channels......................................................................... 53

Clearing All Locked Channels on a SiriusXM Radio....... 54

Restoring Default Parental Control Settings Values....... 54

Changing a Parental Passcode on a SiriusXM Radio..... 54

Setting the Device Name.......................................................... 54

Updating the Media Player Software........................................ 54

Audio Return Channel.............................................................. 54

SiriusXM Weather......................................................... 54

SiriusXM Equipment and Subscription Requirements.............. 54

Weather Data Broadcasts.........................................................54

Weather Warnings and Weather Bulletins................................ 54

Changing the Weather Chart.................................................... 54

Viewing Precipitation Information............................................. 54

Storm Cell and Lightning Information.................................. 55

Hurricane Information.......................................................... 55

Forecast Information................................................................. 55

Viewing a Marine Forecast or an Offshore Forecast........... 55

Viewing Forecast Information for Another Time Period....... 55

Weather Fronts and Pressure Centers................................ 55

City Forecasts...................................................................... 55

iv Table of Contents

Viewing Fish Mapping Data...................................................... 55

Viewing Sea Conditions............................................................ 55

Surface Winds......................................................................55

Wave Height, Wave Period, and Wave Direction................ 55

Viewing Forecast Sea Conditions Information for Another

Time Period..........................................................................56

Viewing Sea Temperature Information..................................... 56

Surface Pressure and Water Temperature Data................. 56

Changing the Sea Surface Temperature Color Range........ 56

Visibility Information.................................................................. 56

Viewing Forecast Visibility Information for Another Time

Period...................................................................................56

Viewing Buoy Reports.............................................................. 56

Viewing Local Weather Information near a Buoy................. 56

Weather Overlay....................................................................... 56

Viewing Weather Subscription Information............................... 56

Viewing Video............................................................... 56

Selecting a Video Source......................................................... 56

Alternating Among Multiple Video Sources......................... 57

Networked Video Devices.........................................................57

Using Video Presets on Networked Video Cameras........... 57

Saving Video Presets on a Networked Video Camera... 57

Naming Video Presets on a Networked Video Camera.. 57

Activating Video Presets on a Networked Video

Camera........................................................................... 57

Camera Settings.................................................................. 57

Video Settings...................................................................... 57

Associating the Camera to a Video Source......................... 57

Video Camera Movement Control........................................57

Controlling Video Cameras Using On-Screen Controls.. 57

Controlling a Video Camera Using Gestures.................. 58

Configuring the Video Appearance........................................... 58

Garmin VIRB® Action Cameras............................................... 58

Connecting a VIRB 360 Action Camera.............................. 58

Connecting a VIRB Action Camera......................................58

Controlling the VIRB Action Camera with the Chartplotter.. 58

Controlling the VIRB Action Camera Video Playback..... 58

Deleting a VIRB Video.................................................... 59

Starting a VIRB Video Slideshow.................................... 59

VIRB Action Camera Settings......................................... 59

VIRB Action Camera Video Setup Settings.................... 59

Adding the VIRB Action Camera Controls to Other

Screens................................................................................ 59

HDMI Video Considerations..................................................... 59

Controlling HDMI Audio............................................................ 60

Pairing the GC™ 100 Camera with a Garmin Chartplotter....... 60

Device Configuration................................................... 60

System Settings........................................................................ 60

Sounds and Display Settings............................................... 60

Audio Settings................................................................. 60

GPS Settings....................................................................... 60

Station Settings.................................................................... 60

Viewing System Software Information................................. 61

Viewing the Event Log.................................................... 61

Viewing E-label Regulatory and Compliance Information.... 61

Preferences Settings................................................................ 61

Units Settings....................................................................... 61

Navigation Settings.............................................................. 61

Auto Guidance Path Configurations................................ 61

Adjusting the Distance from Shore..................................61

Communications Settings......................................................... 62

NMEA 0183 Settings............................................................62

Configuring NMEA 0183 Output Sentences................... 62

Setting the Communication Format for Each NMEA 0183

Port..................................................................................62

NMEA 2000 Settings............................................................62

Naming Devices and Sensors on the Network............... 62

Marine Network.................................................................... 62

Setting Alarms.......................................................................... 63

Navigation Alarms................................................................ 63

Setting the Anchor Drag Alarm....................................... 63

System Alarms..................................................................... 63

Sonar Alarms....................................................................... 63

Setting Weather Alarms....................................................... 63

Setting the Fuel Alarm......................................................... 63

My Vessel Settings................................................................... 63

Setting the Keel Offset......................................................... 64

Setting the Water Temperature Offset................................. 64

Calibrating a Water-Speed Device.......................................64

Other Vessels Settings............................................................. 64

Settings that are Synced on the Garmin Marine Network........ 65

Restoring the Original Chartplotter Factory Settings................ 65

Sharing and Managing User Data............................... 65

Selecting a File Type for Third-Party Waypoints and Routes... 65

Copying User Data from a Memory Card................................. 65

Copying User Data to a Memory Card......................................65

Updating Built-In Maps with a Memory Card and Garmin

Express..................................................................................... 66

Backing Up Data to a Computer............................................... 66

Restoring Backup Data to a Chartplotter.................................. 66

Saving System Information to a Memory Card......................... 66

Appendix....................................................................... 66

ActiveCaptain and Garmin Express.......................................... 66

Garmin Express App.................................................................66

Installing the Garmin Express App on a Computer.............. 66

Registering Your Device Using the Garmin Express App.... 66

Updating Your Charts Using the Garmin Express App........ 67

Software Updates................................................................ 67

Loading the New Software on a Memory Card Using

Garmin Express.............................................................. 67

Updating the Device Software Using a Memory Card.... 67

NMEA 0183 with Audio Cable Pinout....................................... 68

Touchscreen Controls for a Connected Computer (MFD

models)..................................................................................... 68

Touchscreen Controls for a Connected Computer (8700

Model)....................................................................................... 68

Controlling a Computer with the Chartplotter........................... 69

Pairing the GRID Device with the Chartplotter from the

Chartplotter............................................................................... 69

Pairing the GRID Device with the Chartplotter from the GRID

Device.................................................................................. 69

Rotating the GRID Remote Input Device............................. 69

Cleaning the Screen................................................................. 69

Viewing Images on a Memory card.......................................... 69

Screenshots.............................................................................. 69

Capturing Screenshots........................................................ 69

Copying Screenshots to a Computer................................... 69

Troubleshooting........................................................................ 69

My device will not acquire GPS signals............................... 69

My device will not turn on or keeps turning off..................... 70

My device is not creating waypoints in the correct

location.................................................................................70

Contacting Garmin Support...................................................... 70

Specifications............................................................................70

GPSMAP 8x10 Specifications..............................................70

GPSMAP 8x12 Specifications..............................................70

GPSMAP 8x16 Specifications..............................................71

GPSMAP 8x17 Specifications..............................................71

GPSMAP 8x22 Specifications..............................................71

GPSMAP 8x24 Specifications..............................................71

GPSMAP 8700 Specifications............................................. 72

Sonar Models Specifications................................................72

Table of Contents v

NMEA 2000 PGN Information.............................................. 72

J1939 Information................................................................ 73

NMEA 0183 Information.......................................................73

Index.............................................................................. 74

vi Table of Contents

Introduction

WARNING

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

All route and navigation lines displayed on the chartplotter are

only intended to provide general route guidance or to identify

proper channels, and are not intended to be precisely followed.

Always defer to the navaids and conditions on the water when

navigating to avoid groundings or hazards that could result in

vessel damage, personal injury, or death.

