Garmin Quest 2 User manual

To stop or resume the current route:
1. Press the MENU key, highlight Route Options, and press OK. A Route
Options menu appears.
2. Highlight Stop Navigation or Resume Navigation, and press OK to
stop or start the active route.
To add via points (extra stops) during a route:
1. Press the MENU key, highlight Route Options, and press OK. A Route
Options menu appears.
2. Highlight Vias, and press OK. An information page for your current
route appears.
3. Use the Rocker pad to highlight the Via Points box, and press OK.
4. Highlight <Select to add via point>, and press OK. A window appears
with three options for finding your location.
5. Select one of the three options. Once you select an option, the new via
point appears on your route page.
6. To add more via points, repeat steps 4 and 5 above.
7. Highlight Navigate, and press OK when you are done. Your original
route is automatically recalculated to include the newly-added via
point(s).
To install the vehicle suction cup mount:
1. Align the ball on the end of the suction mount with the socket (hole)
on the back of the cradle. Press firmly to snap the mount and cradle
together.
2. Flip up the antenna on the back of the unit. Angle the Quest forward
and fit the bottom of the Quest into the cradle. Tilt the unit back until it
snaps in place.
3. To ensure a tight grip, clean and dry your windshield before you mount
the suction cup. Flip the lever on the suction cup toward you.
4. Place the suction cup on your windshield. Flip the lever back, toward
the windshield.
5. Plug the power cable into an available receptacle.
NOTICE TO STATE OF CALIFORNIA DRIVERS: California Vehicle Code Section 26708 (a) (1) provides
that drivers in California should not use suction mounts on their windshield or side or rear windows. Other Garmin
dashboard or friction mounting options should be used. For available accessories, refer to the Garmin Web site at
www.garmin.com. Also, refer to the Owner’s Manual for instructions on using the included mounting disk with the
suction cup mount.
© Copyright 2006 Garmin Ltd. or its subsidiaries
January 2006 1 90-00556-11 Rev. A Printed in Taiwan
Finding Places and Routing to Them
To find a place and route to it:
1. Press the FIND key. A Find page appears.
2. Highlight an option that will help you find your destination, such as Auto
Fuel, Food & Drink, or Lodging. Press the OK key. A list of places near
your current location appears.
3. Highlight the place you wish to visit, and press OK. An information
page appears. (If you know you will want to visit this place again, select
Save to add it to your My Locations list.)
4. Highlight Route To on the information page, and press OK. Your Quest
calculates the route. Follow the calculated route to the destination.
To find an address and route to it:
1. Press the FIND key, highlight Addresses, and press OK.
2. A Wizard opens. Highlight the state if it appears on a button, or choose
Select State and find the correct name. Press OK.
3. Highlight Search All Cities, and press OK. You can also highlight
Spell City, and press OK. Enter the city using the on-screen keyboard.
4. Enter the address number and street using the on-screen keyboard.
For intersections, you only need to enter street names.
5. A list of addresses appears. Highlight the desired address, and press
OK. An Address page appears.
6. To create a route to this address, highlight Route To, and press OK.
Quest™ 2 Quick Reference Guide
Use this Quick Reference Guide to learn how to perform common
operations with your Quest 2. For a more thorough and detailed
explanation of operations and features, consult the Owner’s Manual.
Keep this guide in a handy place for future reference.
Turning the Quest On
Press and hold the Power key on the front of the unit to turn it on.
Vehicle Installation
Select a suitable location for installing the unit that allows routing of
the power cord and does not interfere with vehicle operation. Refer to
the safety warnings in the Owner’s Manual. Select a location where the
Quest’s flip-up antenna has an unobstructed view of the sky. For optimal
use, position the antenna parallel to the surface of the road.
Stopping & Starting Routes and Adding Via PointsInstalling the Suction Cup Mount
Suction
cup
Lever
Release
tab
Cradle
Suction
cup tab

To set a Home location:
1. Press the MENU key, highlight Route Options, and press OK.
2. Highlight Set Home Location, and press OK. A Set Home Location
menu appears.
3. Highlight one of the options: Use Current Location, Use Find Menu,
or Use Map, and then press OK.
4. Select your destination using this option. Your Home location is set.
To go Home:
Press and hold the FIND key.
To reset the trip data or the maximum speed:
1. On the Trip Information page, use the
Rocker pad to highlight the Trip or Max
buttons. Press OK.
2. A message asking if you want to reset
the data appears (Reset Trip Data? or
Reset Maximum Speed?).
3. Highlight Yes, and press OK. The data is
reset.
Shortcuts:
• Press and hold FIND to navigate to your Home location.
• Press FIND two times to display the Recent Finds page.
• Press and hold MENU to display the Route Options menu.
• Press MENU two times to display the Settings page.
• Press and hold OK to display the Where Am I? page.
• Press POWER to activate the backlight illumination window.
• Press zoom IN or OUT to page up or page down a list.
• Press IN and Power if your Quest freezes (stops responding to button
presses).
To find where you are:
1. Press the FIND key. The Find page appears.
2. From the Find page, highlight Where Am I?, and press OK. An
information page appears, listing your current location and nearest
major intersections.
To use TracBack:
1. Access the Where Am I? information page as described above.
2. Highlight TracBack, and press OK.
3. At the prompt, highlight Yes to TracBack to the beginning of the track,
and press OK.
4. Highlight a TracBack Preference (Follow Track, Faster Time, or
Shorter Distance), and press OK. The Quest calculates your route.
To adjust the backlight:
1. Press the Power key. An illumination window appears.
2. Press the Rocker pad left or right to dim or brighten your backlight.
3. Press OK.
To adjust the external speaker volume:
1. Adjust the volume control knob on the external speaker.
2. Press the SPEAK key to test the volume level.
To add a detour during a route:
1. Press the MENU key, highlight Route Options, and press OK. A Route
Options menu appears.
2. Highlight Detour, and press OK.
3. From the Detour Distance page, highlight the distance for which you
would like to alter your route, and press OK. Your original route is
recalculated to avoid the upcoming section of road.
To plan a route:
1. Press the MENU key, highlight Route Options, and press OK. A Route
Options menu appears.
2. Highlight Route Planner, and press OK. From the Route List page that
appears, highlight New, and press OK.
3. Highlight <Select your starting location>, and press OK. Select one
of the three options, and then select your starting location.
4. Highlight <Select your destination>, and press OK. Select one of the
three options, and then select your destination.
5. From the Route Planner window, highlight Navigate, and press OK.
Your Quest calculates the route.
Setting Your Home Location and Resetting Trip Info Finding Where You Are, Using TracBack®, and
Making Adjustments Using ShortcutsAdding Detours and Planning Routes
Trip Information Page