NOTE: Not all features are available on all models.

The Garmin® website at support.garmin.com presents up-to-date

information about your product. The support pages will provide

answers to frequently asked support questions, and you can

download software and chart updates. There is also contact

information to Garmin support should you have any questions.

Protective Cover

NOTICE

Before moving the vessel, remove the sun cover. Leaving the

sun cover in place while the boat is moving could result in the

sun cover becoming detached and possibly becoming lost or

falling into the water.

Some protective covers contain magnets. Under certain

circumstances, magnets may cause damage to some electronic

devices, including hard drives in laptop computers. Use caution

when the sun cover is near electronic devices.

The protective cover protects the screen when the device is not

in use.

To remove the cover, hold the edge, and pull forward.

Device Overview

Touchscreen

Power key

Automatic backlight sensor

Using the Touchscreen

• Tap the screen to select an item.

• Drag or swipe your finger across the screen to pan or scroll.

• Pinch two fingers together to zoom out.

• Spread two fingers apart to zoom in.

On-Screen Buttons

These on-screen buttons may be displayed on some screens

and functions. Some buttons are accessible only in a

combination page or SmartMode™ layout or when accessories,

such as a radar, are connected.

Button Function

Clears the on-screen icons and re-centers the screen on the

boat

Opens a full-screen view of the item

Creates a new waypoint

Creates a route, with turns, to the destination

Adds a turn to the route at the selected location

Removes the last added turn from the route

Creates a direct route, without turns, to the destination

Creates an Auto Guidance route to the destination

Begins navigation

Ends navigation

Stops and starts radar transmission

Opens the radar gain adjustment menu

Opens the radar sea clutter adjustment menu

Opens the radar rain clutter adjustment menu

Turns on and off the radar echo trails

Acquires a radar target and begins tracking it

Shows and sets the VRM/EBL line

Opens the menu for the page or function

Opens the Weather menu for the page or function

Opens the Radar menu for the page or function

Opens the Presets menu for the page or function

Locking and Unlocking the Touchscreen

You can lock the touchscreen to prevent inadvertent screen

touches.

1Select > Lock Touchscreen to lock the screen.

2Select to unlock the screen.

Connector View (8x10, 8x12, and 8x16 models)

The connectors and locations vary based upon the model. A

GPSMAP 8612xsv model is shown below.

2 microSD® memory card slots, 32 GB max.

NETWORK Garmin Marine Network

HDMI IN HDMI® in

HDMI OUT HDMI out

CVBS IN Composite video in

AUDIO NMEA® 0183 and audio out

POWER Power

USB Micro-USB to connect a compatible Garmin card reader,

or to connect and control a computer using the chart-

plotter touchscreen

12-PIN XDCR 12-pin transducer

LVS XDCR LiveScope™ single-array transducer

8-PIN XDCR 8-pin transducer

NMEA 2000 NMEA 2000® network

J1939 J1939 network

Introduction 1

Connector View (8x17, 8x22, and 8x24 models)

The connectors and locations vary based upon the model. A

GPSMAP 8622 model is shown below.

POWER Power

NETWORK Garmin Marine Network

HDMI IN HDMI in

HDMI OUT HDMI out

CVBS IN Composite video in

NMEA 0183 NMEA 0183 and audio out

USB Micro-USB to connect a compatible Garmin card

reader, or to connect and control a computer using the

chartplotter touchscreen

NMEA 2000 NMEA 2000 network

ENGINE/J1939 J1939 engine network

Connector View (8700 models)

POWER Power cable connection

NETWORK Garmin Marine Network

HDMI IN HDMI in

HDMI OUT HDMI out to connect the chartplotter to a monitor.

Required for device functionality.

CVBS IN Composite video in

Status LED

Power ground

Power button

NMEA 0183 NMEA 0183 and audio out

USB HOST Micro-USB output for connecting a touchscreen monitor

USB OTG Micro-USB input from compatible Garmin card reader1,

computer, or other supported USB accessory

NMEA 2000 NMEA 2000 network

J1939 J1939 network

Tips and Shortcuts (MFD models)

• Press to turn on the chartplotter.

• From any screen, press repeatedly to scroll through the

brightness levels, if available. This can be helpful when the

brightness is so low you cannot see the screen.

• Select Home from any screen to return to the Home screen.

• Select Menu to open additional settings about that screen.

• Select Menu to close the menu when finished.

1 Only compatible Garmin card readers recommended. Third-party card readers

are not guaranteed to be fully compatible.

• Press to open additional options, such as locking the

touchscreen.

• Press , and select Power > Turn Off System, or hold

until the Turn Off System bar fills to turn off the chartplotter,

when available.

• Press , and select Power > Sleep Station to set the

chartplotter to standby mode, when available.

• On the home screen of some models, swipe up or down on

the category buttons along the right side of the screen to view

the additional buttons.

On some models, not all category buttons are visible. The

arrows at the top or bottom of the buttons indicate not all

buttons are visible.

• On some menu buttons, select the button to enable the

option.

A green light on an option indicates the option is enabled .

• When available, select the arrow to open the menu.

Tips and Shortcuts (8700 model)

• Press on the GPSMAP 8700 device to turn it on and off.

You can also turn the device off using a Garmin chartplotter

on the network, a GMM™ monitor, or a GRID™ remote.

You can put the device to sleep using the GRID 20 remote.

• Select Home from any screen to return to the home screen.

• Select Menu to open additional settings about that screen.

• Select Menu to close the menu when finished.

• When the device is sleeping, touch the screen to wake the

device.

• Press to open additional options, such as locking the

touchscreen.

• From any screen, press repeatedly to scroll through the

brightness levels when connected to a Garmin GMM monitor,

a GRID remote, or a GRID 20 remote. This can be helpful

when the brightness is so low you cannot see the screen.

• On the home screen, swipe up or down on the category

buttons along the right side of the screen to view the

additional buttons.

Not all category buttons are visible. The arrows at the top or

bottom of the buttons indicate not all buttons are visible.

• On some menu buttons, select the button to enable the

option.

A green light on an option indicates the option is enabled .

• When available, select the arrow to open the menu.

Accessing Owner's Manuals on the

Chartplotter

1Select Info > Owner's Manual.

2Select a manual.

3Select Open.

2 Introduction

Downloading the Manuals from the Web

You can get the latest owner's manual and translations of

manuals from the Garmin website. The owner's manual includes

instructions for using device features and accessing regulatory

information.

1Go to garmin.com/manuals/GPSMAP8400-8600.

2Download the manual.

Garmin Support Center

Go to support.garmin.com for help and information, such as

product manuals, frequently asked questions, videos, software

updates, and customer support.

Memory Cards

You can use optional memory cards with the chartplotter. Map

cards allow you to view high-resolution satellite imagery and

aerial reference photos of ports, harbors, marinas, and other

points of interest. You can use blank memory cards to record

Garmin Quickdraw™ Contours mapping, record sonar (with a

compatible transducer), transfer data such as waypoints and

routes to another compatible chartplotter or a computer, and use

the ActiveCaptain® app.

This device supports up to a 32 GB memory card, formatted to

FAT32 with speed class 4 or higher. Use of an 8 GB or higher

memory card with speed class 10 is recommended. An 8 GB

memory card is included with GPSMAP 8x10/8x12/8x16 models.

Model Memory Card Location Memory Card Type

8x10 Back of the device microSD

8x12 Back of the device microSD

8x16 Back of the device microSD

8x17 External card reader SD®

8x22 External card reader SD

8x24 External card reader SD

87xx External card reader SD

Inserting Memory Cards (GPSMAP 8x10/8x12/8x16)

This device supports up to a 32 GB microSD memory card,

formatted to FAT32 with speed class 4 or higher. Use of an 8

GB or higher memory card with speed class 10 is

recommended. An 8 GB memory card is included with GPSMAP

8x10/8x12/8x16 models.

1Open the weather cap on the back of the chartplotter.

2Insert the memory card .

3Press the card in until it clicks.

4Press the weather cap firmly shut to prevent corrosion.

Inserting a Memory Card (GPSMAP

8x17/8x22/8x24/87xx)

NOTE: The memory card reader is not included with the

chartplotter. It is sold as a separate accessory. You must

connect a memory card reader or a chartplotter model with a

built-in memory card slot to the Garmin Marine Network.

This device supports up to a 32 GB SD memory card, formatted

to FAT32 with speed class 4 or higher. Use of an 8 GB or higher

memory card with speed class 10 is recommended. A memory

card is not included with GPSMAP 8x17/8x22/8x24/87xx

models.

1Open the door on the memory card reader.

2Insert the memory card with the label facing away from the

door.

3Press the card in until it clicks.

4Close the card reader door.

Acquiring GPS Satellite Signals

The device may need a clear view of the sky to acquire satellite

signals. The time and date are set automatically based on the

GPS position.

1Turn on the device.

2Wait while the device locates satellites.

It may take 30 to 60 seconds to acquire satellite signals.

When the device acquires satellite signals, appears at the

top of the Home screen.

If the device loses satellite signals, disappears and a

flashing question mark appears over on the chart.

For more information about GPS, go to garmin.com/aboutGPS.

For help acquiring satellite signals, see My device will not

acquire GPS signals, page 69.

Selecting the GPS Source

You can select your preferred source for GPS data, if you have

more than one GPS source.

1Select Settings > System > GPS > Source.

2Select the source for GPS data.

Customizing the Chartplotter

Home Screen

The chartplotter home screen provides access to all of the

features in the chartplotter. The features are dependant on the

accessories you have connected to the chartplotter. You may

not have all of the options and features discussed in this

manual.

When viewing another screen, you can return to the home

screen by selecting Home.

Status bar

Pages buttons

Customizing the Chartplotter 3

Categories bar

Menu bar

The categories along the right of the screen provide quick

access to the main features of your chartplotter. For example,

the Sonar category displays the views and pages related to the

sonar feature. You can save items you commonly access to the

Favorites category.

TIP: If your home screen has been customized by the boat

manufacturer, you can open the original home page category

tabs by dragging the bar on the right side of the screen to the

left.

The SmartMode items are geared toward an activity, such as

cruising or docking. When a SmartMode button is selected from

the home screen, each display in the station can show unique

information. For example, when Cruising is selected from the

home screen, one display can show the navigation chart and

another display can show the radar screen.

All of the options along the bottom of the home screen are

visible on all other screens, except for the Settings button. The

Settings button is accessible only from the home screen.

An indicator appears on the Info button when an alarm is

activated (Warning Manager, page 51).

When multiple displays are installed on the Garmin Marine

Network, you can group them together into a station. A station

enables the displays to work together, instead of as several

separate displays. You can customize the layout of the pages on

each display, making each page different on each display. When

you change the layout of a page in one display, the changes

appear on only that display. When you change the name and

symbol of the layout, those changes appear on all displays in

the station, to maintain a consistent appearance.

Adding an Item to Favorites

You can add items such as a chart, combo screen, or gauge to

the Favorites category.

NOTE: If your home screen has been customized by the boat

manufacturer, you cannot add an item to the Favorites category.

1From the home screen, select a category from the right.

2Hold a button on the left.

The item is added to the Favorites home screen category.

To remove an item you have added to the Favorites category,

open the Favorites category, select Menu > Remove Favorite,

and select the item to remove.

Customizing the Home Screen

1Open the home screen category to customize.

2Select Menu.

3Select an option:

• To rearrange an item, select Rearrange, and select the

new location.

• To add an item to the Favorites category, select Add to

Favorites, and select the item.

• To change the home screen background image, select

Background, and select an image.

Customizing Pages

Customizing the Layout of a SmartMode or

Combination Page

You can customize the layout and data shown in the

combination pages and SmartMode layouts. When you change

the layout of a page in a display you are interacting with, the

change appears only on that display, except for the SmartMode

name and symbol. When you change the SmartMode name or

symbol for the layout, the new name or symbol appears on all

displays in the station.

1Open a page to customize.

2Select Menu.

3Select Edit Layout or Edit Combo.

4Select an option:

• To change the name, select Name or Name & Symbol >

Name, enter a new name, and select Done.

• To change the SmartMode symbol, select Name &

Symbol > Symbol, and select a new symbol.

• To change the number of functions shown and the layout

of the screen, select Layout, and select an option.

• To change the function of a portion of the screen, select

the window to change, and select a function from the list

on the right.

• To change how the screens are split, drag the arrows to a

new location.

• To change the data shown on the page and additional

data bars, select Overlays, and select an option.

TIP: While viewing a screen with data overlay, hold an

overlay box to quickly change the data in it.

• To assign a preset to a portion of the SmartMode screen,

select Presets > Include, and select a preset from the list

on the right.

Changing the Background Image

1From the home screen, select Menu > Background.

TIP: You can also adjust this setting from Settings > System

> Sounds and Display > Background.

2Select an image.

Customizing the Startup Screen

You personalize the image that is displayed when the

chartplotter is turning on. For the best fit, the image should be

50 MB or less and conform to the recommended dimensions

(Recommended Startup Image Dimensions, page 4).

1Insert a memory card that contains the image you want to

use.

2Select Settings > System > Sounds and Display > Startup

Image > Select Image.

3Select the memory card slot.

4Select the image.

5Select Set as Startup Image.

The new image is shown then turning on the chartplotter.

Recommended Startup Image Dimensions

For the best fit for the startup images, use an image that has the

following dimensions, in pixels.

Display resolution Image width Image height

WVGA 680 200

WSVGA 880 270

WXGA 1080 350

HD 1240 450

WUXGA 1700 650

Adding a SmartMode Layout

You can add SmartMode layouts to suit your needs. Each

customization made to one SmartMode layout for the home

screen in a station appears on all displays in the station.

1From the home screen, select SmartMode™ > Menu > Add

Layout.

2Select an option:

• To change the name, select Name & Symbol > Name,

enter a new name, and select Done.

4 Customizing the Chartplotter

• To change the SmartMode symbol, select Name &

Symbol > Symbol, and select a new symbol.

• To change the number of functions shown and the layout

of the screen, select Layout, and select an option.

• To change the function of a portion of the screen, select

the window to change, and select a function from the list

on the right.

• To change how the screens are split, drag the arrows to a

new location.

• To change the data shown on the page and additional

data bars, select Overlays, and select an option.

• To assign a preset to a portion of the SmartMode screen,

select Presets > Include, and select a preset from the list

on the right.

Creating a New Combination Page

You can create a custom combination page to suit your needs.

1Select Combos > Menu > Add Combo.

2Select a window.

3Select a function for the window.

4Repeat these steps for each window of the page.

5Drag the arrows to resize the windows.

6Hold a window to rearrange it.

7Hold a data field to select new data.

8Select Layout, and select a layout.

9Select Name, enter a name for the page, and select Done.

10Select Overlays, and select which data to show.

11Select Done when you have finished customizing the page.

Deleting a Combination Page

1Select Combos > Menu > Delete Combo.

2Select a combination.

Customizing the Data Overlays

You can customize the data in the data overlays shown on a

screen.

1Select an option based on the type of screen you are

viewing:

• From a full screen view, select Menu > Edit Overlays.

• From a combination screen, select Menu > Edit Combo >

Edit Overlays.

• From a SmartMode screen, select Menu > Edit Layout.

TIP: To quickly change the data shown in an overlay box,

hold the overlay box.

2Select an item to customize the data and data bar:

• To change the data shown in an overlay box, select the

overlay box, select the new data to show, and select

Back.

• To select the location and layout of the data overlay bar,

select Edit Layout, and select an option.

• To customize the information shown when navigating,

select Navigation, and select an option.

• To turn on other data bars, like the media controls, select

Top Bar or Bottom Bar, and select the necessary

options.

3Select Done.

Resetting the Station Layouts

You can restore the layouts in this station to the factory default

settings.

Select Settings > System > Station Information > Reset

Layouts.

Presets

A preset is a collection of settings that optimize the screen or

view. You can use particular presets to optimize groups of

settings for your activity. For example, some settings might be

optimal for when you are fishing, and others might be optimal for

when you are cruising. Presets are available on some screens,

such as charts, sonar views, and radar views.

To select a preset for a compatible screen, select Menu > ,

and select the preset.

When you are using a preset and you make changes to the

settings or view, you can save the changes to the preset or

create a new preset based on the new customizations.

Saving a New Preset

After you have customized the settings and view of a screen,

you can save the customization as a new preset.

1From a compatible screen, change the settings and view.

2Select Menu > > Save > New.

3Enter a name, and select Done.

4Select an item, and select Include to include or exclude the

item from the preset.

Managing Presets

You can customize the pre-loaded presets and edit presets you

created.

1From a compatible screen, select Menu > > Manage.

2Select a preset.

3Select an option:

• To rename the preset, select Rename, enter a name, and

select Done.

• To edit the preset, select Edit, and update the preset.

• To delete the preset, select Delete.

• To reset all presets to factory settings, select Reset All.

Setting the Vessel Type

You can select your boat type to configure the chartplotter

settings and to use features customized for your boat type.

1Select Settings > My Vessel > Vessel Type.

2Select an option.

Adjusting the Backlight

1Select Settings > System > Display > Backlight.

2Adjust the backlight.

Customizing the Chartplotter 5

TIP: From any screen, press repeatedly to scroll through

the brightness levels. This can be helpful when the

brightness is so low you cannot see the screen.

Adjusting the Color Mode

1Select Settings > System > Sounds and Display > Color

Mode.

TIP: Select > Color Mode from any screen to access the

color settings.

2Select an option.

Turning On the Chartplotter Automatically

You can set the chartplotter to turn on automatically when the

power is applied. Otherwise, you must turn on the chartplotter by

pressing .

Select Settings > System > Auto Power Up.

NOTE: When Auto Power Up is On, and the chartplotter is

turned off using , and power is removed and reapplied

within less than two minutes, you may need to press to

restart the chartplotter.

Enabling Screen Lock

For anti-theft protection and to prevent unauthorized use of your

device, you can enable the Screen Lock feature which requires

a PIN (Personal Identification Number). When enabled, you

must enter the PIN to unlock the screen each time you turn on

the device. You can set up recovery questions and answers as

prompts in case you forget the PIN.

NOTICE

If you enable the Screen Lock feature, Garmin Support cannot

retrieve the PIN or access your device. It is your responsibility to

provide the PIN to anyone authorized to use the vessel.

1Select Settings > System > Sounds and Display > Screen

Lock > Setup.

2Enter a memorable numeric PIN of 6 digits.

3Reenter the PIN to verify.

4When prompted, choose and answer three PIN recovery

questions.

You can Disable or Reset the PIN and recovery questions as

needed.

Automatically Turning Off the System

You can set the chartplotter and the whole system to turn off

automatically after it has been asleep for the selected length of

time. Otherwise, you must press and hold to turn off the

system manually.

1Select Settings > System > Auto Power Off.

2Select an option.

ActiveCaptain App

CAUTION

This feature allows users to submit information. Garmin makes

no representations about the accuracy, completeness, or

timeliness of information submitted by users. Any use or reliance

on the information submitted by users is at your own risk.

The ActiveCaptain app provides a connection to your GPSMAP

device, charts, maps, and the community for a connected

boating experience.

On your mobile device with the ActiveCaptain app, you can

download, purchase, and update maps and charts. You can use

the app to easily and quickly transfer user data, such as

waypoints and routes, connect to the Garmin Quickdraw

Contours Community, update device software, and plan your

trip.

You can connect to the ActiveCaptain community for up-to-date

feedback on marinas and other points of interest. The app can

push smart notifications, such as calls and texts, to your

chartplotter display when paired.

ActiveCaptain Roles

Your level of interaction with the GPSMAP device using the

ActiveCaptain app depends on your role.

Feature Owner Guest

cards to account

Yes No

Update software Yes Yes

Automatically transfer Garmin Quickdraw contours you

have downloaded or created

Yes No

Push smart notifications Yes Yes

Automatically transfer user data, such as waypoints

and routes

Yes No

Begin navigating to a specific waypoint or navigating a

specific route, and send that waypoint or route to the

GPSMAP device

Yes Yes

Getting Started with the ActiveCaptain App

You can connect a mobile device to the GPSMAP device using

the ActiveCaptain app. The app provides a quick and easy way

for you to interact with your GPSMAP device and complete such

tasks as sharing data, registering, updating the device software,

and receiving mobile device notifications.

1From the GPSMAP device, select OneHelm™, A/V, Gauges

> ActiveCaptain.

2From the ActiveCaptain page, select Wi-Fi Network > Wi-Fi

> On.

3Enter a name and password for this network.

4Insert a memory card in the GPSMAP device's card slot

(Memory Cards, page 3).

5Select Set ActiveCaptain Card.

NOTICE

You might be prompted to format the memory card.

Formatting the card deletes all information saved on the card.

This includes any saved user data, such as waypoints.

Formatting the card is recommended, but not required.

Before formatting the card, you should save the data from the

memory card onto the device internal memory (Copying User

Data from a Memory Card, page 65). After formatting the

card for the ActiveCaptain app, you can transfer the user

data back to the card (Copying User Data to a Memory Card,

page 65).

Be sure the card is inserted each time you want to use the

ActiveCaptain feature.

6From the application store on your mobile device, install and

open the ActiveCaptain app.

7Bring the mobile device within 32 m (105 ft.) of the GPSMAP

device.

8From your mobile device settings, open the Wi‑Fi®

connections page and connect to the Garmin device, using

the name and password you entered in the Garmin device.

Enabling Smart Notifications

WARNING

Do not read or reply to notifications while operating the vessel.

Failure to pay attention to the conditions on the water can result

in vessel damage, personal injury, or death.

6 ActiveCaptain App

Before your GPSMAP device can receive notifications, you must

connect it to your mobile device and to the ActiveCaptain app.

1From the GPSMAP device, select ActiveCaptain > Smart

Notifications > Enable Notifications.

2Turn on Bluetooth® technology in the mobile device settings.

3Bring the devices within 10 m (33 ft.) of each other.

4From the ActiveCaptain app on the mobile device, select

Smart Notifications > Pair with Chartplotter.

5Follow the on-screen instructions to pair the app to the

GPSMAP device.

6When prompted, enter the key on your mobile device.

7If necessary, adjust which notifications you receive in your

mobile device settings.

Receiving Notifications

WARNING

Do not read or reply to notifications while operating the vessel.

Failure to pay attention to the conditions on the water can result

in vessel damage, personal injury, or death.

Before your GPSMAP device can receive notifications, you must

connect it to your mobile device and enable the Smart

Notifications feature (Enabling Smart Notifications, page 6).

When the Smart Notifications feature is enabled and your mobile

device receives a notification, a pop-up notification appears on

the GPSMAP screen briefly.

NOTE: The available actions depend on the type of notification

and your phone operating system.

• To answer a phone call on your phone, select Answer.

TIP: Have your phone nearby. The phone call is answered on

your mobile phone, not on the chartplotter.

• To not answer the phone call, select Decline.

• To review the full message, select Review.

• To dismiss the pop-up notification, select OK or wait for the

notification to close automatically.

• To remove the notification from the chartplotter and your

mobile device, select Clear.

Managing Notifications

WARNING

Do not read or reply to notifications while operating the vessel.

Failure to pay attention to the conditions on the water can result

in vessel damage, personal injury, or death.

Before you can manage the notifications, you must enable the

Smart Notifications feature (Enabling Smart Notifications,

page 6).

When the Smart Notifications feature is enabled and your mobile

device receives a notification, a pop-up notification appears on

the GPSMAP screen briefly. You can access and manage the

notifications from the ActiveCaptain screen.

1Select ActiveCaptain > Smart Notifications > Messages.

A list of notifications appear.

2Select a notification.

3Select an option:

NOTE: The available options vary based on your mobile

device and the notification type.

• To dismiss and remove the notification from the

chartplotter and your mobile device, select Clear or

Delete.

NOTE: This does not delete the message from the mobile

device. This only dismisses and removes the notification.

• To call the phone number back, select Call Back or Dial.

Making Notifications Private

You can turn off the pop-up notifications and disable the

messages list on specific chartplotters for privacy. For example,

the captain could disable pop-up notifications and messages on

the chartplotter used for fishing, but allow notifications on the

chartplotter used at the helm.

1From the chartplotter you want notifications to be private,

select ActiveCaptain > Smart Notifications.

2Select an option:

• To turn off pop-up notifications on this chartplotter, select

Popups.

• To turn off pop-up notifications and disable access to the

messages list on this chartplotter, select Visibility.

Updating Software with the ActiveCaptain

App

If your device has Wi‑Fi technology, you can use the

ActiveCaptain app to download and install the latest software

updates for your device.

NOTICE

Software updates may require the app to download large files.

Regular data limits or charges from your Internet service

provider apply. Contact your Internet service provider for more

information about data limits or charges.

The installation process can take several minutes.

1Connect the mobile device to the GPSMAP device (Getting

Started with the ActiveCaptain App, page 6).

2When a software update is available and you have internet

access on your mobile device, select Software Updates >

Download.

The ActiveCaptain app downloads the update to the mobile

device. When you reconnect the app to the GPSMAP device,

the update is transferred to the device. After the transfer is

complete, you are prompted to install the update.

3When you are prompted by the GPSMAP device, select an

option to install the update.

• To update the software immediately, select OK.

• To delay the update, select Cancel. When you are ready

to install the update, select ActiveCaptain > Software

Updates > Install Now.

Updating Charts with ActiveCaptain

You can use the ActiveCaptain app to download and transfer the

latest chart updates for your device. To save space on your

mobile device, space on the ActiveCaptain card, and download

time, consider using the ActiveCaptain app to download only the

areas of the chart you need.

If you are downloading an entire chart, you can use the Garmin

Express™ app to download the map onto a memory card

(Updating Your Charts Using the Garmin Express App,

page 67). The Garmin Express app downloads large charts

more quickly than the ActiveCaptain app.

NOTICE

Chart updates may require the app to download large files.

Regular data limits or charges from your internet service

provider apply. Contact your internet service provider for more

information about data limits or charges.

1Connect the mobile device to the GPSMAP device (Getting

Started with the ActiveCaptain App, page 6).

2When a chart update is available, and you have internet

access on your mobile device, select OneChart > My

Charts.

3Select the map to update.

ActiveCaptain App 7

4Select the area to download.

5Select Download.

The ActiveCaptain app downloads the update to the mobile

device. When you reconnect the app to the GPSMAP device,

the update is transferred to the device. After the transfer is

complete, the updated charts are available for use.

Communication with Wireless Devices

The chartplotters can create a wireless network to which you

can connect wireless devices.

Connecting wireless devices allows you to use Garmin apps,

such as ActiveCaptain.

Wi‑Fi Network

Setting Up the Wi‑Fi Wireless Network

The chartplotters can create a Wi‑Fi network to which you can

connect wireless devices. The first time you access the wireless

network settings, you are prompted to set up the network.

1Select Settings > Communications > Wi-Fi Network > Wi-

Fi > On > OK.

2If necessary, enter a name for this wireless network.

3Enter a password.

You will need this password to access the wireless network

from a wireless device. The password is case-sensitive.

Connecting a Wireless Device to the Chartplotter

Before you can connect a wireless device to the chartplotter

wireless network, you must configure the chartplotter wireless

network (Setting Up the Wi

‑

Fi Wireless Network, page 8).

You can connect multiple wireless devices to the chartplotter to

share data.

1From the wireless device, turn on the Wi‑Fi technology and

search for wireless networks.

2Select the name of your chartplotter wireless network (Setting

Up the Wi

‑

Fi Wireless Network, page 8).

3Enter the chartplotter password.

Changing the Wireless Channel

You can change the wireless channel if you have trouble finding

or connecting to a device, or if you experience interference.

1Select Settings > Communications > Wi-Fi Network >

Advanced > Channel.

2Enter a new channel.

You do not need to change the wireless channel of devices

connected to this network.

Changing the Wi‑Fi Host

If there are multiple chartplotters with Wi‑Fi technology on the

Garmin marine network, you can change which chartplotter is

the Wi‑Fi host. This can be helpful if you are having trouble with

Wi‑Fi communications. Changing the Wi‑Fi host allows you to

select a chartplotter that is physically closer to your mobile

device.

1Select Settings > Communications > Wi-Fi Network >

Advanced > Wi-Fi Host.

2Follow the on-screen instructions.

Wireless Remote Control

These steps are not applicable to the GRID remote input

devices (Pairing the GRID Device with the Chartplotter from the

Chartplotter, page 69).

Pairing the Wireless Remote Control With the

Chartplotter

Before you can use the wireless remote control with a

chartplotter, you must pair the remote with the chartplotter.

You can connect a single remote to multiple plotters, and then

press the pairing key to switch between the chartplotters.

1Select Settings > Communications > Wireless Devices >

Wireless Remotes > GPSMAP® Remote.

2Select New Connection.

3Follow the on-screen instructions.

Turning On and Off the Remote Backlight

Turning off the remote backlight can significantly increase the

battery life.

1On the chartplotter, select Settings > Communications >

Wireless Devices > Wireless Remotes > GPSMAP®

Remote > Backlight.

2Follow the on-screen instructions.

Disconnecting the Remote from All Chartplotters

1On the chartplotter, select Settings > Communications >

Wireless Devices > Wireless Remotes > GPSMAP®

Remote > Disconnect All.

2Follow the on-screen instructions.

Wireless Wind Sensor

Connecting a Wireless Sensor to the Chartplotter

You can view data from a compatible wireless sensor on the

chartplotter.

1Select Settings > Communications > Wireless Devices.

2Select the wind sensor.

3Select Enable.

The chartplotter begins searching for and connecting to the

wireless sensor.

To view data from the sensor, add the data to a data field or

gauge.

Adjusting the Wind Sensor Orientation

You should adjust this setting if the sensor does not face the

front of the boat, exactly parallel to the center line.

NOTE: The opening where the cable connects to the pole

indicates the front of the sensor.

1Estimate the angle, in degrees clockwise around the mast, by

which the sensor points away from the center of the front of

the boat:

• If the sensor is facing starboard, the angle should be

between 1 and 180 degrees.

• If the sensor is facing port, the angle should be between

-1 and -180 degrees.

2Select Settings > Communications > Wireless Devices.

3Select the wind sensor.

4Select Wind Angle Offset.

5Enter the angle observed in step 1.

6Select Done.

Viewing Boat Data on a Garmin Watch

You can connect a compatible Garmin watch to a compatible

chartplotter to view data from the chartplotter.

1Bring the Garmin watch within range (3 m) of the chartplotter.

2From the watch clock screen, select START > Boat Data >

START.

8 Communication with Wireless Devices

NOTE: If you have already connected to a chartplotter, and

would like to connect to a different chartplotter, open the Boat

Data screen, hold UP, and select Pair new.

3On the chartplotter, select Communications > Wireless

Devices > Connect IQ™ Apps > Boat Data > Enable >

New Connection.

The chartplotter begins searching for and connecting to the

wearable device.

4Compare the code shown on the chartplotter with the one

shown on the watch.

5If the codes match, select Yes to complete the pairing

process.

After the devices are paired, they connect automatically when

they are turned on and within range.

Viewing Boat Data on a Garmin Nautix™

Device

You can connect a Garmin Nautix device to the chartplotter to

view charplotter data on the Garmin Nautix device.

NOTE: You can connect a Garmin Nautix device to multiple

compatible devices for better coverage on larger vessels.

1Bring the a Garmin Nautix device within range (3 m) of the

chartplotter.

The device automatically looks for all compatible devices

within range.

2If necessary, from the wearable device menu, select Device

Connections > Pair New Device.

3On the chartplotter, select Settings > Communications >

Wireless Devices > Connect IQ™ Apps > Boat Data >

Enable Connections > New Connection.

The chartplotter begins searching for and connecting to the

wearable device.

After the devices are paired, they connect automatically when

they are turned on and within range.

Charts and 3D Chart Views

The charts and 3D chart views that are available depend on the

map data and accessories used.

NOTE: 3D chart views are available with premium charts, in

some areas.

You can access the charts and 3D chart views by selecting

Charts.

Nav. Chart: Shows navigation data available on your pre-loaded

maps and from supplemental maps, if available. The data

includes buoys, lights, cables, depth soundings, marinas, and

tide stations in an overhead view.

Fishing Chart: Provides a detailed view of the bottom contours

and depth soundings on the chart. This chart removes

navigational data from the chart, provides detailed

bathymetric data, and enhances bottom contours for depth

recognition. This chart is best for offshore deep-sea fishing.

NOTE: The Fishing chart is available with premium charts, in

some areas.

Perspective 3D: Provides a view from above and behind the

boat (according to your course) and provides a visual

navigation aid. This view is helpful when navigating tricky

shoals, reefs, bridges, or channels, and is beneficial when

trying to identify entry and exit routes in unfamiliar harbors or

anchorages.

3D Chart: Shows a detailed, three-dimensional view from above

and behind the boat (according to your course) and provides

a visual navigation aid. This view is helpful when navigating

tricky shoals, reefs, bridges, or channels, and when trying to

identify entry and exit routes in unfamiliar harbors or

anchorages.

Fish Eye 3D: Provides an underwater view that visually

represents the sea floor according to the chart information.

When a sonar transducer is connected, suspended targets

(such as fish) are indicated by red, green, and yellow

spheres. Red indicates the largest targets and green

indicates the smallest.

Relief Shading: Provides high resolution elevation shading of

lakes and coastal waters. This chart can be helpful for fishing

and diving.

NOTE: The Relief Shading chart is available with premium

charts, in some areas.

Navigation Chart and Fishing Chart

NOTE: The Fishing chart is available with premium charts, in

some areas.

The Nav. Chart is optimized for navigation. You can plan a

course, view map information, and use the chart as a

navigational aid. To open the Nav. Chart, select Charts > Nav.

Chart.

The Fishing Chart provides a detailed view with more bottom

detail and fishing content. This chart is optimized for use when

fishing. To open the Fishing Chart, select Charts > Fishing

Chart.

Zooming In and Out Using the Touchscreen

You can quickly zoom in and out of many screens, such as the

charts and sonar views.

• Pinch two fingers together to zoom out.

• Spread two fingers apart to zoom in.

Chart Symbols

This table contains some of the common symbols you might see

on the detailed charts.

Icon Description

Buoy

Information

Marine services

Tide station

Current station

Overhead photo available

Perspective photo available

Other features common to most charts include depth contour

lines, intertidal zones, spot soundings (as depicted on the

original paper chart), navigational aids and symbols,

obstructions, and cable areas.

Measuring a Distance on the Chart

1From a chart, select a location.

2Select Measure.

A push pin appears on the screen at your present location.

The distance and angle from the pin is listed in the corner.

TIP: To reset the pin and measure from the current location of

the cursor, select Set Reference.

Charts and 3D Chart Views 9

Creating a Waypoint on the Chart

1From a chart, select a location or object.

2Select .

Viewing Location and Object Information on a Chart

You can view information, such as tide, current, celestial, chart

notes, or local services, about a location or an object on the

Navigation chart or the Fishing chart.

1From the Navigation chart or Fishing chart, select a location

or object.

A list of options appears. The options that appear vary based

on the location or object you selected.

2If necessary, select .

3Select Information.

Viewing Details about Navaids

From the Navigation chart, Fishing chart, Perspective 3D chart

view, or Mariner’s Eye 3D chart view, you can view details about

various types of navigation aids, including beacons, lights, and

obstructions.

NOTE: The Fishing chart is available with premium charts, in

some areas.

NOTE: 3D chart views are available with premium charts, in

some areas.

1From a chart or 3D chart view, select a navaid.

2Select the name of the navaid.

Navigating to a Point on the Chart

WARNING

All route and navigation lines displayed on the chartplotter are

only intended to provide general route guidance or to identify

proper channels, and are not intended to be precisely followed.

Always defer to the navaids and conditions on the water when

navigating to avoid groundings or hazards that could result in

vessel damage, personal injury, or death.

The Auto Guidance feature is based on electronic chart

information. That data does not ensure obstacle and bottom

clearance. Carefully compare the course to all visual sightings,

and avoid any land, shallow water, or other obstacles that may

be in your path.

When using Go To, a direct course and a corrected course may

pass over land or shallow water. Use visual sightings, and steer

to avoid land, shallow water, and other dangerous objects.

NOTE: The Fishing chart is available with premium charts, in

some areas.

NOTE: Auto Guidance is available with premium charts, in some

areas.

1From the Navigation chart or Fishing chart, select a location.

2If necessary, select Navigate To.

3Select an option:

• To navigate directly to the location, select Go To or .

• To create a route to the location, including turns, select

Route To or .

• To use Auto Guidance, select Auto Guidance or .

4Review the course indicated by the magenta line.

NOTE: When using Auto Guidance, a gray segment within

any part of the magenta line indicates that Auto Guidance

cannot calculate part of the Auto Guidance line. This is due to

the settings for minimum safe water depth and minimum safe

obstacle height.

5Follow the magenta line, steering to avoid land, shallow

water, and other obstacles.

Premium Charts

WARNING

All route and navigation lines displayed on the chartplotter are

only intended to provide general route guidance or to identify

proper channels, and are not intended to be precisely followed.

Always defer to the navaids and conditions on the water when

navigating to avoid groundings or hazards that could result in

vessel damage, personal injury, or death.

The Auto Guidance feature is based on electronic chart

information. That data does not ensure obstacle and bottom

clearance. Carefully compare the course to all visual sightings,

and avoid any land, shallow water, or other obstacles that may

be in your path.

NOTE: Not all models support all charts.

Optional premium charts, such as BlueChart® g3 Vision, allow

you to get the most out of your chartplotter. In addition to

detailed marine charting, premium charts may contain these

features, which are available in some areas.

Mariner’s Eye 3D: Provides a view from above and behind the

boat for a three-dimensional navigation aid.

Fish Eye 3D: Provides an underwater, three-dimensional view

that visually represents the sea floor according to the

information on the chart.

Fishing Charts: Shows the chart with enhanced bottom

contours and without navigational data. This chart works well

for offshore deep-sea fishing.

High Resolution Satellite Imagery: Provides high-resolution

satellite images for a realistic view of the land and water on

the Navigation chart (Showing Satellite Imagery on the

Navigation Chart, page 11).

Aerial Photos: Shows marinas and other navigationally

significant aerial photos to help you visualize your

surroundings (Viewing Aerial Photos of Landmarks,

page 11).

Detailed Roads and POI data: Shows detailed road and point

of interest (POI) data, which includes highly detailed coastal

roads and POIs such as restaurants, lodging, and local

attractions.

Auto Guidance: Uses specified information about your vessel

and chart data to determine the best path to your destination.

Fish Eye 3D Chart View

Using the depth contour lines of the premium charts, such as

BlueChart g3 Vision, the Fish Eye 3D chart view provides an

underwater view of the sea floor or lake bottom.

Suspended targets, such as fish, are indicated by red, green,

and yellow spheres. Red indicates the largest targets and green

indicates the smallest.

Viewing Tide Station Information

WARNING

Tide and current information is for information purposes only. It

is your responsibility to heed all posted water-related guidance,

to remain aware of your surroundings, and to use safe judgment

in, on, and around the water at all times. Failure to heed this

warning could result in property damage, serious personal

injury, or death.

10 Charts and 3D Chart Views

The icon on the chart indicates a tide station. You can view a

detailed graph for a tide station to help predict the tide level at

different times or on different days.

NOTE: This feature is available with premium charts, in some

areas.

1From the Navigation chart or Fishing chart, select a tide

station.

Tide direction and tide level information appear near .

2Select the station name.

Animated Tide and Current Indicators

WARNING

Tide and current information is for information purposes only. It

is your responsibility to heed all posted water-related guidance,

to remain aware of your surroundings, and to use safe judgment

in, on, and around the water at all times. Failure to heed this

warning could result in property damage, serious personal

injury, or death.

NOTE: This feature is available with premium charts, in some

areas.

You can view indicators for animated tide station and current

direction on the Navigation chart or the Fishing chart. You must

also enable animated icons in the chart settings (Showing Tides

and Current Indicators, page 11).

An indicator for a tide station appears on the chart as a vertical

bar graph with an arrow. A red arrow pointing downward

indicates a falling tide, and a blue arrow pointing upward

indicates a rising tide. When you move the cursor over the tide

station indicator, the height of the tide at the station appears

above the station indicator.

Current direction indicators appear as arrows on the chart. The

direction of each arrow indicates the direction of the current at a

specific location on the chart. The color of the current arrow

indicates the range of speed for the current at that location.

When you move the cursor over the current direction indicator,

the specific current speed at the location appears above the

direction indicator.

Color Current Speed Range

Yellow 0 to 1 knot

Orange 1 to 2 knots

Red 2 or more knots

Showing Tides and Current Indicators

NOTE: This feature is available with premium charts, in some

areas.

You can show static or animated tide and current station

indicators on the Navigation chart or Fishing chart.

1From the Navigation or Fishing chart, select Menu > Layers

> Chart > Tides & Currents.

2Select an option:

• To show animated tide station indicators and animated

current direction indicators on the chart, select Animated.

• To enables the tides and current slider, which sets the

time for which tides and currents are reported on the map,

select Slider.

Showing Satellite Imagery on the Navigation Chart

NOTE: This feature is available with premium charts, in some

areas.

You can overlay high-resolution satellite images on the land or

on both land and sea portions of the Navigation chart.

NOTE: When enabled, high-resolution satellite images are

present only at lower zoom levels. If you cannot see high-

resolution images in your optional chart region, you can select

to zoom in. You also can set the detail level higher by changing

the map zoom detail.

1From the Navigation chart, select Menu > Layers > Chart >

Satellite Photos.

2Select an option:

• Select Land Only to show standard chart information on

the water, with photos overlaying the land.

NOTE: This setting must be enabled to view Standard

Mapping® charts.

• Select Photo Map to show photos on both the water and

the land at a specified opacity. Use the slider bar to adjust

the photo opacity. The higher you set the percentage, the

more the satellite photos cover both land and water.

Viewing Aerial Photos of Landmarks

Before you can view aerial photos on the Navigation chart, you

must turn on the Photo Points setting in the chart setup (Chart

Layers, page 13).

NOTE: This feature is available with premium charts, in some

areas.

You can use aerial photographs of landmarks, marinas, and

harbors to help orient yourself to your surroundings or to

acquaint yourself with a marina or a harbor prior to arrival.

1From the Navigation chart, select a camera icon:

• To view an overhead photo, select .

• To view a perspective photo, select . The photo was

taken from the location of the camera, pointed in the

direction of the cone.

2Select Photo.

Automatic Identification System

The Automatic Identification System (AIS) enables you to

identify and track other vessels, and alerts you to area traffic.

When connected to an external AIS device, the chartplotter can

show some AIS information about other vessels that are within

range, that are equipped with a transponder, and that are

actively transmitting AIS information.

The information reported for each vessel includes the Maritime

Mobile Service Identity (MMSI), location, GPS speed, GPS

heading, time that has elapsed since the last position of the

vessel was reported, nearest approach, and time to the nearest

approach.

Some chartplotter models also support Blue Force Tracking.

Vessels being tracked with Blue Force Tracking are indicated on

the chartplotter with a blue-green color.

AIS Targeting Symbols

Symbol Description

AIS vessel. The vessel is reporting AIS information. The

direction in which the triangle is pointing indicates the

direction in which the AIS vessel is moving.

Target is selected.

Target is activated. The target appears larger on the chart. A

green line attached to the target indicates the heading of the

target. The MMSI, speed, and direction of the vessel appear

beneath the target, if the details setting has been set to Show.

If the AIS transmission from the vessel is lost, a message

banner appears.

Target is lost. A green X indicates that the AIS transmission

from the vessel is lost, and the chartplotter displays a

message banner asking whether the vessel should continue

to be tracked. If you discontinue vessel tracking, the lost

target symbol disappears from the chart or the 3D chart view.

Charts and 3D Chart Views 11

Symbol Description

Dangerous target in range. The target flashes while an alarm

sounds and a message banner appears. After the alarm has

been acknowledged, a solid red triangle with a red line

attached to it indicates the location and the heading of the

target. If the safe-zone collision alarm has been set to Off, the

target flashes, but the audible alarm does not sound and the

alarm banner does not appear. If the AIS transmission from

the vessel is lost, a message banner appears.

Dangerous target is lost. A red X indicates that the AIS trans-

mission from the vessel is lost, and the chartplotter displays a

message banner asking whether the vessel should continue

to be tracked. If you discontinue vessel tracking, the lost

dangerous target symbol disappears from the chart or the 3D

chart view.

The location of this symbol indicates the closest point of

approach to a dangerous target, and the numbers near the

symbol indicate the time to the closest point of approach to

that target.

NOTE: Vessels being tracked with the Blue Force Tracking

feature are indicated with a blue-green color regardless of their

status.

Heading and Projected Course of Activated AIS

Targets

When heading and course over ground information are provided

by an activated AIS target, the heading of the target appears on

a chart as a solid line attached to the AIS target symbol. A

heading line does not appear on a 3D chart view.

The projected course of an activated AIS target appears as a

dashed line on a chart or a 3D chart view. The length of the

projected course line is based on the value of the projected

heading setting. If an activated AIS target is not transmitting

speed information, or if the vessel is not moving, a projected

course line does not appear. Changes in the speed, course over

ground, or rate of turn information transmitted by the vessel can

impact the calculation of the projected course line.

When course over ground, heading, and rate of turn information

are provided by an activated AIS target, the projected course of

the target is calculated based on the course over ground and the

rate of turn information. The direction in which the target is

turning, which is also based on the rate of turn information, is

indicated by the direction of the barb at the end of the heading

line. The length of the barb does not change.

When course over ground and heading information are provided

by an activated AIS target, but rate of turn information is not

provided, the projected course of the target is calculated based

on the course over ground information.

Activating a Target for an AIS Vessel

1From a chart or a 3D chart view, select an AIS vessel.

2Select AIS Vessel > Activate Target.

Viewing Information about a Targeted AIS Vessel

You can view the AIS signal status, MMSI, GPS speed, GPS

heading, and other information that is reported about a targeted

AIS vessel.

1From a chart or a 3D chart view, select an AIS vessel.

2Select AIS Vessel.

Deactivating a Target for an AIS Vessel

1From a chart or a 3D chart view, select an AIS vessel.

2Select AIS Vessel > Deactivate.

Viewing a List of AIS and MARPA Threats

1From a chart, select Menu > Layers > Other Vessels > List

> Show.

2Select the type of threats to include in the list.

Setting the Safe-Zone Collision Alarm

CAUTION

The Beeper setting must be turned on to make alarms audible

(Sounds and Display Settings, page 60). Failure to set audible

alarms could lead to injury or property damage.

Before you can set a collision alarm, you must have a

compatible chartplotter connected to an AIS device or radar.

The safe-zone collision alarm is used only with AIS and MARPA.

MARPA functionality works with radar. The safe zone is used for

collision avoidance and can be customized.

1Select Settings > Alarms > Collision Alarm > On.

A message banner appears and an alarm sounds when a

MARPA-tagged object or an AIS-activated vessel enters the

safe-zone area around your boat. The object is also labeled

as dangerous on the screen. When the alarm is off, the

message banner and audible alarm are disabled, but the

object is still labeled as dangerous on the screen.

2Select Range, and select a distance for the safe-zone radius

around your vessel.

3Select Time To, and select a time at which the alarm will

sound if a target is determined to intersect the safe zone.

For example, to be notified of a pending intersection 10

minutes before it will likely occur, set Time To to 10, and the

alarm will sound 10 minutes before the vessel intersects the

safe zone.

4Select MARPA Alarm, and select an option for when the

alarm sounds for MARPA-tagged objects.

AIS Aids to Navigation

An AIS aid to navigation (ATON) is any kind of navigational aid

that is transmitted over the AIS radio. ATONs are displayed on

the charts and have identifying information, such as position and

type.

There are three main kinds of AIS ATONs. Real ATONs

physically exist and send their identifying and location

information from their actual location. Synthetic ATONs

physically exist, and their identifying and location information is

sent from another location. Virtual ATONs do not actually exist,

and their identifying and location information is sent from

another location.

You can view AIS ATONs on the chart when the chartplotter is

connected to a compatible AIS radio. To show AIS ATONs, from

a chart, select Menu > Layers > Chart > Navaid > ATONs. You

can view more information about an ATON if you select the

ATON on the chart.

Symbol Meaning

Real or synthetic ATON

Real or synthetic ATON: Topmark North

Real or synthetic ATON: Topmark South

Real or synthetic ATON: Topmark East

Real or synthetic ATON: Topmark West

Real or synthetic ATON: Topmark Special

Real or synthetic ATON: Topmark Safe

Real or synthetic ATON: Topmark Danger

Virtual ATON

Virtual ATON: Topmark North

12 Charts and 3D Chart Views

This manual suits for next models

Table of contents

Other Garmin GPS manuals

Garmin

Garmin Quest 2 User manual

Garmin

Garmin 796 User manual

Garmin

Garmin GPS 400 User manual

Garmin

Garmin eTrex Touch 25 User manual

Garmin

Garmin iQUE 3600 User guide

Garmin

Garmin Mobile 20 Setup guide

Garmin

Garmin iQUE 3600 User manual

Garmin

Garmin GPS V User manual

Garmin

Garmin GPS 72H Instruction manual

Garmin

Garmin 400/500 User manual

Garmin

Garmin G1000 NXi Owner's manual

Garmin

Garmin Nuvi 3540 Instruction manual

Garmin

Garmin GPS 400W User manual

Garmin

Garmin GDL 69A Installation and operating instructions

Garmin

Garmin DEZL LGV700 User manual

Garmin

Garmin eTrexVista User manual

Garmin

Garmin GPS III Plus Installation and operating instructions

Garmin

Garmin GPSMAP 276C Reference guide

Garmin

Garmin iQUE 3600 User manual

Garmin

Garmin GPS 60 - Hiking GPS Receiver Instruction Manual

Garmin

Garmin nuvi 360 User manual

Garmin

Garmin Approach S6 User manual

Garmin

Garmin Cessna Caravan G1000 User manual

Garmin

Garmin Fishfinder 80 Manual

Popular GPS manuals by other brands

MEDIATEK

MEDIATEK MT3351 manual

Topten

Topten TK218 user manual

LoJack

LoJack EDGE M installation guide

astra telematics

astra telematics AT240 user guide

CanMore

CanMore GPORTER GP-102+ operating instructions

Motorola

Motorola MOTONAV TN500 Series installation guide

Wintec

Wintec WGM-302 user manual

NavCom Technology

NavCom Technology RT-3020 User guide guide

SKYNAV

SKYNAV AT-102 user manual

Nextar

Nextar I4-BC - Automotive GPS Receiver instruction manual

GoPass

GoPass GPS-201 specification

Quick Track

Quick Track OMNI user guide

Sony

Sony nav-u NV-U50 Note

Samsung

Samsung EI-T7300 quick start guide

DayStar

DayStar DS-100c user manual

TeleType GPS

TeleType GPS Mini-Bluetooth GPS Receiver user manual

Teltonika

Teltonika FMT1 manual

switel

switel Vita SOS CT8 user guide

Garmin GPSMAP 87 Series User manual

Popular GPS manuals by other brands